Infinity Club 1200 Bedienungsanleitung

INFINITY Club 1200

Professional 1200W discharge scan-light

USER’ S MANUAL release 1.0

This manual must be considered an integral part of the projector.

BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE

INSTRUCTIONS IN THIS MANUAL.

QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE

INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.

BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE

VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.

FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:

[email protected]

INDEX

GENERAL DESCRIPTION ---------------------------------------------------------------------------- page 2

DESCRIPTION OF PARTS AND CONTROLS -------------------------------------------------- page 3

START-UP PROCEDURES -------------------------------------------------------------------------- page 5

DMX CHANNEL ASSIGNMENT -------------------------------------------------------------------- page 8

OPTICAL SYSTEM ------------------------------------------------------------------------------------ page 12

TROUBLESHOOTING -------------------------------------------------------------------------------- page 12

MAINTENANCE ---------------------------------------------------------------------------------------- page 13

SPARE PARTS ----------------------------------------------------------------------------------------- page 15

WARRANTY --------------------------------------------------------------------------------------------- page 15

GENERAL DESCRIPTION

As shown in Figure, the INFINITY CLUB 1200 is made up of the following parts:

1. Rear panel

2. Cooling unit

3. Auxiliary support

4. Anchoring bracket

5. Lamp compartment

6. Lid

7. Projector body

8. Swivelling head

9. Rotating mirror

Technical Features and Dimensions

Voltage rating 230 V

Rated current 7,5 A

Induced current 3,5 A

Absorbed power 1600 W

Frequency 50 Hz (60 Hz optional setting)

Maximum room temperature 35º C

Maximum surface temperature 70º C

Distance from inflammable surfaces 1,5 m

Main assembling via #1 screw M 12

Auxiliary device mount via #1 screw M 12

Length 1070 mm

Width including bracket and handle 440 mm

Weight 40 Kg

Weight, including packaging 47 Kg

CAUTION

The projector cannot be mounted on inflammable surfaces.

Norms applied to construction:

EN 60 598-1 EN 60 598-2-17 EN 294 EN 50 082-1

EN 55 015 EN 60 555-2 EN 61 000-3-2

DESCRIPTION OF MOVING PARTS AND CONTROLS

Rear Panel

As shown below, the following elements can be seen on the rear panel:

1. Cable clamp, (cable 1m)

2. ON/OFF switch

3. Line fuse

4. Electronic fuse

5. CANNON 3 pin socket and jack area

6. DMX address area

7. Personality functions area

8. Serial number plate

9. Rear handles

Adjustment of Projector Body Angle

As shown in Figure, the INFINITY CLUB 1200 projector can be adjusted between 0 ÷ 50° compared to its

anchoring bracket.

- Loosen lateral knobs.

- Place the projector at the desired angle.

- Firmly tighten lateral knobs.

- Make sure the projector is correctly mounted at the new angle.

Working Position

INFINITY CLUB 1200 can work in all positions within ± 90° of the horizontal axis.

Admissible Environmental Conditions

The projector was engineered and produced to function in covered, dry areas with an air temperature ranging

between 5° and 35° C, and with a humidity level between 30 and 90%.Sharp changes in room temperature may

generate condensation inside the projector, which can harm the projector. Therefore, switch on the projector only

after it has undergone a period of gradual adaptation to the room temperature.

Mechanical Safety Guards

A bipolar cut-off switch is located between the lamp compartment and the cooling unit. This safety switch cuts off

the power to the projector if the top lid is opened.

Noise Level

After the projector has been powered up and the initial configuration takes place, the noise produced by the

projector is primarily due to its cooling system. The noise level is much lower than the limit of 70 dB permitted by

law.

Adjustment of Mirror Support Angle

As shown in the picture, the mirror support can rotate on a 340° angle (+170° / -170°).

Loosen knob “A”.

Rotate the projector head to the desired angle.

Firmly tighten knob “A”.

Modular construction

As shown in the picture, the INFINITY has a modular construction for ease maintenance. (MSZ in the picture)

HANDLE WITH CARE!!!

Loosen the knobs of the top lid and remove it.

Loosen the lateral screws of module to remove it.

The modules have easy and direct connection system.

Packing

The projector is shipped and delivered in a cardboard box made of KRAFT cardboard and semi-chemical additive-

free paper, in compliance with BSFV Class 3 standards for waste disposal. The projector is completely assembled,

placed in the box inside a polyethylene bag and held firmly in place with polyurethane foam packing material. The

box is stapled shut. Even though the packing provides complete protection from rain, it must not be exposed to

inclement weather or humidity.

No more than three identical boxes can be stacked one on top of the other.

Keep the original packing for possible shipments in the future.

Storage

The projector, in its original packing, must be kept in covered, dry areas with a temperature between -10° C and

+50° C.

Handling

The projector, with or without packing, must be handled with care. Lifting and handling must be carried out with

special equipment. Do not expose the projector, with or without its packing, to brusque accelerated or decelerated

movements, knocks, dragging, or other stress caused by unsuitable handling methods.

The projector in its packing can be seriously damaged if it falls or suffers a blow during transportation.

START-UP PROCEDURES

Positioning and Installation

Follow these steps for opening the package and installing the projector on its working position:

· Place the projector near the place it will be installed.

· Open the package and remove anchoring elements and accessories.

· Carefully read the instructions in the manual.

· Prepare suitable hooks for the anchoring brackets and auxiliary support.

· Using suitable lifting equipment, place the projector up against the hooks.

· Tighten the M12 bolts and insert a device to prevent them from accidentally loosening.

· Attach the auxiliary support element and make sure it is tightly fastened.

· Make sure all adjustable parts are locked firmly in place in the desired position.

CAUTION

You must verify the stability of the anchoring elements when the projector is in working condition. In compliance

with the laws in force, the anchoring support must withstand a load of 400 kg. Screws, hooks, and hardware must

be inserted correctly and installed to prevent them from accidentally loosening.

IMPORTANT

The projector was designed to function when attached to the bracket. The projector cannot function sitting upon a

flat surface that obstructs the rear cooling vents. Do not install the projector where there are objects located at a

distance of less than 20 centimetres from the cooling system.

Lamp installation

• Loosen the knobs on the top lid and remove it.

• Remove the lamp from the packing and carefully read the

manufacturer’s instructions.

• LAMP MSR/HSR 1200W or MSD/HSD 1200W: Insert the lamp

into the ceramic socket (G22).

• LAMP HMI/MSI 1200W: Loosen the two ring nuts at both end

of the lamp (socket SFc15-5).

Place the lamp in its socket. Make sure the protuberance of the

central bulb is facing downwards to avoid creating shadows in

the projection. Tighten the two ring nuts on the lamp.

• Replace the top lid and firmly tight the knobs.

• Regulate the LAMP, with screws, if necessary.

CAUTION

During lamp installation and substitution, the operator must take care to avoid any contact between the lamp bulb

and the condenser lens. (The condenser lens is a special tempered glass, very resistant to the high temperature

but very fragile in case of contact with quartz glass)

Power Supply

INFINITY 1200 absorbs 1600W at 230V. Makes sure the projector does not pull the cable in all different working

positions.

Connect the fixture to the mains with the enclosed power cord. See the table for the colours of the

connection-cable.

When in doubt, consult a qualified electrician.

Be careful with your operations. With a high voltage you can suffer a dangerous electric shock when

touching the wires! Inside the projector, the ignitor circuit have very high voltage, over 5Kv.

The User must ensure that the power supply is provided with a highly sensitive differential circuit breaker

30m/A to protect the projector from indirect contacts, and that the grounding system PE is working

properly.

Do not power the projector with a dimmer circuit

Control Unit

INFINITY CLUB can be controlled practically by all types of controllers on the market that can execute the standard

DMX 512 protocol. Controller-projector and projector-projector connections require a two-core screened cable

provided with CANNON XLR 3 pin, plugs and sockets. The ground braid on the screened cable must be connected

to just one end of the cable. The projector and cables must not be installed near overhead ducts for electrical

cables or intense magnetic fields.

Projector Address

To make sure the projector functions properly, the dip-switches in the DMX ADDRESS AREA, on the rear panel,

must be correctly configured. Keep in mind that each INFINITY CLUB 1200 occupies a minimum of 10 to a

maximum of 12 DMX channels (10 channels when it operates in the Standard Operating Mode, 12 when the

PERSONALITY dip-switch 01 is set to ON, enabling the HIGH DEFINITION 16bit function). Each projector must be

set separately on its own BASE CHANNEL (DMX starting address). The DMX starting address assignment is

obtained by summing the values for each switch in the DMX SECTION (for example, to set a projector on BASE

CHANNEL 39, you must set dip-switches 32, 4, 2, and 1 to the ON position, because 32+4+2+1=39). In the

Standard Operating Mode, this means the INFINITY CLUB 1200 will receive signals on 10 channels following the

DMX starting address, included (for example, if the projector is set on DMX=39, it will receive signals on channels

39, 40, 41, 42, 43, 44, 45, 46, 47 and 48).

Gobos replacement

As shown in the figure, it is very easy to replace gobos on the wheel. When the projector is cold, follow these

steps:

-Disconnect the power supply.

-Wait at least 20 minutes to be sure the projector components are cold.

-Loosen the knobs on the top lid and remove it.

-Choose the pattern you want to replace and delicately press on it to extract it from a fastening clip.

-Remove the gobo when it has been released.

-Choose another gobo from the special compartment inside the projector (see figure) or use standard M-size

metal gobos.

-Insert the new pattern inside the two clips and press lightly to click it into place beneath the third clip.

-Replace the top lid and firmly tighten the knobs

The same operation can be performed on all rotating gobos.

If you want to use other metal gobos:

Metal gobos: M size

Diameter: 66mm

Image diameter: 48mm

If you want to use glass or dichro gobos:

If you want to use a dichro gobos or glass gobos, using D size gobos (Diameter 53.3mm) and order the DG09520

Sagitter metal gobo ring. Use silicon to fix the dichro gobo on metal gobo ring.

DMX CHANNELS ASSIGNMENT

Ch FUNCTION

1 COLOUR

2 1° GOBOS WHEEL

3 GOBO INDEX + ROTATION

4 EFFECTS WHEEL

5 EFFECTS INDEX + ROTATION

6 DIMMER

7 SHUTTER

8 SPECIAL FUNCTIONS

9 PAN (coarse)

10 TILT (coarse)

11 2° PAN (fine) (when 16 bit HIGH DEFINITION

12 2° TILT (fine) SCANNING option is enabled)

Note: Is also available the following 16 bit option

9 PAN (coarse)

10 PAN (fine)

11 TILT (coarse)

12 TILT (fine)

To enable this function you must set in position ON the last three personality dip-switches (invert pan, invert tilt,

high definition scanning)

CHANNEL 1 = COLOUR

percent values decimal values

0 > 5.9 % WHITE 0 > 15

6.3 > 9.4 % WHITE / RED 16 > 24

9.8 > 13.3 % RED 25 > 34

13.7 > 18 % RED / YELLOW 35 > 46

18.4 > 21.6 % YELLOW 47 > 55

22 > 25.5 % YELLOW / MAGENTA 56 > 65

25.9 > 29.8 % MAGENTA 66 > 76

30.2 > 33.7 % MAGENTA / GREEN 77 > 86

34.1 > 37.3 % GREEN 87 > 95

37.6 > 41.6 % GREEN / ORANGE 96 > 106

42 > 45.9 % ORANGE 107 > 117

46.3 > 49.8 % ORANGE / BLUE 118 > 127

50.2 > 53.3 % BLUE 128 > 136

53.7 > 57.3 % BLUE / DARK BLUE 137 > 146

57.6 > 61.6 % DARK BLUE 147 > 157

62 > 65.1 % DARK BLUE / WHITE 158 > 166

65.5 % GREEN =167

65.9 % MAX FORWARDING SPIN =168

80 % MIN FORWARDING SPIN =204

80.4 > 83.9 % STOP 205 > 214

84.3 % MIN REVERSE SPIN =215

100% MAX REVERSE SPIN =255

- OPTION: PERSONALITY DIP-SWITCH N° 08 in position ON, give access to the PROPORTIONAL control of the

colour wheel, see the different colours sequence:

GREEN - GREEN/MAGENTA - MAGENTA - MAGENTA/YELLOW - YELLOW - YELLOW/RED - RED -

RED/WHITE - WHITE - WHITE/DARK BLUE - DARK BLUE - DARK BLUE/BLUE - BLUE - BLUE/ORANGE

- ORANGE - ORANGE/GREEN - GREEN

Note: Unchanged function from 168 to 255 (65.9% to 100%)

CHANNEL 2 = GOBO WHEEL

percent values decimal values

0 > 20 % GOBO 1 (OPEN) 0 > 51

20.4 > 40 % GOBO 2 52 > 102

40.4 > 60 % GOBO 3 103 > 153

60.4 > 80 % GOBO 4 154 > 204

80.4 >100 % GOBO 5 205 > 255

CHANNEL 3 = GOBO WHEEL ( INDEX and ROTATION )

percent values decimal values

0 > 60.4 % INDEXED POSITION 0 > 154

control of the indexed position of the pattern on

540° (1 and 1/2 revolution of the pattern)

60.8 % MAX FORWARD SPIN =155

77.6 % MIN FORWARD SPIN =198

78 > 82.7 % STOP 199 > 211

83.1 % MIN REVERSE SPIN =212

100 % MAX REVERSE SPIN =255

CHANNEL 4 = EFFECTS WHEEL + OPTIONAL IRIS

percent values decimal values

0 % 1 OPEN (IRIS OPEN) =0

0 > 20 % 1 OPEN (IRIS decrease from OPEN to close) 1 > 51

20.4 % 2 COL. TEMP. 3200°K (IRIS CLOSED) =52

20.8 % 2 COL. TEMP. 3200°K (IRIS OPEN) =53

21.2 > 40 % 2 COL. TEMP. 3200°K (IRIS decrease from OPEN to close) 54 > 102

40.4 % 3 COL. TEMP. 6000°K (IRIS CLOSED) =103

40.8 % 3 COL. TEMP. 6000°K (IRIS OPEN) =104

41.2 > 60 % 3 COL. TEMP. 6000°K (IRIS decrease from OPEN to close) 105 > 153

60.4 % 4 FROST FILTER (IRIS CLOSED) =154

60.8 % 4 FROST FILTER (IRIS OPEN) =155

61.2 > 80 % 4 FROST FILTER (IRIS decrease from OPEN to close) 156 > 204

80.4 % 5 MULTIFACE PRISM (IRIS CLOSED) =205

80.8 % 5 MULTIFACE PRISM (IRIS OPEN) =206

81.2 > 100 % 5 MULTIFACE PRISM (IRIS decrease from OPEN to close) 207 > 255

The projector has the slots and the software to drive the iris module, to order the iris diaphragm module:

Code GM00240B

CHANNEL 5 = EFFECTS ( INDEX and ROTATION )

percent values decimal values

0 > 60.8 % INDEXED POSITION 0 > 155

control of the indexed position of the pattern on

600° (about 2 revolution of the pattern)

61.2 % MAX FORWARD SPIN =156

77.6 % MIN FORWARD SPIN =198

78 > 82.9 % STOP 199 > 211

83.1 % MIN REVERSE SPIN =212

100 % MAX REVERSE SPIN =255

Inhaltsverzeichnis

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

Epson

Epson PowerLite 810p Bedienungsanleitung