Ingics IGS03W Bedienungsanleitung

INGICS TECHNOLOGY



iGS03W/M is a gateway to bridge the local BLE( Bluetooth® Low Energy) tags,

sensors, or beacons to remote server/cloud by WiFi, or LTE-M. Through an easy web

UI interface, user can configure the Internet access to upload reports to cloud server

by TCP, HTTP(S), or MQTT(S). This guide is to help the user to figure out how to

operate and configure the iGS03.



Contents:

Overview

Block Diagram

SIM

WiFi

BLE

GNSS

Example case 1: The device is in fixed position:

Example case 2: The device is moving:

Payload Format

BLE

GPS

Button

Reset to Default

WPS

LEDs

Configuration

Web User Interface

System

Wi-Fi

AP Mode

Station Mode

Network

WiFi Address

DHCP Server (WiFi AP)

Applications

TCP Server

TCP Client

HTTP Client

HTTPS

MQTT Client





Guide

Ver.01a

Beacon Gateway

iGS03W/M User Manual

 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

1

INGICS TECHNOLOGY
MQTTS
Common Settings
Content Type
Keep Alive
Append Timestamp
Request Interval
Cache full handling
Throttle Control
Cloud IoT Helper
Advanced
BLE Configuration
BLE-5 PHY Mode
Active Scan Mode
BLE Filter
RSSI Threshold
Payload Whitelist
BLE MAC Whitelist
Security
Device Key/Certification/Server CA Upload
LTE
LET Settings
APN
Auth
Username/Password
GNSS Settings
NTP Setting
Certification
Bluetooth SIG Qualification
Japan MIC Reaulatory
FCC Regulatory
FCC Statements
CE Regulatory
Revision History


 


          INGICS TECHNOLOGY CO., LTD.    •    [email protected]    •    WWW.INGICS.COM
  2

INGICS TECHNOLOGY

Overview

The iGS03 BLE gateway scans beacons(like iBeacon or Eddystone), proprietary tags, or BLE

sensors then sends the payload to TCP, HTTP or MQTT server. Users can configure the transmit period

and server endpoint through a simple web UI. There are two models, iGS03W and iGS03M, representing

different uploading interfaces, WiFi and LTE-M.



Block Diagram

 



 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

3

INGICS TECHNOLOGY

SIM

To use iGS03M (LTE-M Model), you have to put a Cat-M1 micro

SIM card into the socket of iGS03M. Please open the bottom cover to

insert the SIM card. The steps to open the bottom cover are as below,



WiFi

The 2.4G WiFi AP connection is used to configure the unit through web UI. iGS03 works as an

WiFi Access Point(AP) supporting DHCP. Users must connect to this AP to configure the unit.

BLE

The BLE subsystem operates in listening mode. It collects the messages advertised by BLE

devices. These messages are then sent to the cloud server configured by the user.

iGS03 supports two BLE modes

1. LE 1M PHY: including BLE4.2(Legacy)/BLE5, 1M in 100% duty cycle

2. LE Coded PHY: BLE5, 125K( long range) in 100% duty cycle



Step 1. Remove external BLE antenna

Step 2. Remove the screw from bottom cover



Step 3. Use finger to press and hold the arrow

part

Step 4. Pull out the bottom cover



 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

4

INGICS TECHNOLOGY

The default PHYMODE is 1, LE 1M PHY mode.

Users can use webUI or telnet command to configure the mode.

GNSS

The GNSS function is turned “off” by default. Users can use webUI to enable or disable GNSS.

For detail settings, use below telnet commands to manage the GNSS behavior:



GNSS ENABLE Enable/Disable GNSS, default off

GNSS FIXCOUNT Number of attempts for positioning, 0 indicates continuous positioning.

default 0

GNSS FIXRATE The interval time between the first and second time positioning, default 1 (1

second)

GNSS RPTRATE The interval time for sending GPSR report, default 600 (10 minutes)

GNSS INFO To get latest GPS status

Example case 1: The device is in fixed position:

e.g.

GNSS ENABLE 1

GNSS FIXCOUNT 5

GNSS FIXRATE 60

GNSS RPTRATE 60

Then GNSS will be enabled and get positioned for 5 times with a 60 seconds interval.

GNSS will be off automatically after getting position for 5 times.

Example case 2: The device is moving:

e.g.

GNSS ENABLE 1

GNSS FIXCOUNT 0

GNSS FIXRATE 1

GNSS RPTRATE 60

Then GNSS will be enabled and continuously get position with 1 second interval, and it will send

a GPSR report every 60 sec.



You can also use the "GNSS INFO" command to get the latest coordinates.



 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

5

INGICS TECHNOLOGY

Payload Format

There are several kinds of payload format that iGS03 will send to the server.

BLE

General format:



$<report type>,<tag id>,<gateway id>,<rssi>,<raw packet content>,*<unix epoch timestamp>\r\n



Report Type:

$GPRP BLE4.2 General Purpose Report

$RSPR BLE4.2 Scan Response Report

$LRAD BLE5 Long Range ADV

$LRSR BLE5 Long Range Scan Response

$1MAD BLE5 1M ADV

$1MSR BLE5 1M Scan Response



Examples:

$GPRP,CCB97E7361A4,CB412F0C8EDC,-49,1309696773206D65736820233220285445535429020106,1574921085

$GPRP,E5A706E3923A,CB412F0C8EDC,-87,0201041AFF590002150112233445566778899AABBCCDDEEFF0000100C3BB,157

4921085

$LRAD,51A88AD374B7,CC4B73906F96,-87,02010212FF0D0083BC280100AAAAFFFF000010030000,1574921085

$GPRP,0C61CFC1452E,E7DAE08E6FC3,-44,0201061AFF4C000215B9A5D27D56CC4E3AAB511F2153BCB9670001452ED6

(iBeacon, UUID: B9A5D27D56CC4E3AAB511F2153BCB967, Major: 0001, Minor: 452E)

GNSS

General format:



$GPSR,<tag_mac>,<reader_mac>,<rssi>,yymmdd,hhmmss.ss,latitude,longitude,speed,hdop(,timestamp)

●"$GPSR,<tag_mac>,<reader_mac>,<rssi>" fields are for compatibility with other reports. The

tag_mac is always the same as reader_mac and the rssi is always -127.

●yymmdd,hhmmss.ss is the UTC time when the position is acquired.



<report type>

Different report type to distinguish the source of the report.

<tag id>

MAC address or ID of tag/beacon

<gateway id>

MAC address of gateway

<rssi>

RSSI of tag/beacon

<raw packet content>

Raw packet received by the gateway

<unix epoch timestamp>

Optional timestamp configured in applications page

 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

6

INGICS TECHNOLOGY

●speed: The unit is knots.

●hdop: Horizontal dilution of position



Example:

$GPSR,CC4B73906F96,CC4B73906F96,-127,191127,233821.00,24.993631,121.423264,0.0,2.4,1574897900

Button

One button is located on the back panel. It is used for WPS function or Reset to default settings.



Reset to Default

Pressing the reset button on your device for over 3 secs to retrieve the default setting. While the

network status LED turns into red light, release the button, and the iGS03M will reboot with its default

settings.

WPS

Users can use the WPS button to join iGS03M to the WiFi Access Point. First press the WPS

button on your Access Point, when it is ready, then press the WPS button for over 1 sec on the iGS03M

device to join the Access Point. 





Function

Trigger Condition

WPS

short press for over 1sec and release

Reset to default settings

long press for over 3 sec

 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

7

INGICS TECHNOLOGY

LEDs

There are two LEDs indicating the current status. The left one is BLE status LED and the right one

is Network status. Below are their behaviors.



Configuration



To configure the unit, you have to connect it through the WiFi interface. When it is powered on,

you could scan its native AP and connect it with the WiFi of your NB/PC/Mac/Tablet/Smartphone. It’s



On

Flash

BLE

Status

LED

find tag/beacon in range

BLE transmission

happening

Network

Status

LED

WiFi/LTE-M connection

success

(This only implies the network

is connected. It doesn’t mean

the server is connected)

Green: WiFi/LTE-M

network transmission

happening

Orange:

If IGS03M does not insert

SIM card and being used

as WiFi device

Network Status LED behavior

Description

Status

ORANGE LED on (500ms)

Boot start

Booting

RED LED blink (100ms on/off)

Joining AP (If WiFi in STA mode)

Booting

RED LED blink (500ms on/off)

LTE connecting carrier

Booting

GREEN/ORANGE LEDs blink interleaved

(100ms)

WPS enrollee

WPS

GREEN LED on

Network ready

Ready/Idle

ORANGE LED on

Network ready (If SIM card is not inserted)

Ready/Idle

GREEN LED blink (200ms on/off)

Network is transfering data

(If SIM card is not used on iGS03M, shows

ORANGE LED blink instead)

Busy

RED LED ON (1sec)

Connect failure

Error

RED LED blink (5sec on/off)

Misconfiguration

Error

RED LED ON (5sec)

LTE init failure

Error

 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

8

INGICS TECHNOLOGY

SSID is just like the above figure with part of the mac address. The default key to connect with it is

“12345678”. You can change it later when you get into the web UI.

After connection, enter IP address 192.168.10.1 in your browser. The default account/password

are both “admin”. The following sections describe details of the web UI.

Web User Interface

You can review current configuration or modify it on the web UI. There are various function

groups listed on the top of UI.



Any change in the page needs to be saved first before switching to another page, otherwise the

modification will be lost. And after all changes made, click reboot to make the changes effective.



System

Display firmware and device information, including MAC address and IP address in station mode

are shown here.

Wi-Fi

Users can configure iGS03M’s WiFi device as an WiFi AP or join to the other AP. The related

settings can be managed on this page.

AP Mode

SSID: The default name is IGS03 plus

the last digits of the mac address.

Security: Open, WPA-PSK, WPA2-PSK

and WPA-PSK/WPA2-PSK are

supported. WPA2-PSK is

recommended.

Password: 8-63 characters can be

input

Channel: 1~11(ch12 and ch13 could be supported by request)



 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

9

INGICS TECHNOLOGY

Station Mode

This mode is used for transferring

data by *WiFi.

Scan: Click it to scan available APs.

The scan result list will be displayed

on the popup window, and the user

can choose the correct AP from the

list.

SSID: No manual input required. It is automatically filled once a user chooses an AP from

the scan result list.

Security: Basically it is automatically detected and selected after choosing an AP from the

scan list. But in case the AP setting is in WEP open or WEP shared, the user has to

confirm it by himself/herself.

Password: Type the one assigned in your AP.

*Note: In data transfer, by default, WiFi has higher priority than LTE. So for iGS03M if both

interfaces are configured correctly and connected, the data will be transferred by WiFi.

Users can change the priority through the Telnet command.

Network

WiFi Address

This setting is for configuring in WiFi

Station mode. Normally the “DHCP

Client” is used to join a WiFi AP w/

DHCP. If one wants to manually assign

an IP address for iGS03, choose “Static

IP” to to assign the IP Address,

Netmask, Gateway, and/or DNS

servers.

DHCP Server (WiFi AP)

The default IP address of iGS03 in WiFi AP mode is 192.168.10.1 and the netmask is



 INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM

10

Andere Handbücher für iGS03W

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ingics Tor Handbücher

Ingics

Ingics iGS02E Bedienungsanleitung

Ingics

Ingics iGS03W Bedienungsanleitung

Ingics

Ingics iGS01S Bedienungsanleitung

Ingics

Ingics iGS01S Bedienungsanleitung

Ingics

Ingics IGS01 Bedienungsanleitung

Ingics

Ingics iGS03W Bedienungsanleitung

Ingics

Ingics iGS03W Bedienungsanleitung

Ingics

Ingics IGS01 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung