InFocus SP5000 Bedienungsanleitung

1 COMMAND LINE INTERFACE

1.1.1 Purpose

This specification defines the serial command line streams for controlling an InFocus projector through

the RS232 connector to the projector. These commands are intended to provide a simple set of controls

to the projector through what InFocus calls the Command Line Interface (CLI). The CLI is designed for

use by what the industry commonly calls boardroom controllers. The CLI will accept commands via

RS232 to control the necessary features used by most boardroom controllers. This CLI language uses

a simple human readable protocol to help facilitate the installers’ time necessary to setup or diagnose a

problem with boardroom control installations. However, the CLI is not a guaranteed delivery system.

1.1.2 Message Format

As commonly used in math notation, everything is evaluated in the parenthesis first, as the parentheses

are designed to group things together. This same parenthesis nomenclature is used to group a

command and its data together (nested parenthesis are not supported). All commands are three alpha

characters followed by the request. The request can be a “?” symbol that signifies a read request, or a

numerical number represented by 1 to 4 ASCII digits, that signifies a write request. Not all commands

support reading and writing. The command table indicates the commands and requests that are

supported. There are also support commands available on non CLI format.

1.1.3 Write Commands

Write commands have the following format:

(AAA####) where,

( -startstheCLI command

AAA -denotes theCLI function

#### -denotesthevalueto bewritten (leadingzeros arenot necessary)

) -endstheCLIcommand

Some functions have ranges for settings while others are Boolean. Settings with ranges range from

zero to a maximum number. If a number greater than the maximum is received, it is automatically

limited to the maximum number for that function. IT IS SUGGESTED THAT EACH FUNCTION BE

QUERIED FOR ITS RANGE WITH A READ COMMAND BEFORE ISSUING A WRITE COMMAND.

Boolean settings consider 0 as off and 1-9999 as on. The only exception is the Power command. The

only valid write values that will be accepted will be ‘0’ for turning the power off and ‘1’ for turning the

power on.

Examples:

Brightness Command (BRT10) Sets the brightness to 10

Volume Command (VOL0000) Set the volume to 0

Freeze Command (FRZ1) Freeze the display

Freeze Command (FRZ9999) Freeze the display

Power Command (PWR0) Turn power off

Power Command (PWR1) Turn power on

Power Command (PWR9999) Command not recognized

1.1.4 Increment Commands

Increment commands have the following format:

(AAA+####) where,

( -startstheCLI command

AAA -denotes theCLI function

+ -denotesIncrementcommand

#### -Isoptionalanddenotesnumberofstepsto beincremented(leading zerosarenot

necessary)

) -endstheCLIcommand

Examples:

Brightness Command (BRT+10) Increment brightness 10 steps

Brightness Command (BRT+) Increment brightness 1 step

1.1.5 Decrement Commands

Increment commands have the following format:

(AAA-####) where,

( -startstheCLI command

AAA -denotes theCLI function

- - denotesdecrement command

#### -Isoptionalanddenotesnumberofstepsto bedecrement (leadingzeros arenot

necessary)

) -endstheCLIcommand

Examples:

Brightness Command (BRT-10) Decrement brightness 10 steps

Brightness Command (BRT-) Decrement brightness 1 step

1.1.6 Read Commands

Read commands have the following format:

(AAA?) where,

( - starts the CLI command

AAA - denotes the CLI function

? - denotes the read request

) - ends the CLI command

A read command returns the current setting in an ASCII format enclosed in parentheses.

The following Format is defined:

1) Range Format (r-R,V)

2) String Format (S)

1.1.6.1 Range Format: (r-R,V)

where

( open parenthesis marks the start of the CLI response

r minimum value of the setting’s range

R maximum value of the setting’s range

V the current value of the setting

) closing parenthesis marks the end of the CLI response

Examples:

(VOL?) Read the current range and value of the projector’s volume

Returns: (0-127,64)

(BRT?) Read the current range and value of the projector’s brightness

Returns: (0-255,128)

1.1.6.2 String Format: (S)

where

( open parenthesis marks the start of the CLI response

S character string

) closing parenthesis marks the end of the CLI response

Examples:

(VER?) Read the current software version

Returns: (v2.0)

1.1.7 Error Handling

When the closing parenthesis is received, the command is validated before it is processed. If the

received command is determined to be invalid, a question mark character will be returned as a error

response.

Examples:

(123?) “123” is not a valid CLI command prefix. This read request will return ‘?’

(VOL ?) “VOL” is a valid CLI command prefix, but the spaces between the prefix and the

question mark character invalidates the command. This read request will

return ‘?’.

Not all settings are readable. If an attempt is made to read from a write-only setting, the projector will

return a question mark.

Example:

(RST?) If the RST CLI command is write only, this read request will return ‘?’.

A more descriptive error message on the errors can then be queried with the (ERR?)

command. The following message are defined:

(No Error Detected)

(Unknown command)

(Unknown parameter)

(Command not supported by this projector)

(Command only available in Power on)

(Projector not ready to be turned on)

(Command only available with valid input source)

(Command only available with external module)

(Command failed)

(Write only Command)

(Command only available in RGB)

(Command only available in VIDEO)

(Command only available in NTSC)

1.1.8 Limitations

The CLI cannot respond to commands coming in at a high rate. Therefore, a delay must occur

between commands to ensure that the command is properly executed before the next one is received.

The recommended approach for interfacing to the projector is:

Read:

1. Send the read command

2. Receive read response

Write

1. Send the write command

2. Verify that an error response ‘?’ was not received.

Continually query (for a predefined time) the setting until the value has changed

Some settings don’t implement the full range of values in the setting’s defined range. If an attempt is made to change

the setting to an unsupported value, the CLI will round down to the nearest supported value.

1.1.9 Help Commands

There are help commands available on non CLI format. The following non CLI commands is available in plain text:

help - Prints help screen

cli AAA - Prints help information for the AAA command

cli cmds - Prints an alphabetical list of CLI commands

cli all - Prints the current value of all CLI settings

cli verbose on/off - Turns verbose on and off

1.1.10 Serial Communications Configuration

The following table describes the serial communication configuration that should be used when interfacing to the CLI via

the serial port. Windows HyperTerminal or Procomm are two tools that can be used to send CLI commands across the

serial port.

Setting Value

Bits per second 19200

Data bits 8

Parity None

Stop bits 1

Flow Control None

Table 1 Configuration

2 TABLE OF COMMANDS

All commands in the table may not be available for your current product. Run the help command CLI ALL to get a list of

supported commands.

Abbreviations:

NA = Not Available, Src.dep = Source depended use a read request with ? to get current supported range.

Function Command Attribute Range Default

Power PWR R & W 0 – 1

0 – Off

1 – On

Rear REA R & W 0 – 1

0 – Off

1 – On

Ceiling CEL R & W 0 – 1

0 – Off

1 – On

Auto Ceiling ACL R & W 0 – 1

0 – Off

1 – On

Display Message DMG R & W 0 – 1

0 – Off

1 – On

Power Save PSV R & W 0 – 1

0 – Off

1 – On

Auto Power Enable APO R & W 0 – 1

0 – Off

1 – On

Low Power Enable LPE R & W 0 – 1

0 – Off

1 – On

Screen Saver SSV R & W 1 – 6

1 – 5 min

2 – 10 min

3 – 15 min

4 – 20 min

5 – 25 min

6 – 30 min

Blank Screen BLK R & W 0 – 1

0 – Off

1 – On

Display Startup Logo DSU R & W 0 – 2

0 – Default

1 – Blank Screen

2 – Capture

Blank Screen Color BSC R & W 1– 2

1 – blue

2 – white

Effect Key EFK R & W 0 – 10

0 – Blank

1 – Mute

2 – Mask

3 – Aspect Ratio

4 – Source

5 – Auto Image

6 – Freeze

7 – Zoom

8 – About

9 – PiP

10 – Screen Trigger

Language LAN R & W 0 – 11

0 – English

1 – French

2 – German

3 – Spanish

4 – Chinese Traditional

5 – Japanese

6 – Korean

7 – Portuguese

8 – Russian

9 – Norwegian

10 – Chinese Simplified

11 – Italian

Menu Enable MNU R&W 0 – 1

0 – Off

1 – On

Menu Navigation NAV R&W 0 – 4

0 – up

1 – down

4 – select

Error Message ERR R ? NA

Screen Trigger SCT R&W 0 – 1

0 – Off

1 – On

BackLight LBL R&W 0 – 1

0 – Off

1 – On

Sleep Timer SLT R&W 0 – 1

0 – Off

1 – On

Table 2 System Commands

Function Command Attribute Range Default

Horizontal Keystone

Correction DKH R & W 0-100 50

Vertical Keystone

Correction DKV R & W 0-100 50

Auto Vertical Keystone AVK R&W 0 – 1

0 – Off

1 – On

Contrast CON R & W 0-100 50

Brightness BRT R & W 0-100 50

Color CLR R & W 0-100 50

Tint TNT R & W 0-100 50

Aspect ratio ARZ R & W 0–5

0 – native

1 – 16:9

2 – 4:3

3 – Letterbox

4 – 16:9 text

5 – Natural Wide

6 – 2.35:1

Presets PST R & W 0 – User1

1 – User 2

2 – User 3

3 – None

Gamma

Freeze Display FRZ R&W 0 – 1

0 – Off

1 – On

Overscan OVS R&W 0 – 1

0 – Off

1 – On

Gamma Table GTB R & W 0 – Presentation

1 – Photography

2– Film

Table 3 Picture

Function Command Attribute Range Default

Sharpness SHP R & W 0–4

0– Softest

1 – Soft

2– Standard

3 – sharp

4 – sharpest

Color Temp User Blue BCG R & W 0-100 50

Color Temp User Green GCG R & W 0-100 50

Color Temp User Red RCG R & W 0-100 50

Color Temp TMP R & W 1–3

1– Low

2 – Medium

3 – High

Auto Image AIM W 1 1

Phase MSS R & W 0-100 NA

Tracking MTS R & W

Src.dep NA

H Position HPS R & W Src.dep NA

V Position VPS R & W Src.dep NA

Mask MSK R&W 0-1000 0

Color Space Mapping CSM R&W 0–4

0– RGB

1 – SMTPE240

2– REC709

3 – REC601

4 – AUTO

Red Gain RCG R & W 0-100 50

Green Gain GCG R & W 0-100 50

Blue Gain BCG R & W 0-100 50

Red Offset RCO R & W 0-100 50

Green Offset GCO R & W 0-100 50

Blue Offset BCO R & W 0-100 50

Gamma Red GAR R & W 0-100 50

Gamma Green GAG R & W 0-100 50

Gamma Blue GAB R & W 0-100 50

Table 4 Picture Advance

Function Comm

and Attribute Range Default

Source 1 SR1 R & W 0 – 5

0 – Source1

1 – Source2

2– Source3

3 – Source4

4 – Source5

5 – Source6

Source 2 SR2 R & W 0 – 5

0 – Source1

1 – Source2

2– Source3

3 – Source4

4 – Source5

5 – Source6

Source 3 SR3 R & W 0 – 5

0 – Source1

1 – Source2

2– Source3

3 – Source4

4 – Source5

5 – Source6

Source 4 SR4 R & W 0 – 5

0 – Source1

1 – Source2

2– Source3

3 – Source4

4 – Source5

5 – Source6

Power Up Source DSC R & W 0 – 6

0 – Source1

1 – Source2

2– Source3

3 – Source4

4 – Source5

5 – Source6

6- LastUsed

Auto source ASC 0 – 1

0 – Off

1 – On

Computer source advance CAD W 1

1 – Perform advance NA

Video source advance VAD W 1

1 – Perform advance NA

Source SRC R & W 0 – 5

0 – Source1

1 – Source2

2– Source3

3 – Source4

4 – Source5

5 – Source6

Image Locked and Displayable ILK R 0 – 1

0– Not Locked

1 – Locked and

displayed

Save User 1 Settings US1 W 1

1 – Save User 1 Setting NA

Save User 2 Settings US2 W 1

1 – Save User 2 Setting NA

Save User 3 Settings US3 W 1

1 – Save User 14Setting NA

RGB Video RVI R&W 0 – 1

0 – Off

1 – On

Table 5 Sources

Function Command Attribute Range Default

Factory Reset RST W 1

1 – Perform Factory Reset NA

Perform lamp hours

reset LRT W 1

1 – Lamp hours Reset NA

Time lamp 1 lasted

(hours) LB1 R 0-100000

Time lamp 2 lasted

(hours) LB2 R 0-10000 NA

Time lamp 3 lasted

(hours) LB3 R 0-10000 NA

Time lamp 4 lasted

(hours) LB4 R 0-10000 NA

Time lamp 5 lasted

(hours) LB5 R 0-10000 NA

Lamp Lit LML R 0-1

0 – Lamp not Lit

1 – Lamp Lit

Lamp Time (hours) LMP R 0-10000 NA

Lamp total time on for

all bulbs (hours) LMT R 0-1000000 NA

Table 6 Service

Function Command Attribute Range Default

Balance BAL R&W 0-100 50

Volume VOL R&W 0-100 50

Mute MTE R&W 0 – 1

0 – Off

1 – On

Loudness LOD R&W 0 – 1

0 – Off

1 – On

Shime ACE R&W 0 – 1

0 – Off

1 – On

Table 7 Audio

Andere Handbücher für SP5000

Inhaltsverzeichnis

Andere InFocus Projektor Handbücher

InFocus

InFocus IN5542 Bedienungsanleitung

InFocus

InFocus CEILING MOUNT LP 1000 SERIES Kurzanleitung

InFocus

InFocus IN2124a Bedienungsanleitung

InFocus

InFocus SP4800 Handbuch

InFocus

InFocus LitePro 610 Installationsanleitung

InFocus

InFocus Work Big IN32 Bedienungsanleitung

InFocus

InFocus SP7205 Bedienungsanleitung

InFocus

InFocus LitePro Bedienungsanleitung

InFocus

InFocus IN5534 Bedienungsanleitung

InFocus

InFocus IN5122 Bedienungsanleitung

InFocus

InFocus IN102 Bedienungsanleitung

InFocus

InFocus IN1156 Bedienungsanleitung

InFocus

InFocus IN2124a Bedienungsanleitung

InFocus

InFocus IN5502 Bedienungsanleitung

InFocus

InFocus LP 740TM Referenzhandbuch

InFocus

InFocus LP755 Bedienungsanleitung

InFocus

InFocus LP740B Bedienungsanleitung

InFocus

InFocus IN124STA Bedienungsanleitung

InFocus

InFocus IN1110 Bedienungsanleitung

InFocus

InFocus Proxima DP6850 Bedienungsanleitung

InFocus

InFocus LP290 Bedienungsanleitung

InFocus

InFocus Work Big IN2102 Bedienungsanleitung

InFocus

InFocus LP 815 Kurzanleitung zur Einrichtung

InFocus

InFocus IN5302 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung