Infineon TRAVEO T2G Bedienungsanleitung

User Guide Please read the Important Notice and Warnings at the end of this document 002-32910 Rev. *A

www.infineon.com page 1 of 25 2021-09-29

Getting started with TRAVEO™ T2G entry family

starter kit

About this document

Scope and purpose

This document explains how to set up and use TRAVEO™ T2G body entry family starter kit. The document also

explains how to debug with a single core and dual core environment in IAR embedded workbench for Arm®

(EWARM). The document uses the TRAVEO™ T2G body entry starter kit board with the sample driver library

(SDL).

Intended audience

This document is intended for software and hardware engineers integrating TRAVEO™ T2G body entry device

into their application.

Abbreviations and definitions

Table 1 Abbreviations

Abbreviations

Description

CM0+

Arm® Cortex®-M0 plus

CM4

Arm® Cortex®-M4

SDL

sample driver library

starter kit

USB

universal serial bus

EWARM

embedded workbench for Arm®

C-SPY

high level debugger language for embedded system

Reference documents

[1] KitProg3 user guide

[2] TRAVEO™ T2G starter kit user guide

User Guide 2 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

Table of contents

About this document....................................................................................................................... 1

Table of contents............................................................................................................................ 2

1Getting started ...................................................................................................................... 3

1.1 Connection setup....................................................................................................................................3

1.2 Power up..................................................................................................................................................3

1.3 Installing kit driver ..................................................................................................................................4

2SDL and IAR EWARM setup....................................................................................................... 6

2.1 SDL environment setup...........................................................................................................................6

2.2 IAR EWARM setup.....................................................................................................................................6

2.3 Verify installation by quick hands-on.....................................................................................................7

3Download and debug with starter kit ....................................................................................... 9

3.1 Debugging with single core CM0+ workspace......................................................................................10

3.2 Debugging with single core CM4 workspace........................................................................................14

3.3 Debugging with dual core CM0+ and CM4 workspaces........................................................................18

4Troubleshooting ...................................................................................................................23

4.1 Connection troubleshooting.................................................................................................................23

4.2 Driver troubleshooting..........................................................................................................................23

4.3 Debugger troubleshooting....................................................................................................................23

4.4 Key points..............................................................................................................................................23

Revision history.............................................................................................................................24

User Guide 3 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

Getting started

1Getting started

This section explains the hardware setup. Table 2 lists the prerequisites for the setup.

Table 2 Prerequisites

Quantity

Description

Remarks

CYTVII-B-E-1M-SK

TRAVEO™ T2G body entry series starter kit

Micro USB cable

For power and communication

With USB port

IAR EWARM 8.42.1

Downloaded from the web

Sample driver library v7.0.0

Downloaded from the web

Firmware

Pre-installed

1.1 Connection setup

Connect the USB cable from the PC to the starter kit. The starter kit is powered by the PC via the USB cable

(5 V). Check if the mode LED (LED3) and the power LED (LED2) are turned ON.

Figure 1 Connection between PC and starter kit

1.2 Power up

When powered ON, the device will start executing the pre-installed firmware, which is indicated by the blinking

user LEDs (LED1 is controlled by core Arm® Cortex®-M0+ (CM0+) and LED4 is controlled by core Cortex®-M4

(CM4)).

User Guide 4 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

Getting started

Note: To indicate that the starter kit is powered ON and the USB controller is starting in the correct

mode, the amber-colored status LED3 must be permanently ON. But, LED3 does not indicate a

successful USB driver installation.

Figure 2 LED indicating power ON

1.3 Installing kit driver

To work with the starter kit, the KitProg3 USB-UART driver must be installed on the system. This driver is part of

a firmware package and must be installed manually. Optionally further information about KitProg3 see [1].

To install the KitProg3 USB-UART driver, do the following steps:

1. Download firmware-loader package

2. Extract the package.

3. Depending on your operating system, browse fw-loader\bin\drivers\KitProg3\KitProg3UART.

4. Right-click the file “KitProg3UART.inf”and execute “Install”. Then the driver is being installed.

Confirm that the starter kit is recognized as a KitProg3 device on Windows (open Device Manager, follow the

menu path View > Devices by container) as shown in Figure 3. This completes the hardware setup.

Figure 3 Viewing KitProg3 driver in Device Manager

User Guide 5 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

Getting started

Note: Do not press SW3. Pressing SW3 changes the mode of the USB controller. This is necessary only for

upgrading the USB driver firmware and other activities. For more details, see the KitProg3 user

guide [1].

For more information related to the starter kit, see the TRAVEO™ T2G starter kit user guide [2].

User Guide 6 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

SDL and IAR EWARM setup

2SDL and IAR EWARM setup

This section explains how to run an example from the SDL on the TRAVEO™ T2G starter kit using the IAR C-SPY

debugger.

2.1 SDL environment setup

Download the latest SDL for the TRAVEO™ T2G starter kit on the target system. Install the SDL outside the

default program files to allow the IDE to access and create temporary files. Figure 4 shows the sample path.

Figure 4 SDL 7.0.0 top-level directory

2.2 IAR EWARM setup

Open the Readme.pdf from the root folder of the SDL and use the same link to download the version of IAR

EWARM supported by the SDL.

Download the software and run the installation (note that the installation might take some time). When you

open the IAR EWARM for the first time, select the license in the License wizard. If you do not have the license, it

is strongly recommended to register for a Code size limited license type. See Figure 5.

Note: IAR EWARM v8.42.1 is only for reference; always use the IAR EWARM version supported by the

specific SDL release.

User Guide 7 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

SDL and IAR EWARM setup

Figure 5 Registering IAR for evaluation (based on v. 8.42)

2.3 Verify installation by quick hands-on

The starter kit is now ready to use after a successful environment setup (USB driver installation, SDL

installation, and IAR installation). To verify the installation and setup is complete, quickly walkthrough the

following steps:

1. Connect the USB cable from the PC to the starter kit, LED2 and LED3 should be ON.

2. After power-up, LED1 and LED4 will start blinking from the pre-installed firmware on the kit.

3. Start IAR EWARM and open the SDL template workspace file:

tviibe1m\tools\iar\flash\tviibe1m_flash_cm0plus_template

4. Select the workspace revision starter_kit from drop-down list under Workspace.

5. Click Project from top menu and select Rebuild All.

6. Check for the successful build from the Build tab at the bottom left corner in IAR window.

7. The kit is already running a pre-installed firmware on it so we can connect to target CPU (TRAVEO™ T2G) by

selecting Attach to Running target option from the Project menu.

8. The debug log shows the interface and device information in the Debug tab at the bottom left corner.

9. Click pause to check the CPU execution, LED1 will stop blinking due to the pause action.

10. Now click the stop debugging button to detach the target.

11. Close the IAR window and reset the starter kit using switch SW2.

Note: In case of problems, see Troubleshooting.

User Guide 8 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

SDL and IAR EWARM setup

Figure 6 Build a workspace in IAR

Figure 7 Check debugger and kit connection in IAR

User Guide 9 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

Download and debug with starter kit

3Download and debug with starter kit

There are two debugging methods with IAR EWARM:

•Debugging with code downloaded on to RAM

•Debugging with code downloaded on to the flash memory (described in this document)

SDL supports three types of workspaces under flash memory debugging as listed in Table 3.

Table 3 IAR Flash workspaces and functions

Workspace

Application

core

Number of

cores supported

Details

Single core CM0+ workspace

“tviibe1m_flash_cm0plus_template”

Single

Single core download and

debug for CM0+ core.

Single core CM4 workspace

“tviibe1m_flash_cm4_mc_template”

Yes

Single

Single core download and

debug for CM4 core; works as

client/slave workspace in

multicore configuration.

Note: It is possible to

debug only with

CM4, when CM0+

executes some

code, thus

enabling CM4.

Dual core CM0+ and CM4 workspace

“tviibe1m_flash_cm0plus_cm4_template”

Yes

Dual

Dual core download and debug

for CM0+ and CM4 cores; works

as master workspace in

multicore configuration.

Note: Both CM0+ and CM4 can do normal code execution, but from an architectural point only CM4 is

considered as the application core. After a reset, the default core is always the CM0+ core. To

enable the CM4 core, CM0+ must call Cy_SysEnableApplCore (). In the SDL, this is usually done

within main_cm0plus.c.

Before downloading and debugging with the multicore master project, you must build the multicore slave

project for the application core (which is CM4 here).

Open the master workspace (dual core CM0+ and CM4 workspaces) for multicore debugging. The slave

workspace (single core CM4 workspace) will automatically open from the master workspace when you click

Download and Debug.

User Guide 10 of 25 002-32910 Rev. *A

2021-09-29

Getting started with TRAVEO™ T2G entry family starter kit

Download and debug with starter kit

3.1 Debugging with single core CM0+ workspace

1. Start IAR EWARM and open the SDL template workspace file:

tviibe1m\tools\iar\flash\tviibe1m_flash_cm0plus_template

Figure 8 Selecting CM0+ single core template

2. Select the workspace revision starter_kit from the drop-down list under Workspace, as shown in

Figure 9.

Note: Ignore other workspace revisions for this starter kit. The other revisions constitute the MCU

assembled on other evaluation boards (CPU board).

Andere Handbücher für TRAVEO T2G

Inhaltsverzeichnis

Andere Infineon Computerhardware Handbücher

Infineon

Infineon REF-Vacuum-C101-2ED Bedienungsanleitung

Infineon

Infineon TLD5501-2QV Buck Demo Bedienungsanleitung

Infineon

Infineon TLE4241SYS SHIELD Bedienungsanleitung

Infineon

Infineon XMC1400 Bedienungsanleitung

Infineon

Infineon SPI F-RAM FM33256B Bedienungsanleitung

Infineon

Infineon AIROC CYW9 907 Series Bedienungsanleitung

Infineon

Infineon BTN9960 Bedienungsanleitung

Infineon

Infineon R 48V BATT Switch10 Bedienungsanleitung

Infineon

Infineon TRAVEO T2G Bedienungsanleitung

Infineon

Infineon Traveo II CPU board Bedienungsanleitung

Infineon

Infineon CY8CPROTO-062S2-43439 Bedienungsanleitung

Infineon

Infineon TLE493D-P2B6 MS2GO Bedienungsanleitung

Infineon

Infineon OPTIREG TLS850A4TEV50 Bedienungsanleitung

Infineon

Infineon CY8CKIT-028-SENSE Bedienungsanleitung

Infineon

Infineon EASY3452 Bedienungsanleitung

Infineon

Infineon EVAL-XMC4800PSOC6M5 Bedienungsanleitung

Infineon

Infineon CY8CKIT-005 Bedienungsanleitung

Infineon

Infineon EZ-PD PMG1 Bedienungsanleitung

Infineon

Infineon AN230264 Bedienungsanleitung

Infineon

Infineon BTS3011TE Bedienungsanleitung

Infineon

Infineon CYSBSYSKIT-DEV-01 Bedienungsanleitung

Infineon

Infineon Cypress S6SATU01A Series Bedienungsanleitung

Infineon

Infineon Cypress CY8CKIT-064B0S2-4343W Bedienungsanleitung

Infineon

Infineon AURIX TC 4 Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung