Infaco A3M V2.0 Installations- und Betriebshandbuch

INSTRUCTIONS FOR USING THE

A3M V2.0 12V TYING MACHINE:

SAFETY INSTRUCTIONS ______________________________________________ 4

GENERAL PRESENTATION ____________________________________________ 5

USING YOUR MACHINE FOR THE FIRST TIME __________________________ 6

CARRYING THE MACHINE ___________________________________________ 6

SWITCHING ON _____________________________________________________ 7

LOADING THE REEL__________________________________________________ 8

REMOVING THE REEL ______________________________________________ 10

USER GUIDE _______________________________________________________ 11

RECHARGING THE BATTERY ________________________________________ 13

DAILY MAINTENANCE ______________________________________________ 16

ANNUAL MAINTENANCE ___________________________________________ 16

OPERATING PROBLEMS ____________________________________________ 17

SAFETY INSTRUCTIONS ___________________________________________ 21

APPROPRIATE TYING METHOD ______________________________________ 22

GUARANTEE CONDITIONS _________________________________________ 24

GUARANTEE COUPON ______________________________________________ 29

SPECIFICATIONS __________________________________________________ 31

DECLARATION OF CONFORMITY_____________________________________ 32

Contents

Keep all safety warnings and instructions so that you can refer to them at

a later date.

The term “tool” in the warnings refers to your electrical tool run off the main

supply (with supply power cord) or your electrical battery-operated tool (without

a supply power cord).

WARNING. Read all safety warnings and all instructions. Failure to

abide by warnings and instructions could lead to an electric shock, ﬁre

and/or serious injury

ENVIRONMENTAL PROTECTION

Follow the speciﬁc instructions for waste elimination in your

country. Electrical appliances should not be thrown in the garbage.

The device, accessories and packaging should be recycled.

Ask your specialist INFACO retailer for the latest information on

eco-compatible waste elimination.

SAFETY INSTRUCTIONS

GENERAL PRESENTATION

01. TOOL CARY BAG

02. INSTRUCTIONS FOR USE

03. 12VOLT BATTERY POUCH

04. 12VOLT BATTERY CHARGER

05. PINCERS

06. GREASE SPRAY

07. A3M V2 MACHINE

08. TYING HEAD UNLOCKING KEY

09 . TYING HEAD

10 . ADJUSTMENT WHEEL

Adjusts the number of turns: 3 to 6 twists.

11 . MULTIFUNCTION CONTROL SWITCH

Short pressure = controls the blade only.

Sustained pressure = controls the tying cycle.

12 . LEVER

Used to activate a roller system to prevent the wire

from moving backwards.

13 . REEL OF WIRE

Wire available in Ø 0.40 / 0.46/ 0.50 mm.

14 . 12Volt SUPPLY CABLE

BEFORE USING YOUR MACHINE FOR THE FIRST TIME

CARRYING THE MACHINE

Attach the belt 01 around your waist.

Place the battery on your stomach side.

In wet weather, the battery belt must be worn under waterproof clothing to keep the bat-

tery unit dry.

Please read these instructions carefully before using the machine.

We strongly recommend that you ask for assistance from your retailer, who is

authorised to give you all the advice you need to use the machine properly and

achieve a good output.

It will take a day’s use to acquire a sound knowledge of how to operate

the machine.

Charger the battery for at least 3 hours before starting your ﬁrst day’s work.

(See chapter P9 battery recharge).

Disconnect the machine from its battery for all operations apart from tying.

Always keep your hands well away from the tying head when the machine is in

operation.

We strongly recommend that, for safety and practical reasons, you use the case

provided for carrying the machine and the battery in the workplace.

01 . ELASTIC BELT WITH VELCRO

02 . STORAGE POCKETS (reel, tools, etc.)

03 . TOOL CARY BAG

The tying head should be in the working position before switching on.

Connect the battery exit cable 01 to the machine supply cable 02.

The machine is switched on.

Short pressure on the switch 03 will control only the wire cutting function (zone 04).

Sustained pressure will launch the complete tying cycle (See chapter “Making a tie”).

01 02

CORRECT INCORRECT

SWITCHING ON

6 7

The wire needs to be prepared to make it easier to feed through

the machine.

Cut the end to obtain a wire with no

bends in it.

Clip the lever 01 upwards.

01 02

Smoothe the wire for at least 40 cm.

Clip the reel on to the machine

between cheeks 01 and 02.

LOADING THE REEL

Insert the wire into hole 01. Keep on feeding the wire through

until it emerges from the tying head 01.

If you come up against an obstacle

during insertion, move the wire gent-

ly backwards and forwards and/or

press once or twice the control switch

to pivot the tying head and to keep

the wire moving through the ma-

chine.

IF THE WIRE STILL DOESN’T COME

OUT: we recommend that you dis-

connect the tying head (See chapter

“Operating problems” P16), check

that the wire isn’t stuck and try to in-

sert it with the head removed

Unclip the brake system lever 01.

At the start of each reel, check

that the wire is properly rolled and

doesn’t stick between cheeks 02 and

03.

Switch the machine on and press

brieﬂy on the control switch to cut

the excess wire.

You can now start tying operations.

8 9

REEL WITH REMAINING WIRE

EMPTY REEL

REMOVING THE REEL

Clip lever 01 upwards to allow the

wire free movement through the

passage

Pull directly on the reel to unclip it from

the machine.

Pull the reel to unclip it from the

machine

Carry out a visual check on wire exit

01 to ensure that there is no wire

remaining in the machine.

After the last tying operation it is

possible that some wire may remain

stuck in the tying head:

• If it does not prevent you from loa-

ding another reel, carry on working.

It will come out during tying, usually

without a problem.

• If it does prevent you from feeding

a new wire through, disconnect the

head and remove the remaining

wire by hand (See chapter “Solving

operating problems”).

Andere Handbücher für A3M V2.0

Inhaltsverzeichnis

Andere infaco Elektrowerkzeuge Handbücher

infaco

infaco Electrocoup F3015 Bedienungsanleitung

infaco

infaco Electrocoup F3015 Bedienungsanleitung

infaco

infaco A3MV2-12V Bedienungsanleitung

infaco

infaco E5000 12V Bedienungsanleitung

infaco

infaco Powercoup PW2 Bedienungsanleitung

infaco

infaco EC1700 Bedienungsanleitung

infaco

infaco Powercoup PW2 Bedienungsanleitung

infaco

infaco A3MV2-48V Bedienungsanleitung

infaco

infaco Powercoup PW2 EC1700 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung

infaco A3M V2.0 Installations- und Betriebshandbuch

Beliebte Elektrowerkzeuge Handbücher anderer Marken