Industrial Products Handle It 3000 Bedienungsanleitung
Getting Started
12247 W. Fairview Ave, Milwaukee, WI 53226 · Phone (414) 453-5300 ·Toll Free (800) 236-1080
Rev A 7/10/2018
Installation
To get started wrapping pallets with the Handle It 3000 Robotic Stretch
Wrapper, unload the machine using the fork truck lift points at the front or
rear of the machine. Once the machine is unloaded, attach the guide wheel
using the 3 countersunk screws. Load the film on the carriage spindle and
route according to the diagram. The machine is now ready for use.
Operation
Power the machine on by turning the on switch and holding for 3 seconds. To
begin wrapping pallets, position the machine next to the desired pallet with the
controls located on the handle. Be sure there is an additional 56” clear around
the pallet for the machine to operate. Raise or lower the height of the guide
wheel as needed to allow smooth rotation around the pallet.
Manual Mode
Enter into manual mode by pressing , the carriage can then be raised up and down by pressing the
corresponding buttons on the display and holding in the start button. The robot can be moved with the
push buttons on the handle.
Creating a Cycle
The Handle It 3000 mobile robot allows you to customize and save several wrap cycles. To begin
editing a cycle press from the main screen. Select which slot you would like the program to
be saved in by pressing , this program can be saved with and loaded
with . Once the cycle is saved pressing will display the main screen and allow for
the machine to wrap with that particular cycle.
The Handle It 3000 has 14 customizable parameters that defines a cycle. The parameters are separated in
different pages on the display. Navigate these pages with and .
5717 Salmen Street New Orleans, LA 70123
www.industrialproducts.com
Getting Started
12247 W. Fairview Ave, Milwaukee, WI 53226 · Phone (414) 453-5300 ·Toll Free (800) 236-1080
Rev A 7/10/2018
Cycle Type: Toggle between
a pass up/down cycle or just
a pass up cycle.11
Middle Wraps: Set how
many times and at which
height (cm) the robot wraps.
Optional
Rotation Speed: Set how
quickly the robot moves
around the pallet.
Start Height: Set a height
(cm) that the robot begins
wrapping at. Optional
Tension: Controls the
amount of tension is
applied to the film.
Pallet Height: Turns off the
auto-height detection of the
machine and allows user to
set desired raised height.
Optional
Top Wraps: How many
times the machine wraps
the top of the pallet.
Pallet Perimeter: User sets
the perimeter (cm) that the
robot uses to determine
starting/stopping points. See
Perimeter Table for quick
values.
Bottom Wraps: How many
times the machine wraps
the bottom of the pallet.
Top Sheet: Enables Top sheet
cycle and has user determine
overhang of top sheet.
Up Speed: How quickly the
carriage rises.
Overwrap Height: The height
(cm) of film that goes over
the top of the pallet.
Down Speed: How quickly
the carriage lowers.
End Height: User determines
the height at which the
carriage is at the end of the
cycle. Optional
5717 Salmen Street New Orleans, LA 70123
www.industrialproducts.com
Getting Started
12247 W. Fairview Ave, Milwaukee, WI 53226 · Phone (414) 453-5300 ·Toll Free (800) 236-1080
Rev A 7/10/2018
Perimeter Table: Shows the perimeter (cm) of various sized pallets
Standard to Metric Conversion
30 36 40 42 48
30 305 335 356 366 396
36 335 366 386 396 427
40 356 386 406 417 447
48 396 427 447 457 488
60 457 488 508 518 549
72 518 549 569 579 610
84 579 610 630 640 671
96 640 671 691 701 732
120 762 792 813 823 853
144 884 914 935 945 975
Pallet Width (in)
Pallet Length (in)
in
1 2 3 4 5 10 15 20 25 30 40 50 60 70 80 90 100
cm
35810 13 25 38 51 64 76 102 127 152 178 203 229 254
mm
25 51 76 102 127 254 381 508 635 762 1016 1270 1524 1778 2032 2286 2540
5717 Salmen Street New Orleans, LA 70123
www.industrialproducts.com
Inhaltsverzeichnis
Andere Industrial Products Stretch-Wickelsystem Handbücher
