ILY Enterprise CoolCopy 3 Bedienungsanleitung



User’s Manual

CoolCopyD1AL(DVD-Backup)

CoolCopyD 3

CoolCopyD 7































Table of Contents

Chapter 1 Introduction

.................................................................4

1.1 Overview ....................................................................................4

1.2 Features .....................................................................................4

1.3 Specifications ............................................................................4

Chapter 2 Installation Procedure

.............................................5

2.1 Controller only ........................................................….…..........5

2.2 Whole duplicator without writer installed ..….........................5

2.3 Completed duplication system ...................….........................5

Chapter 3 Key Functions and Operating Instruction

……8

Chapter 4 Function

..........................................................….......…9

4.1 Copy ................................................................…........................9

4.2 Test ....................................................................................…..…9

4.3 Test&Copy ...........................................................…....…...........10

4.4 Verify ....................................................................…..................10

4.5 Compare ..............................................................…...............…11

4.6 Prescan ................................................................…..................11

4.7 Disc Info ........................................................................…….....12

4.8 Select Source................................................................….........12

4.9 Image .........................................................................................12

4.9.1 Load .....................................................................................13

4.9.2 Delete Image ........................................................................13

4.9.3 Image Info .............................................................................13

4.9.4 Compare Image ....................................................................14

4.9.5 Select Partition ......................................................................14

4.9.6 Select Src Drive ....................................................................15

4.10 Edit Track ...............................................................................15

4.10.1 CD to CD Edit......................................................................16

4.10.2 CD to HD ............................................................................17

4.10.3 Play Audio Track ................................................................18

4.10.4 Close Session ....................................................................18

4.11 Setup.........................................................................................19

4.11.1 Language (optional)....................................................…......19

4.11.2 Burn Speed .........................................................................19

4.11.3 Read Speed ........................................................................19

4.11.4 Auto Start Drive ...................................................................20

4.11.5 Start up menu ......................................................................20

4.11.6 Auto Verify ...........................................................................20

4.11.7 Auto Compare ......................................................................20

4.11.8 Auto Prescan .......................................................................21

4.11.9 Eject Disc ............................................................................21

4.11.10 Burn on The Fly ................................................................21

4.11.11 Burn Mode ........................................................................21

4.11.12 Button Sound ....................................................................22

4.11.13 Device Info ....................................................................…22

4.11.14 System Info .......................................................................23

4.11.15 Quick Erase ......................................................................23

4.11.16 Full Erase ..........................................................................23

4.12 Adv Setup...................................................................................24

4.12.1 UnderRun Protect ...............................................….............24

4.12.2 Overburn ...............................................................…...........24

4.12.3 Read Error Skip............... ..................................…..…... ...24

4.12.4 Format Hard Disk ....................................................….........24

4.12.5 Verify HDD ...............................…..................................…...25

4.12.6 Burn-in.................................................…...…........................25

4.12.7 Update Firmware..........................................................….....25

4.12.8 Compare Firmware .......................................................…....26

4.12.9 H/W Diagnostic ...............................................................…..26

4.12.10 Load Default ..................................................................….26

Chapter 5 Troubleshooting

.........................................................27

Chapter 1 Introduction

1.1 Overview

People who want to create multiple copies of their DVDs or CDs usually take a long time to do so.

They might not have enough DVD+RW drives or they might be using their computers for some

other important tasks. The duplication process noticeably slows down a computer during the

burn process. Rather than sit at the computer for hours duplicating discs one at a time, it is much

more efficient to use a CoolCopyD DVD/CD duplication system.

The CoolCopyD DVD Duplicator system is a standalone duplicator and does not need to be

connected to a computer. It can duplicate discs accurately and quickly. With its multi-function

LCD panel, CoolCopyD DVD Duplicator is easy for any user to operate. It is a cost-efficient DVD-

R duplicator for audio, data, and video applications. The simple control panel is designed to

provide copy mode selection and copy operation.

1.2 Features

•Standalone IDE to IDE DVD Copy controller

•2(CoolCopyD1AL(DVD-Backup)) / 4(CoolCopyD3) / 8(CoolCopyD7) /

16(CoolCopyD14)

independent IDE channel

•Self system diagnostics when power on

•Supports Hard Drive image

•Auto format detection

•User friendly interface with message rich LCD display

•Fast copies supports high speed DVD-RW writing mode

•Easy operation without software and training are required

•Firmware upgrade via DVD-ROM

1.3 Specification

Power requirement – voltage: 5VB+/- 5%

Current: 0.5A Max.

Environment - Temperature

Operating 0˚ C to 70˚ C

Storage -20˚ C to 85˚ C

Humidity - 15% to 90%

Models: CoolCopyD3/CoolCopyD7

Dimensions - Length: 200 mm

Width: 146.2 mm

Height: 42 mm

Connectors - 40-pin internal IDE connector

Cable (Optional) - Using ATA-66 (*Cable of length do not use longer than 46cm)

DVD Format - DVD-ROM (Mode1 & Mode2), DVD-ROM/XA (Mode2 form1 & form2),

DVD-DA,

Mixed-Mode, Video DVD, DVD-I, Karaoke CD, Photo CD (Single & Multi-

session), CD-Extra, HFS, CD Bridge, ISO9660, CD-R, and DVD+RW

Writing mode - Auto Detect (DAO, TAO)

Supported DVD-ROM Drive* - EPO, TEAC

Supported DVD-RW Drive* - Plextor, TEAC, Lite-On, Asus, SONY

Chapter 2 Installation Procedure

When you purchase the CoolCopyD DVD Duplicator, the package may be packaged in the

following ways: controller only, whole duplicator without writer installed or a complete duplication

system.

2.1 Controller only

1. Before the installation, please prepare the necessary devices as following:

•DVD-ROM drive

•DVD-R/RW drive

•IDE case (2~10-bay chassis suggested).

•Hard drive and mobile rack (IDE-bus hard drive-Option)

•Switching power supply (300W suggested).

2. After the preparation as above and make sure:

•All IDE devices must be in master mode.

2.2 Whole duplicator without writer installed

•Unpack the duplicator.

•Prepare the DVD-R/RW writers according to the recommendation list. Please check with

the supplier about compatibility issues regarding unlisted DVD-R/RW drives.

•Assemble the duplicator according to your need.

•Make sure that the voltage setting is correct.

2.3 Completed duplication system

•Take the duplication system out of the package.

•Check the entire unit to see if there are any problems.

•Make sure that the voltage setting is correct.

•The hard drive is optional.

Hardware Connection of CoolCopyD1AL (DVD-Backup) without a HDD

CoolCopy1AL (CD-Backup)

DVD

ROM

DVD+/

Power

Hardware Connection with Hard Drive for CoolCopyD3

When the system connects with the hard drive, the hard drive must connect on the IDE 0 port

with the “Master” setting and the DVD-ROM must set at “Slave”.

Hardware Connection without Hard Drive for CoolCopyD3

Coolcopy 3

IDE 0

DVD

Pow

IDE 3

DVD+/

IDE 2

DVD+/

IDE 1

DVD+/

Coolcopy 3

IDE 3

DVD+/

IDE 2

DVD+

IDE 1

DVD+

IDE 0

DVD

ROM

Pow

Hardware Connection with Hard Drive for CoolCopyD7

When the system has a hard drive connected, the hard drive must connect on IDE 0 port with

“Master” setting and the DVD-ROM must set at “Slave.”

Hardware Connection without Hard Drive for CoolCopyD7

Coolcopy 7

IDE 4

DVD+RW

IDE 3

DVD+RW

IDE 2

DVD+RW

IDE 1

DVD

IDE 8

DVD+RW

IDE 7

DVD+RW

IDE 6

DVD+RW

IDE 5

DVD+RW

IDE

DVD+RW

IDE 1

DVD

IDE 8

DVD+RW

IDE 2

DVD+RW

IDE 7

DVD+RW

IDE 6

DVD+RW

IDE 3

DVD+RW

IDE 4

DVD+/

Pow

Chapter 3 Key Functions and Operating Instruction

1. LCD Display Panel: Display main functions and all messages.

2. Scroll up through menus or functions.

3. Scroll down through menus or functions.

4. Execute the function which you select.

5. Cancel the function which you select.

After turning the power on, the CoolCopyD DVD Duplicator will execute a self test for a few

seconds. After the self testing procedure runs, the LCD will show:

1. CoolCopyD3: CoolCopyD7:

Two main operation procedures

If you install a 3.5” hard disc, the operation procedures is as the following screen shows:

1. With hard drive installed

•Once duplicator detects a hard disc, it will ask if you want to format or not. A 10GB hard

disc can be divided into 10 partitions.

•Use the Select Source to set the hard drive as the target source.

•Then select which partition to store the data in function 9 “Image.”

•If there is no data stored in partition, place a source DVD into DVD-ROM and use

function 9-01 Load to transmit data from DVD into selected partition by pressing ENT.

Different data can be stored in different partitions.

•Switch to function 1, Copy, by pressing the arrow button. Place blank DVD-R or DVD-RW

discs into the DVD writers. Press “ENT” button to start copying.

•When a Copy completes, the passed (correctly copied) DVD discs will be ejected

automatically. The default setting is for the discs to be ejected automatically, but this can

be changed.

CD Duplicator

1-3 ver: 1.10B

CD Duplicator

1-7 ver: 1.10T

Initialize SDRAM.....

Detect Drives.....

1. Copy

•Failed discs will remain in writers. The default setting is to keep failed discs in the writers,

but this can be changed. Press the buttons on the drivers to take the failed DVDs.

•During the duplication process do not press any button because interruption will harm the

device. DVDs will be damaged.

2. Without a hard drive installed

If you don’t install a 3.5” hard disc, the operation procedures will be as follows:

•Place the master disc in the DVD-ROM.

•Switch to function 1, Copy, by pressing arrow button. Place blank DVD-R or DVDRW

discs into all the DVD writers. Press ENT to start.

•When Copy completes, the passed DVDs will eject automatically. The default is to eject

automatically, but this can be changed.

•

Failed DVDs will remain in the writers. The default is keeping failed DVDs in the writers,

but you can change it. You need to press the “eject” buttons on the writers to take the

failed DVDs.

ATA-66 Cable Layout:

Please identify the two different kinds of cable before the hardware installation.

Chapter 4 Function

4.1 Copy

Use this function to copy data from a source DVD directly onto blank DVD discs. Before copying

make sure that the source DVD is placed into DVD-ROM. If you have a HDD, make sure there is

data in your HDD partition. If you are not sure about the success of your duplication job, you can

use function 2 Test to simulate the copying process first.

Select function 1. Put a source DVD into DVD-ROM and blank DVD disks into DVD writers. DVD

rewriteable discs containing old data are usable, too.

LCD will show the process of copying

information as the following screen:

When copying is completed, the LCD will display as

the following screen:

Discs correctly copied will be ejected automatically

and failed ones will remain in the writers.

4.2 Test

Copying-24X 0%

650.0MB 74:00

Copy

OK: 03

Function 2 Test will simulate the copying process. When the simulation completes, the discs will

remain blank.

Press ENT button to start the disc simulation.

If you use DVD rewriteable discs that contain data, the old

Data will be quickly erased before simulation.

The LCD will show the testing

Information as the following screen:

When the process is finished, the LCD will

show the message as the following screen:

Stopping the test halfway does not affect the DVD discs. However, if the DVD rewriteable discs

contain important data, the information may be erased.

4.3 Test&Copy

Function 3 Test & Copy is to test first and then actually copy.

Select Function 3. Put a source DVD into DVD-ROM

and blank DVD discs into the writers.

Press ENT to start simulation. LCD will show the

information as the following screen:

After the tests finishes, actual copying will begin

as the following screen shows:

When the entire process finishes, the LCD will

show the information as the following screen:

4.4 Verify

Function 4, Verify, examines whether the target DVDs can be read correctly after copying.

Press ENT button to verify. The LCD will show as

the following screen:

The LCD will show verification information as

the following screen:

When the verification process is finished, the LCD

will display the result as such:

2.Test

Testing-24X 0%

650.0MB 74:00

Test

OK: 03

3.Test & Copy

Testing-24X 0%

650

0MB 74

Copying-24X 0%

650.0MB 74:00

Test & Copy

OK: 03

4.Verify

Verify--24X 0%

650.0MB 74:00

Verify

OK: 03

Andere Handbücher für CoolCopy 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ILY Enterprise DVD-Recorder Handbücher

ILY Enterprise

ILY Enterprise CoolCopy 3 Bedienungsanleitung

Beliebte DVD-Recorder Handbücher anderer Marken

Pioneer

Pioneer DVR-65H-S Einrichtungshandbuch

Sony

Sony RDR-VX525 - DVDr/ VCR Combo Bedienungsanleitung

Daewoo

Daewoo DHD-4000D Bedienungsanleitung

Medion

Medion MD 40570 Bedienungsanleitung

Philips

Philips ShowView DVDR3460H Bedienungsanleitung

Sony

Sony RDR-GX355 - Tunerless DVD Recorder Bedienungsanleitung

Sony

Sony DVDirect VRD-MC3 Bedienungsanleitung

Samsung

Samsung DVD-R130/XAA Bedienungsanleitung

FUNAI

FUNAI HD-B2735 Bedienungsanleitung

Panasonic

Panasonic DMR-EH54DEG Bedienungsanleitung

Pioneer

Pioneer PRV-LX1 Technisches Handbuch

Sanyo

Sanyo DRW-1000 Bedienungsanleitung

Philips

Philips DVDR610/05 Bedienungsanleitung

JVC

JVC DR-M10 Bedienungsanleitung

Samsung

Samsung SV-DVD40 Bedienungsanleitung

Philips

Philips DVDR3355 Bedienungsanleitung

FUNAI

FUNAI FDR-90E Bedienungsanleitung

LG RC298 Bedienungsanleitung