Infinity Total Solutions TSS-SAT4000 Bedienungsanleitung

TSS-SAT4000

Owner’s Guide

TOTAL SPEAKER SOLUTIONS

TSS-4000

INFP1595Sat4000-OM 10/18/04 2:41 PM Page 1

2TSS-SAT4000

3Introduction

4Planning Your System

4Placement

5Installation

5Tabletop/Shelf Placement Assembly

8Wall-Mounting theTSS-SAT4000 Using

the Included Wall Bracket

9Wiring the Speaker

10 Specifications

Table of Contents

TSS-SAT4000 OWNER’SGUIDE

INFP1595Sat4000-OM 10/18/04 2:41 PM Page 2

TSS-SAT4000

(1) Satellite

Speaker

(1) Medium

Collar

(1) Pan-Head Phillips Screw

1/4-20 x 3/4"

(2) Pan-Head Phillips Screws

1/4-20 x 1"

(1) Flat-Head Phillips

Screw

1/4-20 x 1-1/4"

(6) Flat-Head Phillips

Screws

1/4-20 x 7/8"

(1) Large

Collar

(1) Allen

Wrench

(3) 1/4-20

Flat Washers (3) 1/4-20 Nuts

(1) Table Stand Plate

(1) Bottom Foot

(1) Small Collar

Part A

Part B

(2) Wall-Mount End Caps

(attached to satellite)

(1) Wall Bracket

With Wall

Bracket Cover

INTRODUCTION

InfinityTotal Solutions™

Infinity Total Solutions continues Infinity’s longstanding

commitment to accurate sound reproduction.Our proprietary

Metal Matrix Diaphragm™(MMD®) drivers,precision dividing

networks and rigid, well-braced enclosures combine to deliver

uncompromised performance in any stereo or multichannel home

theater system. In addition, these speakers are magnetically

shielded for safe placement adjacent to a television.

Unpacking the Speaker

Carefully unpack the speaker. If you suspect damage from

transit, report it immediately to your dealer and/or delivery

service. Keep the shipping carton and packing materials for

future use. Open the package and verify the following contents:

INFP1595Sat4000-OM 10/18/04 2:41 PM Page 3

4TSS-SAT4000

PLANNING YOUR SYSTEM

Before deciding where to best place your speakers, survey your

room and study Figures 1 and 2.

Figure 1. In this overhead view of a typical 5-channel installation,

satellite speakers are used to reproduce sound for the front

and surround channels.The center channel reproduces sound

and dialogue.The powered subwoofer provides bass for

effects and music.

Figure 2.This overhead view shows a typical home theater plan.

Left/right rear channels are for a 7-channel system. Center rear

channel is for a 6-channel system.

Couch

Left

Front

Channel

Left

Surround

Channel

Right

Surround

Channel

Right

Front

Channel

Center

Channel

Left

Rear

Channel

Right

Rear

Channel

Center

Rear

Channel

(above or below TV) Subwoofer

Couch

Left

Front

Channel

Left

Surround

Channel

Right

Surround

Channel

Right

Front

Channel

Center

Channel

(above or below TV) Subwoofer

PLACEMENT

NOTE: The satellite speakers can be placed directly on a shelf

using one of the three included shelf stands, or mounted on a

wall using the included wall brackets. Optional floor stands and

in-wall recess kits are also available. Please contact your dealer.

Left and Right Front Channels

For left and right front channels, place one satellite to the left

and another to the right of the television, as shown in Figure 1.

Since the speakers are magnetically shielded, you can place

them very close to the TV without worrying about the magnetic

field distorting the picture.

Surround Channels

For left and right surround channels, place one speaker on the

left and another on the right, to the side of or slightly behind the

listening area.The surround speakers should be mounted at a

height of between 4 feet and 7 feet.

In 6- or 7-channel configurations, place the rear channel(s)

behind the listening position, as shown in Figure 2.

INFP1595Sat4000-OM 10/18/04 2:41 PM Page 4

TSS-SAT4000

INSTALLATION

Please read through this owner’s guide completely before

attempting to install or connect the speakers.We understand that

you may be anxious to play your new system, so we have made

every effort to simplify the installation and connections of the

TSS-SAT4000.

Before proceeding, you should decide how you would like to install

theTSS-SAT4000.TheTSS-SAT4000 may be mounted on the

included shelf stands; mounted on the wall using the included wall

brackets; recessed in the wall using an optional flush-mount kit; or

mounted to our optional floor stands.

Tabletop/Shelf Placement Assembly

Step One

Choose one of the three shelf stands on which to mount the

satellite. If you decide to place the stand next to a television,

the television’s height should be taken into consideration.

