Inepro V2 Bedienungsanleitung
© 2014 Inepro B.V. All rights reserved
Technical Manual | Inepro IP Reader V2
Inepro IP Reader V2
Product Version: Rev.3 - V2
Version of this manual: 2.1.1
Inepro IP Reader V2
Congratulations on your selection of Inepro card readers. We are certain you will be
pleased with your purchase of one of the flexibele solutions of the market.
We want to help you get the best result from your Inepro Back Office Suite. This manual
contains information on how to do that; please read it carefully. Due to continuous
product improvements this manual is subject to changes without notice.
We strongly recommend you read the license agreement to fully understand its coverage
and your responsibilities of ownership.
Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer your
questions and your concerns.
Best wishes,
Inepro BV.
The most versatile card reader solution
All rights reserved. No parts of this work may be reproduced in any form or by any means -
graphic, electronic, or mechanical, including photocopying, recording, taping, or information
storage and retrieval systems - without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered
trademarks of the respective owners. The publisher and the author make no claim to these
trademarks.
While every precaution has been taken in the preparation of this document, the publisher and
the author assume no responsibility for errors or omissions, or for damages resulting from the
use of information contained in this document or from the use of programs and source code that
may accompany it. In no event shall the publisher and the author be liable for any loss of profit
or any other commercial damage caused or alleged to have been caused directly or indirectly by
this document.
Version 2.1.1 created: October 2014 in Nieuw-Vennep.
Publisher
Managing Editor
Technical Editors
Cover Design
Inepro B.V.
K. de Graaf
P. Blom
K. de Graaf
Production
Inepro B.V.
Team Coordinator
R. Groen
H. Wagenaar
Inepro IP Reader V2
R. de Koker
Inepro IP Reader V2
http://www.inepro.com
Table of Contents
Introduction 2
Components 4
Operating Procedures 8
Network Connections 10
LEDs (Light Emitting Diodes) 14
Hardware installation 20
Software configuration settings 26
Specifications 32
Appendix I 38
ATTENTION!!
Read this manual carefully before installing the IP Reader!
Mains connection
Guarentee
Security
Before connecting the appliance to the mains, check that the mains supply voltage corresponds
to the voltage printed on the type plate of the adapter. If the mains voltage is different, consult
your supplier.
No guarantee can be given if safety regulations are not followed.
Always disconnect the power supply before handling anything inside the device.
This device is in conformity with the EMC directive and low-voltage directive.
CE Conformité Europeène (Conform European Norm)
End of life directives
Inepro is paying a lot of attention to environmentally-friendly production. Your new device contain
materials which can be recycled and reused. At the end of its life specialised companies can
dismantle the discarded device to recycle the reusable materials and to minimise the amount of
materials to be disposed of. Please observe the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
This device may only be used indoors.
Indoor User Only
Directives
Version 2.1.1 - I
I
Introduction
Part
2 - Inepro IP Reader V2
Introduction
In this manual you find the instructions to install and configure your
IP-reader. This manual is meant for all the Inepro IP-readers.
This manual, the IP reader hardware and software are subject to
change, make sure you have the latest version of this manual,
because the older versions may have become obsolete.
Function
The purpose of the IP reader is to read the unique ID contained in
the card that is presented to the reader and transfer this ID to a
server. In most cases this data will be the card serial number. To
facilitate this a variety of card reader software module have been
developed. Our configuration tool will enable you to change the
setting on the IP reader board.
Inhaltsverzeichnis
Andere Inepro Kartenleser Handbücher
Inepro
Inepro Spider RFID Reader Bedienungsanleitung
Inepro
Inepro IP Card Reader Bedienungsanleitung
Inepro
Inepro SCR808 Bedienungsanleitung
Inepro
Inepro SCR708 Bedienungsanleitung
Inepro
Inepro MagStripe - PayCon II Bedienungsanleitung
Inepro
Inepro Spider Desktop Bedienungsanleitung
Inepro
Inepro IP Card Reader Bedienungsanleitung
Inepro
Inepro Reader Bracket for MFP Bedienungsanleitung
Inepro
Inepro IP Card Reader Bedienungsanleitung
Inepro
Inepro 276001 Bedienungsanleitung
Beliebte Kartenleser Handbücher anderer Marken
Rosslare
Rosslare DR-6255 Bedienungsanleitung
Lindy
Lindy 51541 Bedienungsanleitung
Diapro T?bbi Ürünler
Diapro T?bbi Ürünler Across System Bedienungsanleitung
Johnson Controls
Johnson Controls Kantech tyco ioSmart Bedienungsanleitung
ACS
ACS ACR122L Bedienungsanleitung
Secukey
Secukey S2-MF Bedienungsanleitung
