Illuburg ST-25M-DALI2 Betriebsanleitung

Datasheet & Operating instructions  ST-25M-DALI2  Page 1/10

www.illuburg.de

Datasheet & Operating instructions

Model: ST-25M-DALI2

LED power supply with adjustable output current

25 W max., IP20, independent installation

dimmable with DALI2, PUSH (pri.)

Flicker-free according to IEEE 1789

Datasheet & Operating instructions  ST-25M-DALI2  Page 2/10

www.illuburg.de

Safety Instructions

• Be sure to switch off the mains voltage before assembly and disassembly.

• Please keep this product away from children and pets.

• Do not place this product under any mechanical stress.

• Handle this product with care. Jolts, impact or falling from even a low height could damage this product

and jeopardize its safe operation.

• If this product is visibly damaged / no longer works properly / has been stored for extended periods in

poor ambient conditions, please take the product out of service and protect it from any

unintentional/accidental use.

• Compare the technical data of all products used, these must be compatible to each other and be within

the specified range. Also observe the safety and operating instructions of any other devices which are

connected to this product.

• Make sure that the total power of the connected LED lighting does not exceed the maximum output

power of the product (see electrical data).

• Only operate the product within the specified ambient temperature (ta) range (see operating condition).

• Only operate the product in an environment that corresponds to its IP protection class and protect the

product from extreme temperatures, direct sunlight, strong shocks, flammable gases, vapors & solvents.

• Never immerse the product in water or other liquids.

• Consult an expert if you have any doubts about the operation, safety or connection of the product.

• Only have maintenance, adjustment and repair work carried out by an expert or at a qualified workshop.

• If you have questions which remain unanswered by these operating instructions, contact our technical

support service or other technical personnel.

Read the operating instructions carefully and especially observe the safety information. If you do not follow

the safety instructions and information on proper handling in this manual, we assume no liability for any

resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee

Datasheet & Operating instructions  ST-25M-DALI2  Page 3/10

www.illuburg.de

Intended use

The LED power supply is a power supply device specially designed for LED lighting. For safety and approval

purposes (CE), you must not rebuild and/or modify this product. If you use this product for purposes other

than those described above, the product may be damaged. In addition, improper use can cause hazards

such as short circuits, fire, electric shock, etc. Read the following notes and the datasheet carefully and

completely, they are part of the product and contain important information. Please keep this document

and only pass the product on to third parties together with this document.

This product complies with statutory national and European requirements. All company names and product

names contained are trademarks of their respective owners.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the household

waste. At the end of its service life, dispose of the product according to the relevant

statutory regulations. You thus fulfil your statutory obligations and contribute to the

protection of the environment.

Datasheet & Operating instructions  ST-25M-DALI2  Page 4/10

www.illuburg.de

Exploded view

Datasheet & Operating instructions  ST-25M-DALI2  Page 5/10

www.illuburg.de

Electrical data

Rated input voltage 220...240 Vac

Range of input voltage 198...264 Vac

Range of input voltage (DC) 200...240 Vdc

Mains frequency 50/60 Hz

Power factor (λ) ≥ 0.95 Full Load, 230 Vac

No-load power consumption < 0.5W

Standby power consumption < 0.5W

Input current 0.14 A max.

Inrush current 8 A max. 50us@230Vac, Cold Start 50%

Ipeak

Output voltage 30-72 Vdc (No-load 82Vdc max.)

Output options 200 mA, 30-72 Vdc, 6-14.4 W

250 mA, 30-72 Vdc, 7.5-18 W

300 mA, 30-72 Vdc, 9-21.6 W

350 mA, 30-72 Vdc, 10.5-25.2W

Output power (nominal) 25 W max.

Efficiency 86 % max. Full Load, 230 Vac

Life time 5 years @Ta, Full load 230 Vac

Dimming range DALI-2 DT-6: 0-100%, max. lead length: 300M.

PUSH (Primary): 2-100%, max. lead length: 20M, max. 20 pcs parallel

Memory Funktion(PUSH) yes

Operating condition

Operating temperature range (ta) -25...+50 °C

Max. Surface temperature (tc) 85 °C

Permitted rel. humidity 10...95 % (non-condensing)

Protection class II

Type of protection IP20

Datasheet & Operating instructions  ST-25M-DALI2  Page 6/10

www.illuburg.de

Protection

Short circuit protection Yes *

Overvoltage protection Yes *

Overheating protection Yes *

Overload protection Yes *

No-Load protection Yes *

(*) The output shuts off and will be resumed, after problem is removed and led driver is restarted.

Standards

EN 61347-1, EN 61347-2-13, EN 62493, EN60598-1

EN 61000-3-2, EN 61000-3-3

EN 55015, EN 61547

Standards (DALI) IEC 62386-102, IEC 62386-207 DT6

Approval marks CE, UKCA

RoHS compliant Yes

Installation

Type of installation Independent installation

Type of connection Spring-loaded terminal

Cable cross-section, input side 0.75...1.5 mm²

Cable cross-section, output side 0.75...1.5 mm²

Cable preparation length, input side 6...8 mm

Cable preparation length, output side 6...8 mm

Circuit breaker (230V) 10A Typ B: 25 pc.

13A Typ B: 30 pc.

16A Typ B: 40 pc.

20A Typ B: 50 pc.

25A Typ B: 60 pc.

10A Typ C: 40 pc.

13A Typ C: 55 pc.

16A Typ C: 65 pc.

20A Typ C: 85 pc.

25A Typ C: 100 pc.

Datasheet & Operating instructions  ST-25M-DALI2  Page 7/10

www.illuburg.de

Dimension

Connection

Datasheet & Operating instructions  ST-25M-DALI2  Page 8/10

www.illuburg.de

Control via PUSH Button

Action Duration Status Function

Short press once < 0.5 s

LED on Turn off LED

LED off Turn on LED with latest brightness setting

Long press and

hold

0.5-14 s LED on Dim the brightness up / down.

Each new long press changes the dimming direction.

> 15 s LED on Synchronize all LED-Drivers with 100% brightness*

> 0.5 s LED off Turn on and synchronize all LED-Drivers with 5% brightness*

* In case of parallel connection with multiple LED power supplies using single PUSH button

Datasheet & Operating instructions  ST-25M-DALI2  Page 9/10

www.illuburg.de

Make sure there is a clearance of at least 15cm

between the LED driver and other heat sources,

e.g., other LED power supplies, lamps/LEDs etc.

A distance of at least 5cm between the LED power

supply and other non-heat-producing

objects/surfaces is required.

Have the product installed by a qualified expert (e.g., electrician) who is familiar with

all applicable regulations! When handling mains voltage improperly, you will not only

endanger yourself but also others! If you do not have the relevant expert knowledge, do not

install the product yourself, but have it done by an expert.

Installation

• compare all products to be compatible to each other.

• The product must be completely free of voltage for installation.

• Turn off the corresponding circuit breaker and/or automatic fuse to remove all voltage from the power

circuit. Secure them against unauthorized restart, e.g., by installing a warning sign. Also switch off the

relevant circuit breaker in order to disconnect all poles of the mains cable from the mains supply.

• First, connect your LED lighting to the screw terminals / spring terminals / cables on the secondary side

(SEC), ensuring correct polarity. Connect the mains supply line to the corresponding screw terminals / spring

terminals / cables on the primary side of the LED driver (PRI). Make sure that all connections are firmly

tightened.

• Install the product using the two mounting openings to an even, stable surface.

• Make sure not to damage any cables, wiring or pipes that may run beneath the installation surface when

installing the product.

• Finally, make sure the LED driver is correctly connected; do not turn on the power supply until you have

verified that the product is installed correctly

• The LED driver is operational as soon as voltage is applied to the primary side.

Inhaltsverzeichnis

Andere illuburg Stromversorgung Handbücher

illuburg

illuburg ST-46M-DALI2 Bedienungsanleitung

illuburg

illuburg ST-50M2-PV Betriebsanleitung

illuburg

illuburg ST-30M-DALI2 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung

illuburg ST-25M-DALI2 Betriebsanleitung

Beliebte Stromversorgung Handbücher anderer Marken