If you choose the shortest stand, follow steps two to four

on page 6. If you choose either of the taller stands, follow

steps two to five on page 7.

Small Medium

23-3/8"

7/8"

Large

27"

30-1/2"

INFP1595Sat4000-OM 10/18/04 2:41 PM Page 5

6TSS-SAT4000

1/4-20 x 1-1/4"

Flat-Head Screw

StepThree

For Small Table Stand Assembly

Assemble the table stand plate, the small section and the foot.

Place three nuts (provided) in base of foot and secure them

in place by three screws (provided) through the top of the

table stand plate.

Step Four

For Small Table Stand Assembly

Run speaker wire through base, and screw foot assembly to

speaker assembly.

(3) 1/4-20 Nuts

Table Stand Plate

Speaker Wire

Small Section/Collar

Foot

(3) 1/4-20 x 7/8"

Flat-Head Screws

StepTwo

For Small Table Stand Assembly

Using the included Allen wrench, remove the bottom end cap

of the speaker by unscrewing the single center screw on bottom.

NOTE: The bottom is the

side closest to the Infinity

logo on the front grille

and the speaker

connections on the rear.

Satellite Speaker

Infinity Logo

End Cap

1/4-20 x 3/4"

Screw

INFP1595Sat4000-OM 10/18/04 2:41 PM Page 6

TSS-SAT4000

Step Four

For Medium and LargeTable Stand Assembly

Use screw and washer to attach medium

or large base assembly to the

speaker assembly, as shown.

(3) 1/4-20 x 7/8"

Flat-Head Screws

(3) 1/4-20 x 7/8"

Flat-Head Screws

1/4-20 x 1"

Pan-Head Screw

Flat Washer

Flat Washers

1/4-20 x 1"

Pan-Head Screw

1/4-20 x 3/4"

Pan-Head Screw

Step Five

For Medium and LargeTable Stand Assembly

Run speaker wire through table stand plate. Use three screws

(provided) to attach plate to bottom of base assembly.

StepTwo

For Medium and LargeTable Stand Assembly

Using the included Allen wrench, remove the bottom end cap

of the speaker by unscrewing the single center screw on bottom.

NOTE: The bottom is the

side closest to the Infinity

logo on the front grille

and the speaker

connections on the rear.

Satellite Speaker

Infinity Logo

End Cap

1/4-20 x 3/4"

Screw

StepThree

For Medium and LargeTable Stand Assembly

Run speaker wire through collar. Using three screws, attach table

stand plate to the medium or large section as shown.

Speaker Wire

INFP1595Sat4000-OM 10/18/04 2:42 PM Page 7

8TSS-SAT4000

Wall-Mounting the SAT-4000 Using the Included

Wall Bracket

The customer is responsible for proper selection and use of

mounting hardware, and for correctly and safely wall-mounting

the speakers.

Step One

Remove the wall-bracket

cover by removing the four

wall bracket screws on

the ends as shown.

StepTwo

Run the speaker wire behind the

wall bracket and out the hole at

the bottom.After deciding where

to place the satellite speaker,

attach the wall bracket (in a

vertical position) to the wall

using the appropriate screws

and anchors.

StepThree

Run the speaker wires out

through the bottom hole of the

wall bracket cover. Resecure

in place as shown with four

of the wall bracket screws.

Step Five

Connect the wires (page 9).

Replace the end caps while

capturing the wall bracket in

between parts A and B and

securing it in place.Tighten

until snug.

Mounting

Screws and

Anchors

Not Included

Wall-Mount

End Cap A

Wall Bracket

Bottom Hole

Wall-Mount

End Cap B

Step Four

Using the included Allen wrench, remove the bottom end cap

of the speaker by unscrewing the single center screw on bottom.

NOTE: The bottom is the

side closest to the Infinity

logo on the front grille

and the speaker

connections on the rear.

Satellite Speaker

Infinity Logo

End Cap

1/4-20 x 3/4"

Screw

End Cap

INFP1595Sat4000-OM 10/18/04 2:42 PM Page 8

TSS-SAT4000

Step Six

The wall-bracket design allows for rotation of the speakers

at angles up to 30 degrees of center. Position the speakers

so they face toward the primary listening position, before

fully tightening.

Figure 3.This example shows how to connect bare wires to the

terminals. Banana plugs may also be inserted directly into the

rear of the connector.

1Loosen the terminals.

2Insert bare ends; tighten terminals.

CARE OF YOUR SPEAKER SYSTEM

When needed, use a soft cloth to remove any fingerprints or

to wipe off dust. Do not use any cleaning products or polished.

Clean the grille by gentle vacuuming.

– +

WIRING THE SPEAKER

After placing the speaker, you are ready to connect it to your

system. First, turn off all audio-system power. Use high-quality

speaker wire to make the connections. Consult the owner’s

manuals,included with your amplifier or receiver, for connection

and operation procedures.

Surround Modes

When using theTSS-SAT4000 in a Dolby* Digital or DTS®home

theater system, make sure the receiver’s/processor’s speaker

modes are set to“Small.”

Wiring and Polarity

The TSS-SAT4000 speaker has gold-plated terminals that

can accept bare wire.To ensure proper polarity, connect each

+ terminal on the back of the amplifier or receiver to the

respective + (red) terminal on each speaker, as shown in

Figure 3. Connect the – (black) terminals in a similar way.

See the owner’s manuals that were included with your amplifier

or receiver to confirm connection procedures.

Important!

Do not reverse polarities (i.e., + to – or – to +) when making

connections. Doing so will degrade the imaging and bass

response of the home theater system.

After correctly placing and wiring theTSS-SAT4000 and

the rest of your speaker system, adjust the levels for all of

the channels as recommended by the manufacturer of your

receiver/processor.

INFP1595Sat4000-OM 10/18/04 2:42 PM Page 9

10 TSS-SAT4000

SPECIFICATIONS

TSS-SAT4000

Frequency Response 120Hz – 20kHz (±3dB)

Nominal Impedance 8 ohms

Sensitivity 89dB

(2.83V @ 1m)

Recommended Amplifier 10 – 150 watts

Power Range

Crossover Frequencies 1,000Hz, 3,800Hz; 24dB/octave

Low-Frequency Drivers (4) 3-1/2" (89mm) MMD,

magnetically shielded

Mid-Frequency Drivers (2) 3-1/2" (89mm) MMD,

magnetically shielded

High-Frequency Driver 3/4" (19mm) MMD,

magnetically shielded

Dimensions (H x W x D) 23" x 4-1/8" x 4-3/8"

(584mm x 105mm x 111mm)

Weight 12.7 lb (5.8kg)

Infinity continually strives to update and improve existing products, as well as create new ones.

The specifications and construction details in this and related Infinity publications are therefore

subject to change without notice.

OPTIONAL ACCESSORIES

FMK-4000 Flush-Mount Kit forTSS-SAT4000

STAND-4000 Floor Stand for TSS-SAT4000

Declaration of Conformity

We, Harman Consumer International

2, route de Tours

72500 Chateau-du-Loir

France

declare in own responsibility that the products

described in this owner’s manual are in compliance

with technical standards:

EN 61000-6-3:2001

EN 61000-6-1:2001

Robin Marshall

Harman Consumer International

Chateau-du-Loir, France 10/04

INFP1595Sat4000-OM 10/18/04 2:42 PM Page 10

Inhaltsverzeichnis

Andere Infinity Sprecher Handbücher

Infinity

Infinity PS-12 Bedienungsanleitung

Infinity

Infinity SAT-750 Bedienungsanleitung

Infinity

Infinity PRIMUS Primus P152 Bedienungsanleitung

Infinity

Infinity Total Solutions TSS-1200 Bedienungsanleitung

Infinity

Infinity 10.3t Bedienungsanleitung

Infinity

Infinity Kappa Series 32.9cf Bedienungsanleitung

Infinity

Infinity TSS 3-IN-1 Bedienungsanleitung

Infinity

Infinity CS 60R Bedienungsanleitung

Infinity

Infinity Intermezzo 3.5c Bedienungsanleitung

Infinity

Infinity Primus P143 Bedienungsanleitung

Infinity

Infinity Kappa 10.5t Bedienungsanleitung

Infinity

Infinity ERS 110DT Bedienungsanleitung

Infinity

Infinity L-MPS Bedienungsanleitung

Infinity

Infinity Beta CSW-10 Bedienungsanleitung

Infinity

Infinity SM-165 Bedienungsanleitung

Infinity

Infinity Total Solutions TSS-CENTER4000 Bedienungsanleitung

Infinity

Infinity C205 Infinity Classia Bedienungsanleitung

Infinity

Infinity Omega Bedienungsanleitung

Infinity

Infinity C205 Bedienungsanleitung

Infinity

Infinity Minuette L-MPS Bedienungsanleitung

Infinity

Infinity Alpha Series Bedienungsanleitung

Infinity

Infinity Minuette MPS Satellite Bedienungsanleitung

Infinity

Infinity ERS 610 Betriebsanleitung

Infinity

Infinity Total Solutions TSS-SUB4000 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung