Infinity Kappa Series perfect5.1 Bedienungsanleitung
Thank you for purchasing an Infinity Kappa Perfect component
system. Kappa Perfect components have been engineered to provide
the most accurate sonic reproduction possible. Over the years, we at
Infinity have listened to hundreds of automotive speakers and we
think these are among the finest. We hope you agree.
This manual includes information that will make your installation as
simple and trouble-free as possible. It also provides detailed technical
information that will help an experienced installer optimize speaker
placement and crossover adjustment. Please study this manual before
you begin your installation. Remember to send in your warranty
registration card, and keep your sales receipt somewhere safe in case
you need warranty service.
kappa series
perfect5.1
perfect6.1
instructions
IMPORTANT
Installation of automotive stereo components
can require extensive experience performing
a variety of mechanical and electrical proce-
dures. Although these instructions explain
how to install a Kappa Perfect component
system in a general sense, they do not
show the exact installation method for your
particular car. If you feel you may not have
the necessary tools or experience, ask your
authorized Infinity car audio dealer about
professional installation options.
WARNING
Playing loud music in your automobile can
permanently damage your hearing as well
as hinder your ability to hear traffic. We
recommend listening at low volume while
driving. Infinity accepts no liability for hear-
ing loss, bodily injury or property damage
resulting from use or misuse of this product.
A NOTE ABOUT SYSTEM PERFORMANCE
For the best performance possible, the
Kappa Perfect components should be used
with a two-channel amplifier with output
power of at least 50W RMS per channel.
The passive
crossover contains impedance-
compensating
circuitry and has been
computer-optimized for the flattest possible
frequency response with the tweeter flush-
mounted, on-axis with the listener. The
combined responses of the speakers and
passive crossover constitute a 4th-order
Linquitz-Riley
acoustic alignment and cannot
be duplicated
with any electronic crossover
currently available for car audio use.
Consequently, bi-amping a Perfect
component system with an electronic
crossover is not recommended.
SPEAKER PLACEMENT
Figures 1–4 show possible speaker place-
ments in the order of most desirable to
least desirable. Kick-panel mounting will
provide the best staging and imaging in
most vehicles.
TWEETER INSTALLATION
TWEETER
on dash
WOOFER
in factory-
door location
TWEETER
on kick panel
WOOFER
in factory-
door location
TWEETER
and
WOOFER
on kick panel
WOOFER
in factory-
door location
TWEETER
in high/forward
location on door
Fig 1 Fig 3
Fig 2 Fig 4
Figure 1.
Mounting the woofer and tweeter in
the kick panels
Figure 2.
Mounting the woofer in the door and
the tweeter in the kick panel
Figure 3.
Mounting the woofer and tweeter in
the doors
Figure 4.
Mounting the woofer in the door and
the tweeter in the dash
1
2
–
+
1
2
–
+
red
blk
Figure 5.
Surface-mounting the tweeter
Figure 6.
Flush-mounting the tweeter
- 2 -
WOOFER INSTALLATION
Figure 7.
Mounting the P5.1 or P6.1 woofer
where there is no factory speaker location.
To mount the P5.1 in factory locations, omit
the grille and grille tray.
Figure 8.
Mounting the P6.1 woofer in
standard 5-1/4" holes (in many
Japanese and American automobiles)
Figure 9.
Mounting the P6.1 woofer in
165mm holes (in many European
and American automobiles)
ELECTRICAL CONNECTIONS AND CROSSOVER ADJUSTMENTS
¤
TWEETER LEVEL
—4dB
J1 J2 J1 J2
0dB
+5dB
KPX00
J1 J2
Tweeter level
+5dB
Tweeter level
0dB
(default)
To woofer To tweeter
To amplifier
+
speaker output
J1 J2
Tweeter level
4dB J1 J2
++
Figure 10.
Connecting the speakers and the amplifier
to the crossover
J1
¤
Figure 11.
Adjust the crossover using the jumpers
provided
- 3 -
DECLARATION OF CONFORMITY
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
Lutz Uphoff
Harman Consumer International
Chateau-du-Loir, France 4/01
declare in own responsibility, that the products
described in this owner’s manual are in compliance
with technical standards:
EN 50081-1:1992
EN 50082-1:1997
20 Frequency 100 500 1k Hz 5k 10k 20k
C
dB spl
100
90
80
70
60
50
40
30
20
Deg 180
135
90
45
0
-45
-90
-135
-180
< Magnitude > Sound Pressure Level < Phase >
Kappa Perfect6.1 (flat setting)
Kappa Perfect6.1 (+5dB setting)
Kappa Perfect6.1 (–4dB setting)
SYSTEM RESPONSE CURVES
SPECIFICATIONS
System P6.1 P5.1
Frequency Response: 75Hz –23kHz, ±3dB 80Hz –23kHz, ±3dB
Power Handling: 100W RMS, 400W Peak 100W RMS, 400W Peak
Nominal Impedance: 4 Ohms 4 Ohms
Sensitivity: 90dB 89dB
Crossover Frequency: 3.5kHz, 24dB/oct. 3.5kHz, 24dB/oct.
Linquitz-Riley Acoustic Linquitz-Riley Acoustic
Thiele and Small Parameters
P6.1 Woofer P5.1 Woofer Tweeter
Revc: 3.45 3.38 3.31
Levc: 0.37 0.21 0.02
Sd: 0.0113 0.0100 0.0005
BL: 6.37 3.94 1.99
Vas: 11.43 9.29 0.0016
Cms: 630.36 654.21 44
Mms: 18.94 10.41 0.3064
Mmd: 18.25 9.84 0.3
Fs: 46.05 60.98 1370.65
Qms: 3.44 3.60 5.4
Qes: 0.465 0.87 2.19
Qts: 0.41 0.701 1.56
Top-PlateThickness: 9/32" (7.115mm) 9/32" (7.115mm) N/A
Voice-Coil Length: 9/16" (14mm) 9/16" (14mm) N/A
Voice-Coil Diameter: 1-1/2" (38.1mm) 1-1/4" (31.75mm) 1" (25.4mm)
Xmax: 1/8" (3.44mm) 1/8" (3.44mm) N/A
Mounting Depth: 2-3/4" (70mm) 2-3/8" (61mm) 1" (25.4mm)
Cut-Out Diameter: 5-1/16" (129mm) 4-5/8" (118mm) 1-3/4"
(45mm)
Infinity Systems, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA
(800) 553-3332 •FAX (516) 682-3523 •www.infinitysystems.com
© 2001 Infinity Systems, Inc. •Part No.: KAP5.1/6.1OM4/01 •Printed 4/01
20 Frequency 100 500 1k Hz 5k 10k 20k
C
Ohms
0.3
1.0
3.0
10.0
30.0 Deg 180
135
90
45
0
-45
-90
-135
-180
< Magnitude > Impedance Measurement < Phase >
Perfect6.1 System Frequency Response
Perfect6.1 System Impedance
20 Frequency 100 500 1k Hz 5k 10k 20k
C
Ohms
0.3
1.0
3.0
10.0
30.0 Deg 180
135
90
45
0
-45
-90
-135
-180
< Magnitude > Impedance Measurement < Phase >
Perfect5.1 System Impedance
Perfect5.1 System Frequency Response
2
re u ncy
100
500
1k
Hz
5k
10k
20k
0Fqe
Sound Pressure Level
dB spl
110
100
90
80
70
60
50
40
30
Deg
180
135
90
45
0
-45
-90
-135
-180
C
Kappa Perfect6.1 (flat setting)
Kappa Perfect6.1 (+5dB setting)
Kappa Perfect6.1 (–4dB setting)
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Infinity Sprecher Handbücher
Infinity
Infinity Intermezzo 4.1t Bedienungsanleitung
Infinity
Infinity Classia C205 Bedienungsanleitung
Infinity
Infinity IRS Sigma Bedienungsanleitung
Infinity
Infinity RS-4 Bedienungsanleitung
Infinity
Infinity OVTR 1 Bedienungsanleitung
Infinity
Infinity Total Solutions TSS-SAT500 Bedienungsanleitung
Infinity
Infinity Total Solutions TSS-SAT1200 Bedienungsanleitung
Infinity
Infinity Classia C255ES Bedienungsanleitung
Infinity
Infinity FUZE Pint Bedienungsanleitung
Infinity
Infinity Cascade 5 Bedienungsanleitung
Infinity
Infinity ERS 110DT Bedienungsanleitung
Infinity
Infinity Total Solutions TSS-SAT4000 Bedienungsanleitung
Infinity
Infinity Primus C25 Bedienungsanleitung
Infinity
Infinity SM-165 Bedienungsanleitung
Infinity
Infinity 1031t Bedienungsanleitung
Infinity
Infinity ENTRA POINT FIVE HTS Bedienungsanleitung
Infinity
Infinity Intermezzo 4.1t Bedienungsanleitung
Infinity
Infinity Reference 2000.6 Bedienungsanleitung
Infinity
Infinity Prelude MTS Center Bedienungsanleitung
Infinity
Infinity INTERLUDE IL40 Bedienungsanleitung
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung