IDTECH SecureHead Bedienungsanleitung

ID TECH

10721 Walker Street, Cypress, CA 90630-4720

Tel: (714) 761-6368 Fax (714) 761-8880

www.idtechproducts.com support@idtechproducts.com

SecureHead™

Demo Program

SPI Interface

80101503-001 Rev. B

2 October 2019

SecureHead™ Demo Program

Page | 2

ID TECH

10721 Walker Street

Cypress, CA 90630

(714) 761-6368

www.idtechproducts.com

This document, as well as the hardware and software it describes, is furnished under license and may

only be used in accordance with the terms of such license. The content of this paper is furnished for

informational use, subject to change without notice, and not to be construed as a commitment by ID

TECH. ID TECH assumes no responsibility or liability for any errors or inaccuracies that may appear in

this document.

Except as permitted by such license, no part of this publication may be reproduced or transmitted by

electronic, mechanical, recorded, or any other method, or translated into another language or

language form without the express written consent of ID TECH. ID TECH is a registered trademark of

International Technologies and Systems Corporation. ViVOpay and Value through Innovation are

trademarks of International Technologies and Systems Corporation. Other trademarks are the

property of the respective owner.

Warranty Disclaimer

The services and hardware are provided "as is" and "as-available," and the use of these services and

hardware are at the user’s own risk. ID TECH does not make, and hereby disclaims, any and all other

excpress or implied warranties, including, but not limited to warranties of merchantability, title,

fitness for a particular purpose, and any warranties arising from any course of dealing, usage, or trade

practice. ID TECH does not warrant that the services or hardware will be uninterrupted, error-free, or

completely secure.

SecureHead™ Demo Program

Page | 3

FCC warning statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

The user manual for an intentional or unintentional radiator shall caution the user that changes or

modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Note: The grantee is not responsible for any changes or modifications not expressly approved by the

party responsible for compliance. Such modifications could void the user’s authority to operate the

equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter and must be installed to provide a separation distance of at least 20cm

from all persons.

Cautions and Warnings

Caution: The ViVOpay Vendi should be mounted 1-2 feet away from other

ViVOpay Vendi. Can be adjusted based on lane setup.

Caution: Danger of Explosion if battery is incorrectly replaced. Replace only with

same or equivalent type recommended by the manufacturer. Discard used

batteries according to the manufacturer’s instructions.

Warning: Avoid close proximity to radio transmitters which may reduce the ability

of the reader.

SecureHead™ Demo Program

Page | 4

Table of Contents

1. INTRODUCTION..................................................................................................................................................................................5

2. OVERVIEW...........................................................................................................................................................................................5

3. COMMAND MENU.............................................................................................................................................................................6

3.1. General Setting Menu ..........................................................................................................................................................6

3.2. Encryption Menu....................................................................................................................................................................7

3.3. COM Port Selection...............................................................................................................................................................8

3.3.1. Help...................................................................................................................................................................................................................................8

3.3.2. Manual Command and Reader output......................................................................................................................................................8

3.3.3. Manual Command Format................................................................................................................................................................................8

3.3.4. Reader Output............................................................................................................................................................................................................9

3.4. Command Output and Decrypted Data ..........................................................................................................................9

4. FIXED KEY ENCRYPTION..............................................................................................................................................................11

4.1. Encryption Settings............................................................................................................................................................11

4.2. Other Mode Fixed Key Encryption.................................................................................................................................12

4.2.1. Data Decryption.....................................................................................................................................................................................................12

5. IDTECH MODE- DUKPT ................................................................................................................................................................15

5.1. Level 4 Activate Authentication Sequence .................................................................................................................15

6. NON-ENCRYPT MODE..................................................................................................................................................................15

7. APPENDIX A: MAGNETIC HEADS MECHANICAL DESIGN GUIDELINES..........................................................................17

SecureHead™ Demo Program

Page | 5

1. Introduction

SPI SecureHead Demo Program is used to demonstrate the functionality of encrypted MSR. It

decrypts data by sending a command to MSR and loading key to MSR.

There are 4 modes available for the SPI reader:

•ID TECH Mode – Fixed Key

•ID TECH Mode – DUKPT Key

•Other Mode – Fixed Key

•Non-encrypted Mode

All four modes have different data output for the format key management scheme.

2. Overview

The SPI SecureHead Demo Program consists of 3 major sections:

•Command Menu

•Manual Commandand Reader Output

•Command Output and Decrypted Data

SecureHead™ Demo Program

Page | 6

3. Command Menu

The command menu provides MSR and encryption related settings. The settings available vary

between different reader modes.

3.1. General Setting Menu

The common settings available to all modes:

Set Default Configuration

Set the reader to default settings:

MSR: Enable:

•Terminator Setting: CR

•Preamble Setting: None

•Postamble Setting: None

•Track Selected Setting: Any Track

•Sentinel and T2 Account No: Send Sentinels and all T2 data

•Data Edit Setting: Disabled

•Track 1/2/3 Prefix: None

•Track 1/2/3 Suffix: None

Note: These features are applicable in non-encrypted mode only.

Read Current Configuration

The reader outputs current configuration settings.

Read Firmware Version

The reader returns the current firmware version.

MSR Enable

This command enables the MSR.

MSR Disable

This command disables the MSR. The reader does not send out data after a card swipe when the

MSR is disabled.

Clear Reader Output

This command clears the reader output text field.

ID TECH has several decoding options for non-encrypted mode:

•ID TECH Raw Format

•ID TECH Decoded – both directions

SecureHead™ Demo Program

Page | 7

•ID TECH Decoded – forward direction only

•ID TECH Decoded – backward direction only

When decoded format is selected, the reader can be configured to send out data in either raw or

decoded format from a card swipe.

3.2. Encryption Menu

This menu is to set security related features. See the encryption settings in each reader mode.

ID TECH Mode: Fixed Key

•TDES

•AES

•Get encrypted challenge

•Send authentication data

•Load key

ID TECH Mode: DUKPT Key

•TDES

•AES

•Get security level

•Get KSN

Other Mode: Fixed Key

•Get encrypted challenge

•Send authentication data

•Load key

•Enable encryption

•Disable encryption

The ID TECH output format default is TDES, but the user can select TDES or AES as the encryption

algorithm. For Other mode, the encryption algorithm is always TDES.

Use the Get Security Level command to verify the reader’s security level under DUKPT key

management. The security level is the 5th byte from the left of the Command Response in hex. For

example, security level 3 has a command response of OUT: 06 02 7E 01 33 03 4D.

SecureHead™ Demo Program

Page | 8

3.3. COM Port Selection

By default, COM1 is used when the demo software is opened. If the user prefers to communicate

with the reader through different serial port or close the port, the port setting can be modified in Port

Setting menu.

3.3.1. Help

The Help menu displays the demo program’s version information.

3.3.2. Manual Command and Reader output

In this field, a user can manually type commands to send to the reader. Click Send Command to send

the command to the reader. The Command structure is described in next section.

3.3.3. Manual Command Format

Manually input commands and send settings to the device.

Command Format:

SPI Protocol

ATMEL Protocol

where:<STX> = 02h, <ETX> = 03h, <ATMEL Function ID> = 54h,

<Len1> and <Len2> are two bytes length in SPI Protocol

<LRC> is one-byte XOR value calculated from <STX> to <ETX>.

The user is only required to enter the Command_Data parameter; the demo software automatically

encapsulates the ATMEL Protocol and SPI Protocol.

For example:

Read Firmware Version

1. Enter “52 22” in the Manual Command / Reader Output window

2. Click Send Command. The demo software will encapsulate ATMEL Protocol’s STX,

ATMEL Function ID, two bytes length, SPI Protocol’s STX, ETX, LRC, and ATMEL

Protocol’s ETX and LRC.

SecureHead™ Demo Program

Page | 9

For example: 52 22 02 54 00 05 02 52 22 03 71 03 50

For the complete command protocols, please see the SecureHead SPI manual.

3.3.4. Reader Output

This field displays the card data when a card is swiped. The field displays the unencrypted data when

the reader is not encrypted. The field displays the encrypted card data when the reader is encrypted.

The program shows the decrypted data in the lower field when the Decrypt button is selected.

Below is an example of the encrypted MSR data, sent by the reader in ID TECH Fixed Key Mode:

If no reader data is sent for more than 3 seconds, the current MagSwipe data in Reader Output

window will be replaced by the next MagSwipe data. Otherwise, the new data will append after the

current data.

To clear the reader output:

1. Navigate to General Setting menu

2. Select Clear Reader Output.

3.4. Command Output and Decrypted Data

The command sent to the reader and the command output in hex format are displayed in this section.

For output command status, 06h means command success and 15h indicates a failure.

This section also displays decrypted MSR data with key value and KSN.

Below is an example result of decrypting an ISO standard bank card; top field displays both the reader

output and the masked data, and the bottom field shows the decrypted card data.

SecureHead™ Demo Program

Page | 10

Andere Handbücher für SecureHead

Inhaltsverzeichnis

Andere IDTECH Aufnahmegeräte Handbücher

IDTECH

IDTECH Vivopay Neo 2 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch