Infineon TDA7210V Bedienungsanleitung

Kit Content

TDA7210V Remote Control Rx-Board

Design Example by Mipot S.p.A.

Dear Customer,

Thank you for working with Infineon Wireless Control products!

This TDA7210V Remote Control Receiver-Board represents a typical design example

how the TDA7210V can be used as a receiving component in a remote control

application. On the side of the TDA7210V there is a microcontroller decoding the

received signal and driving the five output channels. This design is fully compatible to

Infineon’s PMAfob remote control transmitter (see

www.infineon.com/PMAfob

All design information is available for download on the Infineon internet pages

(see

www.infineon.com/TDA7210V



Schematic



PCB layout



Components list



Microcontroller firmware (C source code)

The TDA7210V Remote Control Rx-Board was designed by one of Infineon’s

recommended design houses for Wireless Control products:

Mipot S.p.A. (

www.mipot.com

)

For further support please contact your local Infineon Distributor, your responsible

Infineon Sales Office, contact us directly at

wirelesscontrol@infineon.com

or call us

0(0)800 951 951 951.

This is an international toll free phone number. In case this

service is not supported in your country, you can find a complete list of Infineon

service phone numbers at

www.infineon.com/customercarecenter

Please, don’t forget to take notice of the legal disclaimer sheet.

We wish your development work using Infineon’s Wireless Control products will be

successful.

Your Infineon Wireless Control Team

www.infineon.com/TDA7210V www.infineon.com/PMAfob



TDA7210V Remote Control Rx-Board



PMAfob Remote Control Transmitter



1 antenna, ¼ lambda - reduced size



Legal disclaimer sheet

Firmware source code and Hardware

design documentation available

for download at

www.infineon.com/TDA7210V



TDA7210V_RC_RxBoard_vx.y.zip

Other available PMAfob demos:



PMAfob RKE demonstrator



PMAfob Home Automation

demonstrator

September 2010

Read Me First

TDA7210V Remote Control Rx-Board

Step-by-Step Quick Start Guide

Please follow this step-by-step approach when you start up your TDA7210V

PMAfob remote control demo for the first time:



Check the placement of all jumpers on the board. By default the jumpers marked

MSEL and CSEL must be in closed position. The power down mode selection jumper

marked PWRDWN must be closed in position +V. All other jumpers or test pins on

the board must be left in open position (except the power supply selection jumper

5V/7-15V – see below). See the picture on the right where all closed jumpers are

marked.



Connect the antenna to the SMA-connector marked RF IN. This application operates

in the 434 MHz frequency band. Therefore, antennas with red marking are suitable.



Connect a suitable power supply to the TDA7210V Remote Control Rx-Board. There

are two alternatives:



Regulated: Connect a regulated DC supply voltage of +5.0V to the screw

terminals marked GND and 5V. In this power supply mode the related

jumper must be placed in position 5V.



Unregulated: Connect an unregulated DC supply voltage in the range

between 7.0V and 15.0V to the screw terminals GND and 7-15V. In this

power supply mode the related jumper must be placed in position 7-15V.



Switch on the power supply.



Press button S1 to activate the receive mode. LEDs DL1 and DL2 will signalize the

receive-ready state.



Upon delivery of the kit the enclosed PMAfob remote controller is already set to the

correct protocol mode for this demo. By pressing buttons on the PMAfob related

channel LEDs (CH1…CH5) on the TDA7210V Remote Control Rx-Board will change

their state.

Note: The PMAfob remote controller supports different protocol modes. This demo

requires the mode XTEA-Frame/no encryption which is already configured upon

shipment of the kit. The protocol mode may be changed by removing the battery from

the PMAfob or accidently by holding buttons down longer than 3 seconds. In case your

TDA7210V Remote Control Rx-Board does not react to any remote control commands

anymore, follow these steps to reactivate the right protocol mode:



Open the PMAfob housing and remove the battery for longer than 5 seconds. Re-

insert the battery again.



Hold down button CH5 for longer than 3 seconds.



Hold down button CH4 for longer than 3 seconds.



Now, protocol mode XTEA-Frame/no encryption is re-established and the demo shall

operate as expected.

Find more information about PMAfob protocol modes in the PMAfob User Guide.

Early versions of PMAfob delivered with other kits may not support the protocol mode

XTEA-Frame/no encryption. These may be re-programmed with newest PMAfob

firmware (see

www.infineon.com/PMAfob

) for full compatibility with all applications.

Quick Start

Antenna Colour Coding



Green: 315 MHz



Red: 434MHz



White: 868 MHz



Yellow: 915 MHz

2010

Andere Infineon Mikrocontroller Handbücher

Infineon

Infineon PG-TO252 DPAK Bedienungsanleitung

Infineon

Infineon XMC7000 Series Bedienungsanleitung

Infineon

Infineon PSoC 4000 Series Produkthandbuch

Infineon

Infineon AIROC CYW20829 Bedienungsanleitung

Infineon

Infineon Lite SBC Series Bedienungsanleitung

Infineon

Infineon CY8CKIT-062-WIFI-BT Bedienungsanleitung

Infineon

Infineon AIROC CYW20829 Bedienungsanleitung

Infineon

Infineon XMC7000 Series Leitfaden

Infineon

Infineon XMC4000 series Bedienungsanleitung

Infineon

Infineon XMC4000 series Bedienungsanleitung

Infineon

Infineon XE166 Series Bedienungsanleitung

Infineon

Infineon NGC1081 Bedienungsanleitung

Infineon

Infineon XC800 Series Bedienungsanleitung

Infineon

Infineon PSoC 6 Bedienungsanleitung

Infineon

Infineon XMC Series Benutzerhandbuch

Infineon

Infineon Cypress PSoC 4500S Pioneer Kit Bedienungsanleitung

Infineon

Infineon PSoC 4 Bedienerhandbuch

Infineon

Infineon C166 Series Montage- und Bedienungsanleitung

Infineon

Infineon MOTIX TLE985xQX Bedienungsanleitung

Infineon

Infineon XMC1400 Bedienungsanleitung

Infineon

Infineon TRAVEO T2G Produkthandbuch

Infineon

Infineon XC164 Series Montage- und Bedienungsanleitung

Infineon

Infineon XMC4000 series Bedienungsanleitung

Infineon

Infineon XC800 AP08113 Montage- und Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung