imilab EC3 Bedienungsanleitung
Read this manual carefully before use, and retain it for future reference.
EN ES
FR
DEPL
RU
IT KR TH VN AR
IMILAB EC3 Lite Outdoor Camera
User Manual
CONTENTS
English 01-08
33-40Deutsche
41-48Français
49-56Italiano
09-16Pусский
17-24Español
25-32Polski
81-88
ﺔﻴﺑﺮﻌﻟا
73-80Tiếng Việt
65-72ภาษาไทย
57-64한국어
Product Introduction
Packing list
Overview
Lens
Microphone Antenna
LED
Indicator light
Power supply
Wall Mounting Pack
Imilab EC3 Lite Outdoor Camera Power Adapter
User Manual
Read this manual carefully before use, and retain it for future reference.
IMILAB EC3 Lite Outdoor Camera
User Manual
Reset Button
Micro SD Card Slot
Speaker
EN-01
Installing the Device
Note: Please check that the Wi-Fi signal is strong enough before
mounting the device.
3. Put the base plate on the wall. Secure the base plate by inserting
the screws into the expansion nuts.
2. Insert three plastic expansion nuts into the holes.
1. Please make three marks on the wall first, and then drill three
holes at the positions. Drilling diameter of around 6.0mm,
drilling depth of around 30mm.
EN-02
Note: Please ensure that the device is suspended as shown after
installation.
4. Tighten the nut counterclockwise.
5. After adjusting the camera to the desired Angle, tighten the
bracket nut clockwise.
EN-03
Indicator Light
Steady blue on: connected/device status is normal
Flashing blue: network error
Flashing orange rapidly: waiting for connection
Flashing orange slowly: system upgrade in progress
Turn on the camera
Insert the power supply cable into the camera's power supply port.
Connect the other end of the power supply cable to a power source.
Restoring factory settings
Press and hold the reset hole with fine needle, then you can hear the
“reset succeed” voice. Data stored on the MicroSD card is not
deleted.
Insert a micro SD card
Ensure that the camera is disconnected from the power supply. Use
a screwdriver to remove the protective case and expose the micro
SD card slot. The contact points of the micro SD card should be
facing the same direction as the camera. Insert the micro SD card
into the slot.
Connecting the Device
Note:When inserting or removing the micro SD card, please disconnect the camera
from the power supply. Please use a micro SD card from a reputable manufacturer.
The recommended read and write speed of the micro SD card is at least U1/Class 10.
EN-04
Connect with Imilab Home app. This product works with Imilab Home
app. Control your device with Imilab Home app.
Scan the QR code to download and install the app.
Or search “ Imilab Home ” in the app store to
download and install it.
Open Imilab Home app, tap “+” on the upper right,
and then follow prompts to add your device.
Install Imilab Home App
Add Device
Open Imilab Home app, tap “+” on the upper right. Tap”[-]”and scan
the QR code on the power line by your phone, then you can follow
the steps to add your device.
Open Imilab Home app, tap “+” on the upper right. Tap”IMILAB EC3
Lite ”and then you can follow the steps to add your device.
Note: The version of the app might have been updated, please follow
the instructions based on the current app version.
Camera
IMILAB Outdoor
Security Cam...
IMILAB Home
Security Cam...
Please enter the device name to...
My device (6)
Imilab Home
IMILAB Home Security Cam...
IMILAB Home Security Cam... IMILAB Home Security Cam...
EN-05
For better results, avoid placing the camera in front of or next or a
glass surface, a white-colored wall or other reflective surfaces as
this may cause the recording to have un-even lighting between the
foreground and background or be over-exposed.
The working temperature of the device is -30℃ to 60℃. Do not use
the device when the temperature is too high or too low.
Specifications
Name: IMILAB EC3 Lite Outdoor Camera
Model: CMSXJ40A
Input: 12 V 1 A
Resolution: 2304×1296
Item Dimensions: 165×86×93 mm
Net Weight: 334 g
Waterproof: IP66
Operating Temperature: -30℃~ 60℃
Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4GHz
FCC ID: 2APA9-CMSXJ40A
Precautions
Please ensure that the device is within Wi-Fi signal coverage.
Place it at a location with good Wi-Fi signal strength.
Try to avoid placing the device near a metallicobject, a microwave
oven or other objects that may cause signal interference.
EN-06
FCC Statement
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. Thise
quipment generates, uses, and canradiate radio frequency energy,
and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC 20cm Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum
distance of 20cm between the radiator & your body. This transmi er
must not be co-located or operating in conjunction with any other
antenna or transmier.
EN-07
WEEE Disposal and Recycling Information
Correct Disposal of this product. This marking indicates that
product should not be disposal with other household wastes
through out the EU. To prevent possible harm to the
environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse
sustainable reuse of material resources. To return your used device,
please use the return and collection systems or contact the retailer
where the product was purchased. They can take this product for
environment safe recycling.
Adaptor Statements
For pluggable equipment, the socket-outlet (power adaptor) shall
be installed near the equipment and shall be easily accessible.
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio
equipment type IMILAB EC3 Lite Outdoor Camera is in compliance
with Directive 2014/53/EU.
EN-08
Andere Handbücher für EC3
5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere imilab Außenkamera Handbücher
