Ikegami Electronics VCM-1501 Bedienungsanleitung

Operating Instructions

For Color Video Monitor

VCM-1501 / VCM-1701

Table of Contents

1. FCC Information - 2

2. Safety Precautions - 2

3. General Features - 4

4. VCM-1501 HI-RES. Monitor Front and Rear Views - 5

5. VCM-1701 HI-RES. Monitor Front and Rear Views - 6

6. Operation - 7

7. Specifications - 8

8. Rack Mount Kit Model - 9

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation.

If his equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables and A.C. power cord, if any, must be used in order to comply

with emission limits.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

SAFETY PRECAUTIONS

1. Operate this unit only from the type of power source indicated on the label.

2. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.

3. Do not place this monitor near a radiator or heating vent.

4. Do not push objects of any kind through cabinet openings. This may result in fire or

electrical shock.

5. Before adding attachments always ask a service technician to perform routine safety

tests to determine that equipment is in safe operating condition. Ground potential tests

should be part of the routine safety check made by the service technician.

6. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure

personnel or damage equipment.

7. Route power cords so that they cannot be walked upon or tripped over. Do not allow

anything to rest on the power cord.

8. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not

spill liquid of any kind on the unit.

9. Unplug the power cord from the unit before cleaning the display. Use only a damp cloth.

Do not use alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO

CLEAN THE INTERIOR OF THIS UNIT- THIS ACTION MUST BE PERFORMED BY

THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE.

10. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY

UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS

VOLTAGES OR OTHER HAZARDS.

12. Unplug the unit immediately and notify the service technician.

A. If liquid has been spilled into the display or the display has been exposed to rain

or water.

B. If the unit has been dropped or the cabinet damaged.

C. If fuses continue to blow.

D. If the power cord is damaged or frayed.

E. If a distinct change from normal operation is apparent.

When replacement parts are required, be sure that the service technician uses

components specified by the manufacturer which have the same characteristics as the

original parts. UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL

SHOCK OR OTHER HAZARDS.

Upon completion of any service or repairs, ask the technician to perform

safety checks to determine that the equipment is in safe operating condition.

WARNING: Serious shock hazards exist within the covers of this monitor. Do not open the

covers under any circumstances, there are no user serviceable components inside.

GENERAL FEATURES

1. Compatible With : NTSC / PAL System

2. Scanning System : NTSC, 525 Lines, 60 Hz or PAL, 625 Lines, 50 Hz

3. Video Input Signal : CVBS1 / CVBS2 / S-Y/C

4. Audio Input Signal : AU1 / AU2

5. Input Power : 100~240V AC

6. Limited twelve months warranty

STANDARD SYSTEM COMPONENTS AND ATTACHMENTS

The various components and attachments are shown below:

VCM-1501 VCM-1701

VCM-1501 MONITOR FRONT AND REAR VIEW

Front View

1. Power On/Off Switch

2. Power-On Indicator

3. Contrast Adjustment

4. Brightness Adjustment

5. Tint Adjustment

6. Color Adjustment

7. Sharpness Adjustment

8. Volume Adjustment

9. CVBS1 / CVBS2 / S-Y/C Select Switch

10. Audio 1 / Audio 2 Select Switch

VCM-1501

Rear View

1. Power Inlet

2. Video 1 Load Impedance Switch

3. Video 2 Load Impedance Switch

4. Video 1 Input : BNC Connector

5. Video 1 Output : BNC Connector

6. Video 2 Input : BNC Connector

7. Video 2 Output : BNC Connector

8. Audio 1 Input : RCA Jack

9. Audio 1 Output : RCA Jack

10. Audio 2 Input : RCA Jack

11. Audio 2 Output : RCA Jack VCM-1501

12. S-Y/C Load Impedance Switch

13. S-Y/C Input Connector

14. S-Y/C Output Connector

VCM-1701 MONITOR FRONT AND REAR VIEW

Front View

1. Power On/Off Switch

2. Power-On Indicator

3. Contrast Adjustment

4. Brightness Adjustment

5. Tint Adjustment

6. Color Adjustment

7. Sharpness Adjustment

8. Volume Adjustment

9. CVBS1 / CVBS2 / S-Y/C Select Switch

10. Audio 1 / Audio 2 Select Switch

VCM-1701

Rear View

1. Power Inlet

2. Video 1 Load Impedance Switch

3. Video 2 Load Impedance Switch

4. Video 1 Input : BNC Connector

5. Video 1 Output : BNC Connector

6. Video 2 Input : BNC Connector

7. Video 2 Output : BNC Connector

8. Audio 1 Input : RCA Jack

9. Audio 1 Output : RCA Jack

10. Audio 2 Input : RCA Jack

11. Audio 2 Output : RCA Jack

12. S-Y/C Load Impedance Switch VCM-1701

13. S-Y/C Input Connector

14. S-Y/C Output Connector

OPERATION

Operating Instructions

1. Place the monitor on a flat and firm surface (see Safety Precautions on page 2).

2. This monitor can be operated between 100VAC to 240VAC.

3. Plug the power cord into AC outlet on the wall.

4. Link the A / V terminal from your devices into the audio / video in RCA/BNC connectors

of the monitor.

5. Turn your device system power switch ON. then turn the monitor power switch ON.

The power indicator will be ON at this moment.

6. Allow about 30 seconds for the display tube to warm up, then the image should appear

on the screen.

7. The monitor will detect the frequency of the input signal automatically, and the image

may be adjusted through the function VR on front control panel.

8. Adjust the user controls to optimize picture quality.

MAINTENANCE

If the quality of the picture is poor and cannot be improved by making adjustments on the

front control panel, inspect all system connections and cable runs.

To reduce the risk of electrical shock, do not remove the cover or back of monitor. No user-

serviceable parts are inside. Refer servicing to qualified personnel, or contact the Tatung

Customer Service Department for assistance. Refer to the Warranty and Return

Information section.

SPECIFICATIONS

MODEL

ELECTRICAL VCM-1501 VCM-1701

Input Voltage 100~240V AC, 60 / 50HZ , full range

Power

Consumption 70W 72W

Horizontal

Resolution 700 lines, Y/C

more than 800

lines

700 lines, Y/C

more than 800

lines

Sweep Linearity 10﹪

GENERAL

Input / Output

Video / S-Video 2

BNC inputs, 2

75ohms, or Hi-Z

2 looping through

outputs

1 input DIN

1 loop through

output

BNC inputs,

75ohms, or Hi-Z

2 looping through

outputs

1 input DIN

1 loop through

output

Audio 2

RCA input, Hi-Z 2

2loop through

output

RCA input, Hi-Z

2loop through

output

Dimensions （㎜） 356x333x381 405x370.5x406

Weight （N.W.）15.7kgs 19.4kgs

ENVIRONMENTAL

Operating Temperature 32°to 106℉（0° to 41℃）

Humidity 0﹪to 90﹪（non-condensing）

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ikegami Electronics Monitor Handbücher

Ikegami Electronics

Ikegami Electronics HEM-1770WR Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung