Ingenico group AXIUM DX8000 Bedienungsanleitung

WWW.ingenico.com

28-32,Boulevard de Grenelle, 75015 PARIS - FRANCE/ (T)+33(0)1 58 01 80 00 / (F)+33 (0)1 58 01 91 35

Ingenico-SA au capital de 47 656 332 / 317 218 758 RCS Nanterre

User Guide

Model：AXIUM DX8000

1. Introduction

We hope that you will be fully satisfied with your new AXIUM DX8000 terminal.

Read this guide to understand and make the best use of your terminal. It presents you

the necessary information about use, installation, maintenance, safety and security

recommendations.

WARRANTY/SECURITY/GARANTIE/SÉCURITÉ

Use only the power supply included with the product to ensure best performance and

safety. Maintenance should only be provided by ingenico authorized technician.

Failure to comply with these instructions will void the manufacturer’s responsibility.

Afin d’assurer les meilleures performances et votre sécurité, utiliser seulement le bloc

d’alimentation livré par le fabricant avec le produit. La maintenance doit être réalisée seulement

par un technicien agréé et autorisé par Ingenico.

Le non-respect de ces instructions dégage la responsabilité du fabricant.

This symbol indicates there are warnings or cautions need to be

checked in the user guide. symbol indicates an important

Warning.

Ce symbole indique que des avertissements ou des mises en garde

doivent être vérifiés dans le manuel de l'utilisateur.

This symbol indicates an important Warning.

Ce symbole indique un avertissement important.

This symbol indicates a piece of advice.

2. Presentation

2.1 Content of the box

AXIUM DX8000 terminal unit equipped with a paper roll

Power adapter

A battery pack

This user guide

WARNING/ATTENTION

The power supply unit provided with your equipment is specially designed for

ingenicoAXIUM DX8000 terminal. Do not use any other power supply. The use of a power

supply with apparently similar voltage/current characteristics may damage your terminal.

Le bloc d’alimentation fournit avec votre équipement est spécialement conçu pour les terminaux

de paiment Ingenico. Ne pas utiliser d’autres sources d’alimentation. L’utilisation d’une

alimentation électrique ayant des tensions et courant similaires peut endommager votre

équipement.

ADVICE

Keep the package. It must be re-used whenever the terminal is shipped.

2.2Overview of AXIUM DX8000

1. Contactless landing zone

2. LCD and touch screen

3. Smart card reader

4. Buzzer

5. Magnetic card reader

6. Easy Loading Printer

7. Power Key

8. Volume Keys

9. Battery cover

10. USB Type-C connector

11.Front scanner

12. LEDs for Contactless Card

2.3Keypad Functions

The terminal has three physical keys on the left side of the terminal, a power button and

two volume keys.

If the terminal has a 5.99 inchscreen, there are three virtual keys at the bottom of the

screen,Menu,Homeand Back keys.

If the terminal has a 5.5 inchscreen, there are three capacitive keys at the bottom of the

screen,Menu,Homeand Back keys.

2.4Touch Panel

The AXIUM DX8000 is equipped with touch panel that allows you capture functions and

menus by your finger or use a stylus.

3. Use of the terminal

ADVICE

Before using the terminal, always check if the roll of paper is present

3.1 Power on/Power off the terminal

To power on: Make sure the terminal battery is correctly installed and Press <Power>

button for about 1s until the display is turned up.

To power off: Press <Power> button for more than 2s until the display show the following

figure, then press <Power off>.

If the battery is empty, the terminal automatically shuts off.

Abnormal power off:

When the device works abnormally, for example, it is crashed and no actions menu

popped out while pressing the power button, pleaselong-press the power button for 8s,

the device will be automatically powered off.

Screen saver mode:

Short-press the power button for about 0.5s, the terminal display will be turned on or off.

3.2Reading cards

Magnetic stripe card

The card can be read bi-directionally, with the stripe facing the terminal.

Use a regular movement in order to ensure a reliable card reading.

Contactless card

Bring the card firmly up to the active zone. Keep the card close to

the reader during the transaction.

On the front, LEDs are displayed to indicate transaction processing.

Smart card

Insert the card horizontally with the metal chip facing upward

and leave in position throughout the transaction.

3.3Usage of Front Camera

The brightness of the mobile phone must be set to the brightest or not less than the

2/3 of the maximum brightness.

The screen of the mobile phone must

face the front scanning head above the

terminal screen and keep itstationary.

The screen of the mobile phone must be

parallel to the front scanning head.

The vertical distance between the screen

of the mobile phone and the front

scanning head should be between 10~ 30

cm; 20 cm would be the best.

The terminal will beep with a successful

scanning.

3.4USB type-C

There is a USB type-C connector on the left side

of the terminal.

The connector manages Host and Slave

connections.

The connector integrates Audio Jack solution.

WARNING/ATTENTION

To prevent possible hearing damage, do not listen at high volume levels for long

periods.

Afin d’éviter d’éventuels dommages auditifs, ne pas écouter à des volumes

élevées pendant de longues périodes.

4. Installation

4.1 Recommendations

Operating conditions

(*)Excluding battery charging

Battery charging conditions

Storage conditions

4.2Installing modules

4.2.1 SAM1/SAM2

WARNING/ATTENTION

Switch off the terminal before opening the trapdoor.

Mettre hors tension le terminal avant d’ouvrir la trappe.

The SAM connectors are located inside the terminal, in a closed compartment.

Turn the terminal and remove the trapdoor.

SAM1, SAM2 are identified by the engraved marks on the lower housing.

When introducing a SAM in its slot, be sure to put the cut corner as indicated on the

picture.

Ambient temperature*

From -10℃to +50℃

Max relative humidity

From 10%to 90%, Non-condensing

Ambient temperature

From 0℃to +40℃

Ambient temperature

From -20℃to +70℃

Max relative humidity

From 5% to 90%, Non-condensing

Close the trapdoor.

ADVICE

AXIUM DX8000 is equipped with a dual SAM slot.

When using two SAM cards, it is recommended to insert the bottom one first, then the

top one.

When using only one SAM card, it is recommended to insert SAM1 slot (bottom).

4.2.2 MicroSD Memory Card

WARNING/ATTENTION

Switch off the terminal before opening the trapdoor.

Mettre hors tension le terminal avant d’ouvrir la trappe.

MicroSD connector is located inside the terminal, in a closed

compartment.

Turn the terminal and remove the trapdoor.

MicroSD are identified by the engraved marks on the lower

housing.

Insert MicroSD card and push it to the end.

Close the trapdoor.

The terminal supports MicroSD up to 32GB.

Inhaltsverzeichnis

Andere Ingenico group Touch-Terminal Handbücher

Ingenico group

Ingenico group Move 3500 MIX Bedienungsanleitung

Ingenico group

Ingenico group Move/3500 Bedienungsanleitung

Ingenico group

Ingenico group Desk 3500 Bedienungsanleitung

Ingenico group

Ingenico group swipen Move 5000 Bedienungsanleitung

Ingenico group

Ingenico group Move 3500 WiFi Bedienungsanleitung

Ingenico group

Ingenico group Move 3500 3G Bedienungsanleitung

Ingenico group

Ingenico group iPP300 Series Bedienungsanleitung

Ingenico group

Ingenico group AXIUM DX8000-BASE-W2 Bedienungsanleitung

Ingenico group

Ingenico group EX8000 Bedienungsanleitung

Ingenico group

Ingenico group iSMP v4 Wi-Fi Bedienungsanleitung

Ingenico group

Ingenico group Link/2500 Bedienungsanleitung

Ingenico group

Ingenico group Desk 3500 Bedienungsanleitung

Ingenico group

Ingenico group AXIUM DX4000 Bedienungsanleitung

Ingenico group

Ingenico group Move 3500 BLUETOOTH Bedienungsanleitung

Ingenico group

Ingenico group Desk Series Bedienungsanleitung

Ingenico group

Ingenico group Yorkshire Payments ICT200 Bedienungsanleitung

Ingenico group

Ingenico group swipen Desk 5000 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung