Infinite L-COM SRAQ-G014 Bedienungsanleitung

FLAMMABLE GAS SENSOR MODULE

User Guide for SRAQ-G014

Thank you for choosing L-com product. To ensure safe, accurate performance and product longevity, please take a moment to familiarize yourself

with this manual before powering the device. Please keep it handy for future reference. In case of any questions regarding the installation or use of

product, please call us at 800.341.5266.

Reach out to us at customerservice@l-com.com and visit our website at www.l-com.com

M_L-com_SRAQ-G014_11/2022_R1.0

Product Description

The SRAQ-G014 gas sensor module detects the presence and concentration of flammable gases such as butane, propane, methane and hydrogen.

Integrated circuitry produces a non-linear voltage signal corresponding to the gas concentrations. The SRAQ-G014 has high sensitivity and can detect

flammable gas concentration in the range of 50 to 10000 ppm and also carbon dioxide from as little as 10 ppm to as much as 1000 ppm.

Features

 Features MQ9 sensing element

 Highly sensitive to CO, CH4, LNG

 Analog and TTL level outputs

 Indication light

 4 pin male header

Applications

 HVAC gas leakage alarm

 Industrial combustible gas alarm

 Portable flammable gas detector

 Integration into air quality monitoring devices

Technical Parameters

Electrical Diagram

 VCC is the 0  5 VDC power supply positive and negative; GND is the ground

 Aout is the analog output, Dout is the level output

 On the PCB, Indicator light on: Dout is low level. Indicator light off: Dout is high level

 The 1k resistor shown on the PCBA is the load resistance (RL), it can be changed by user. Due to the sensor itself the load resistance range

should be 100k  1M.

Mounting Diagram

Mount the PCBA to the enclosure with screws. Hole diameter 3mm, pitch distances as per the diagrams given below.

Working Voltage 5 VDC ± 0.2 V

Working Current <150 mA

Gas Detection Flammable Gas, CO

Detection Concentration 50  10000 ppm (Flammable gas), 10  1000 ppm (CO)

Preheating Time >30 mins

Response Time ≤1 sec

Recovery Time ≤30 sec

Output Mode

Aout (Analog signal) 0  5 V (non-linear)

Dout (Level signal) Low level: 0V; High level: 3.7V

Work environment

Temperature -10~50 °C

Humidity ＜95% RH

Notes

1. Confirm the polarity and the voltage of the power supply before powering ON the sensor.

2. The analog output of this module is non-linear. When connect to microcontroller, it should be connected to ADC interface of the microcontroller.

3. The relationship between the resistance ratio and the concentration is a logarithmic relationship. For more info on typical sensitivity curve, check

MQ9 Probe on internet.

Typical Sensitivity Curve

Temperature: 20 °C

Humidity: 65%

Oxygen: 21%

RL = 10 kΩ

Rs: Resistance in various concentration value of gas

R0: Resistance in 1000 ppm LPG

The calculation of the resistance ratio according to the output voltage is as follows:

The sensor is energized in relatively clean air for more than half an hour and after measure the output voltage value of Aout.

VCC is the power supply voltage, 5 VDC

RL is the load resistance

VRL = Aout = Vair value

When the sensor detects gas, the RS value can be calculated after measuring the value of Aout.

The VRL value at this time is the Aout value after gas is detected. It is different from the value of the above formula. The VCC value and the RL value

are the same as above.

The R0 and RS values are obtained, and the specific concentration value of the gas is converted by the RS / R0 value of the Sensitivity Characteristic

Curve.

Inhaltsverzeichnis

Andere Infinite Steuereinheit Handbücher