IDTECH IDP-05-L1 Bedienungsanleitung

ID TECH

10721 Walker Street, Cypress, CA 90630-4720

Tel: (714) 761-6368 Fax (714) 761-8880

www.idtechproducts.com

Lite-On Custom PiP User Manual

80179403-001 Rev. A

26 December 2022

Page | 2

ID TECH

10721 Walker Street

Cypress, CA 90630 USA

This document, as well as the hardware and software it describes, is furnished under license and may

only be used in accordance with the terms of such license. The content of this paper is furnished for

informational use, subject to change without notice, and not to be construed as a commitment by ID

TECH. ID TECH assumes no responsibility or liability for any errors or inaccuracies that may appear in this

document.

Except as permitted by such license, no part of this publication may be reproduced or transmitted by

electronic, mechanical, recorded, or any other method, or translated into another language or language

form without the express written consent of ID TECH. ID TECH is a registered trademark of International

Technologies and Systems Corporation. ViVOpay and Value through Innovation are trademarks of

International Technologies and Systems Corporation. Other trademarks are the property of the

respective owner.

Warranty Disclaimer: The services and hardware are provided "as is" and "as-available," and the use of

these services and hardware are at the user’s own risk. ID TECH does not make, and hereby disclaims,

any and all other express or implied warranties, including, but not limited to warranties of

merchantability, title, fitness for a particular purpose, and any warranties arising from any course of

dealing, usage, or trade practice. ID TECH does not warrant that the services or hardware will be

uninterrupted, error-free, or completely secure.

Page | 3

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna

or transmitter.

Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled

environment and are safe for intended operation as described in this manual. The further

RF exposure reduction can be achieved if the product can be kept as far as possible from

the user body or set the device to lower output power if such function is available.

Page | 4

This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM

Manual v01 guidance, the following conditions must be strictly followed when using

this certified module:

KDB 996369 D03 OEM Manual v01 rule sections:

2.2 List of applicable FCC rules

This module has been tested for compliance to FCC Part 15

2.3 Summarize the specific operational use conditions

The module is tested for standalone mobile RF exposure use condition. Any other usage

conditions such as co-location with other transmitter(s) or being used in a portable

condition will need a separate reassessment through a class II permissive change

application or new certification.

2.4 Limited module procedures

Not applicable.

2.5 Trace antenna designs

Not applicable.

2.6 RF exposure considerations

This equipment complies with FCC mobile radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with a

minimum distance of 20cm between the radiator & your body. If the module is installed

in a portable host, a separate SAR evaluation is required to confirm compliance with

relevant FCC portable RF exposure rules.

2.7 Antennas

The following antennas have been certified for use with this module; antennas of the same type with

equal or lower gain may also be used with this module. The antenna must be installed such that 20

cm can be maintained between the antenna and users.

Antenna Type Loop Antenna

Antenna connector N/A

2.8 Label and compliance information

The final end product must be labeled in a visible area with the following: “Contains

FCC ID: WQJ-PIPOEM”. The grantee's FCC ID can be used only when all FCC

compliance requirements are met.

2.9 Information on test modes and additional testing requirements

This transmitter is tested in a standalone mobile RF exposure condition and any co-

located or simultaneous transmission with other transmitter(s) or portable use will

require a separate class II permissive change re-evaluation or new certification.

2.10 Additional testing, Part 15 Subpart B disclaimer

This transmitter module is tested as a subsystem and its certification does not cover the

FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final

Page | 5

host. The final host will still need to be reassessed for compliance to this portion of rule

requirements if applicable.

As long as all conditions above are met, further transmitter test will not be required.

However, the OEM integrator is still responsible for testing their end-product for any

additional compliance requirements required with this module installed.

IMPORTANT NOTE: In the event that these conditions can not be met (for example

certain laptop configurations or co-location with another transmitter), then the FCC

authorization is no longer considered valid and the FCC ID can not be used on the final

product. In these circumstances, the OEM integrator will be responsible for re-evaluating

the end product (including the transmitter) and obtaining a separate FCC authorization.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding

how to install or remove this RF module in the user’s manual of the end product which

integrates this module.

The end user manual shall include all required regulatory information/warning as show in

this manual.

OEM/Host manufacturer responsibilities

OEM/Host manufacturers are ultimately responsible for the compliance of the Host and

Module. The final product must be reassessed against all the essential requirements of the

FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This

includes reassessing the transmitter module for compliance with the Radio and EMF

essential requirements of the FCC rules. This module must not be incorporated into any

other device or system without retesting for compliance as multi-radio and combined

equipment.

Page | 6

Industry Canada statement:

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas

produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y

compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

The product comply with the Canada portable RF exposure limit set forth for an uncontrolled

environment and are safe for intended operation as described in this manual. The further RF

exposure reduction can be achieved if the product can be kept as far as possible from the user body

or set the device to lower output power if such function is available.

Déclaration d'exposition aux radiations:

Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-

Unis et le Canada établies pour un environnement non contrôlé.

Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux

expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps

de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle

fonction est disponible.

This device is intended only for OEM integrators under the following conditions: (For module

device use)

1) The transmitter module may not be co-located with any other transmitter or antenna.

As long as the condition above is met, further transmitter test will not be required. However, the

OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour

utilisation de dispositif module)

1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

Tant que la condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront

pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit

final pour toutes exigences de conformité supplémentaires requis pour ce module installé.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-

location with another transmitter), then the Canada authorization is no longer considered valid and

the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be

responsible for re-evaluating the end product (including the transmitter) and obtaining a separate

Canada authorization.

Page | 7

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines

configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur),

l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur

le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit

final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.

End Product Labeling

The product can be kept as far as possible from the user body or set the device to lower output

power if such function is available. The final end product must be labeled in a visible area with

the following: “Contains IC:9847A-PIPOEM”.

Plaque signalétique du produit final

L'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif

est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. Le produit

final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 9847A-

PIPOEM".

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to

install or remove this RF module in the user’s manual of the end product which integrates this

module.

The end user manual shall include all required regulatory information/warning as show in this

manual.

Manuel d'information à l'utilisateur final

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant

à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final

qui intègre ce module.

Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et

avertissements comme indiqué dans ce manuel.

Cautions and Warnings

Caution: The LITE-ON CUSTOM PIP should be mounted 1-2 feet away from other PiPs. Can be adjusted

based on lane setup.

Warning: Avoid close proximity to radio transmitters which may reduce the capability of the reader.

Page | 8

Revision History

Date Rev

Changes By

12/26/2022

A Initial release EC

Table of Contents

1. OVERVIEW ......................................................................................................................................................... 9

1.1. Universal SDK ..................................................................................................................................................... 9

1.2. Encryption .......................................................................................................................................................... 9

1.3. Features .............................................................................................................................................................. 9

1.4. Approvals ............................................................................................................................................................ 9

1.5. Regulatory .......................................................................................................................................................... 9

1.6. Model Number ................................................................................................................................................. 10

2. LITE-ON CUSTOM PIP SPECIFICATIONS ............................................................................................................. 11

3. LITE-ON CUSTOM PIP INSTALLATION ............................................................................................................... 11

3.1. Parts List ........................................................................................................................................................... 11

3.2. Mounting the Lite-On Custom PiP .................................................................................................................... 12

3.2.1. Mounting Screws ................................................................................................................................. 12

3.3. Connecting to Power ........................................................................................................................................ 12

3.4. Connecting to the Data Port ............................................................................................................................. 12

3.5. Using the LITE-ON CUSTOM PIP for Value-Added Services .............................................................................. 12

3.6. Making a VAS Transaction ................................................................................................................................ 12

3.7. Notes on Installation Locations ........................................................................................................................ 13

4. LITE-ON CUSTOM PIP LED STATUS INDICATOR ................................................................................................. 14

5. RF INTERFERENCE ............................................................................................................................................ 14

6. FIRMWARE COMMANDS .................................................................................................................................. 16

6.1. ECC Key Management ...................................................................................................................................... 16

6.1.1. ECC Key Pair ......................................................................................................................................... 16

6.1.2. How to Create an ECC Key Pair Using Open-SSL .................................................................................. 16

6.1.3. How To Extract Key Data To Load In The Lite-On Custom PiP ............................................................. 17

6.2. Google Pay Smart Tap 2.1 Commands ............................................................................................................. 18

6.2.1. Set Configurable Group (04-03) .......................................................................................................... 18

6.2.2. Set SmartTap LTPK (C7-65) .................................................................................................................. 19

6.3. Apple VAS Firmware Commands ...................................................................................................................... 21

6.3.1. Set Merchant Record (04-11) .............................................................................................................. 21

6.3.2. Set Private Key (C7-66) ........................................................................................................................ 23

6.3.3. Set Configuration (04-00) .................................................................................................................... 24

6.4. Lite-On Custom PiP Firmware Commands for Both Platforms ......................................................................... 26

6.5. Poll On Demand and Auto Poll Settings ........................................................................................................... 26

6.6. Non-Payment Card Switching Support ............................................................................................................. 26

7. FIRMWARE UPGRADE ...................................................................................................................................... 28

8. CUSTOMER SUPPORT ....................................................................................................................................... 29

Page | 9

1. Overview

The ID TECH PIP OEM is a compact, standalone NFC device, designed to support loyalty programs that

Smart Tap as well as Mifare and other closed-loop protocols.

1.1. Universal SDK

A feature-rich Windows-based Universal SDK is available to aid rapid development of applications that

talk to PIP OEM. The SDK is available for the C# language on Windows and comes with sample code for

demo apps. To obtain the SDK and other useful utilities, demos, and downloads, be sure to check the

Downloads link on the ID TECH Knowledge Base (no registration required).

1.2. Encryption

LITE-ON CUSTOM PIP supports ECC.

1.3. Features

LITE-ON CUSTOM PIP supports the following:

 Apple VAS

 Google Pay Smart Tap

 Mifare 1K/4K, Plus, DesFire, Ultralight

 UART

 Suitable for retail, entertainment, and other locations that use loyalty value-added services but do

not require payment

 Consumer Intuitive: Equipped with an LED and sound to provide visual and audible cues to enable a

smooth and seamless experience

 Buzzer sound notification

This document assumes that users are familiar with their host systems and all related functions.

1.4. Approvals

 Apple VAS & Google SmartTap

1.5. Regulatory

 FCC Part 15

 CE Mark

 UL certified(PCB material to be UL approved and with UL marking)

 REACH

 PMN: PIPOEM

Page | 10

1.6. Model Number

 IDP-05-L1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IDTECH Computerhardware Handbücher

IDTECH

IDTECH Xpress CM200 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung