iLiving ILG8SFSC Bedienungsanleitung
Fan Speed Controller
MODEL: ILG8SFSC
(PF-4C929A)
OWNER’S MANUAL
PLEASE READ AND SAVE
THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
1. Disconnect power supply before wiring connections are made to prevent possible electric
shock and/or damage to equipment.
2. Read and follow instructions carefully. Failure to comply with instructions could result in
fire, electric shock, injury to persons, and/or damage to equipment.
3. To reduce the risk of overheating and possible damage to other equipment, this speed
controller is only intended for use with the iLIVING Variable Speed Shutter Exhaust Fans
(ILG8SF10V, ILG8SF12V, ILG8SF16V, ILG8SF18V, ILG8SF20V, and ILG8SF24V). Do
not install this speed controller on any other fan or appliance.
4. All wiring should conform to the United States National Electrical Code and all applicable
local/state regulations.
5. Do not mount the controller in an area which will likely expose the controller to moisture.
6. Make certain the entire installation is grounded as a precaution against possible electrical
shock.
7. Do not exceed maximum amperage rating of the controller as overloading can result in
damage to the shutter exhaust fan and controller.
8. When wiring an electrical appliance or device follow all electrical and safety codes, as
well as the most recent United States National Electrical Code (NEC) and the
Occupational Safety and Health Act (OSHA).
9. Install controller in a well-ventilated area.
CAUTION: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE
THIS CONTROLLER IN AN INSULALTED WALL
Installation
1. Turn power off at circuit breaker panel or fuse box.
2. Mount controller to standard single gang wall box.
3. Run conduit between the wall box, power source, and the fan units being controlled.
Leave approximately 4 inches of wire in the box for connections.
To Motor
White
Neutral
(White)
Hot
(Black)
Black
To Power Supply
4. Make wiring connections as shown. Connect the black wire from the supply line to one of
the black wires of the controller. Connect the second black wire of the controller to the
black wire from the fan motor. Connect the white wire from the supply line to the white
wire of the fan motor. Make sure that the wire strands are straight and secure the wire
leads of the control to the circuit wires by twisting them together. Twist a wire nut onto
each connection.
5. Alignment - arrow mark pointing upward for upright position. Cover dent on cover plate
shows upward position.
"One black wire from the speed controller connects to the power supply, the other black wire from the speed controller
connects to the fan. The black wires on the right and left side of the speed controller can be used interchangeably."
6. When any solid state speed controller is used, a humming noise will be present in the fan
on low speed. This hum in no way affects the operation of the fan and is acceptable in
most commercial/industrial installations.
Operation
NOTE: Factory preset low speed setting is normally acceptable in most installations. In the
event a slower speed is desired, read the following additional instructions:
1. To change the minimum speed setting, set the controller on low setting and remove the
knob and black cover plate.
2. Adjust the trim setting through the access opening in the front of the control using a small
insulated flat tipped screwdriver. With fans running on low speed setting, trim the
adjustment screw slightly counterclockwise to further reduce speed.
3. Allow time for fans to slow (approximately one minute) before proceeding with further
adjustment.
4. After final setting, replace black cover plate and knob.
iLIVING USA
239 Harbor Way
South San Francisco, CA 94080
Tel: 800-317-1688
Email: service@ilivingusa.com
Like us on Facebook: https://www.facebook.com/ilivingusa/
Follow us on Twitter: @iLIVINGUSA
Check out our website: www.ilivingusa.com
Knob
Trim Adjustment
Screw
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere iLiving Controller Handbücher
