Ingram Products APT-9S Bedienungsanleitung

APT-9S

Programmable Timer

Quick Start Guide

Introduction

The APT-9S Programmable timer provides a compact time controller which may be panel or DIN-rail

mounted. The unit includes an integrated battery backed clock / calender function which retains the

programming and time-of-day information when power is lost. The APT-9S supports three operating

modes: Timer Pulse and Dual Timer.

When operated as a Timer the unit will turn ON or OFF the relay contact at specific times of the

day/week and will store up to 80 unique Timer Mode programs.

When operated in the Pulse mode the relay contact will be pulsed ON for a specific duration (pulse

width) at specific times of the day/week. The unit will store up to 160 unique Pulse Mode programs.

The Dual Timer mode allows the unit to continuously cycle ON/OFF with programmable ON and OFF

times.

Features

Flexible programming using integrated front panel controls and LCD menu screen.

Three operating modes:

TIMER (80 programmable ON/OFF times)

PULSE generator (160 programmable pulse times)

CYCLIC TIMER (repeated ON / OFF cycles of programmable duration).

Battery backed time-of-day clock

Manual Override

240 Vac/7 Amp N.O. 5 Amp/N.C. Relay contacts

Flexible 12-48 Vdc or 100 – 240 Vac power options

1 / 6 © Ingram Products Inc 02/19/12

APT-9S

Programmable Timer

Quick Start Guide

PROGRAMMING THE APT-96

When the BAT. Switch is switched ON the APT-96 will automatically enter the CLOCK SET-UP mode.

In normal operations this switch should be left in the ON position. Note that turning the BAT. Switch to

the off position will not erase the program memory – see clock SET-UP MODE below.

The CLOCK SET-UP mode is exited by pressing the MODE switch causing the unit to enter the

NORMAL OPERATING mode.

MODE SWITCH

The MODE switch cycles the unit through 5 distinct operating/programming modes:

2 / 6 © Ingram Products Inc 02/19/12

TIME SETUP

NORMAL MODE

TIMER SETUP PULSE SETUP

HOLIDAY SETUP

DUAL TIMER

TIMER/PULSE Switch

Pressing the

START button will

return to the

NORMAL mode

except in the

DUAL TIMER

mode

BAT. OFF-> ON

APT-9S

Programmable Timer

Quick Start Guide

C OCK SET-UP Mode

SWITCH FUNCTION

DAY Selects the current Day of the Week

HR (12/24H) Sets the current Hour

MIN (+H) Sets the current Minute

MODE Exits Clock SETUP mode advances to NORMAL mode

CLEAR WARNING: Holding this key for ~ 5 seconds will clear all internal memory. The

entire rogram will be lost.

NORMA OPERATING Mode

While in the Normal Operating Mode the unit will track the current time and activate the output relay

according to the previously established program schedule.

SWITCH FUNCTION

HR (12/24H) Switches between 12 and 24 HR display format

MIN (+H) Adds 1 to the Hour value (Daylight Saving Time adjustment)

SEC (MAN) Toggles relay ON/OFF

TIMER/PULSE

(MIN/SEC)

Forces relay OFF if changed. Affects which programming mode will be selected

if the MODE switch is pressed.

MODE Selects TIMER or PULSE SETUP mode depending on the position of the

TIMER/PULSE switch.

While in the NORMAL mode the controller will activate and deactivate the relay output based on the

current program the program type (Timer/Pulse) and the current time-of-day/day-of-week.

To support Daylight Savings Time the HR+ button will advance the time by one hour. A second

depression returns the time to the base time.

The MAN button may be used to force the relay ON or OFF.

To enter a programming mode press the MODE key. The unit will enter either the TIMER or PULSE

setup MODE based on the setting of the TIMER/PULSE switch.

3 / 6 © Ingram Products Inc 02/19/12

APT-9S

Programmable Timer

Quick Start Guide

Setting Day Ranges

The program times entered in the TIMER and PULSE setup modes may be applied to one or more days

of the week. Pressing the DAY button will cause the current day to flash. If the DAY is currently

enabled in will flash with a short 'off' time followed by a longer 'on' time. If the DAY is not enabled it

will flash with a long 'off' time followed by a shorter 'on' time. Pressing the MAN button will enable /

disable the current day. Multiple days of the week may be enabled for each time setting.

Pressing the DAY button again will move to the next day of the week. If a day of the week is enabled it

will be shown in the display. The DAY button may be cycled through the 7 days of the week. Each

programmed time may have a different day of the week setting.

TIMER SETUP Mode

The TIMER mode will turn the relay ON and OFF at specific times of the day. Different time

sequences may be defined for each day of the week (see setting day ranges). When the TIMER SETUP

mode is entered the display shows:

The MIN and SEC buttons allow setting the time that the Output will turn ON. Once a time has been

entered press the PROG button and the display will change to allow entering the time that the Output

will turn OFF.

After setting the OFF time press the PROG button again. The display will show the ON time for the

next program number. This process is repeated until all required program times have been entered. It is

not necessary to enter a sequence for each of the 80 possible program times.

To disable a program entry press the CLEAR. The display will show - - : - - to allow a new time to be

entered. Pressing the CLEAR again will retrieve the previous time. When the programming is

complete press the START button to return to the NORMAL mode.

This example shows the relay being turned on at 11:05 and turned off at

11:15 Monday – Friday.

4 / 6 © Ingram Products Inc 02/19/12

SU MO TU WE TH FR SA

ON – – : – – SET

Program Number

SU MO TU WE TH FR SA

OFF – – : – – SET

MO TU WE TH FR

ON 11 : 05 SET

MO TU WE TH FR

OFF 11 : 15 SET

APT-9S

Programmable Timer

Quick Start Guide

PU SE SETUP Mode

The PULSE mode will turn on the relay output for a fixed length of time (duration) at preset times of

the day. The duration may be programmed from 1 – 99.99 seconds. There may be 160 preset times

defined. When the PULSE SETUP mode is entered the display shows:

The MIN and SEC buttons allow setting the PULSE time (duration) that the relay contact will be ON.

After setting the PULSE time press the PROG button to select which program to change. Each

depression of the PROG button will advance the program number (1..160). The display will show:

The HOUR and MIN buttons may be used to set the time to activate the PULSE. The DAY button may

be used to select which days of the week the program should be active (see setting day ranges). To

disable a program entry press the CLEAR. The display will show - - : - - to allow a new time to be

entered. Pressing the CLEAR again will retrieve the previous time.

When the programming is complete press the START button to return to the NORMAL mode.

This example shows a P LSE will be generated at 4:15 on

Monday, Wednesday and Friday.

TWIN TIMER Mode

The TWIN TIMER mode disables the normal operating mode and sets the unit up to generate a cyclic

ON – OFF sequence. The ON and OFF times may be independently set. The TWIN TIMER mode is

entered by pressing the MODE button three times while in the NORMAL mode and then press the

PROG button. The display will show:

5 / 6 © Ingram Products Inc 02/19/12

– – : – – SET

SU MO TU WE TH FR SA

– – : – – SET

Program Number

ON – – : – – SET

TMR

MO WE FR

04 : 15 SET

APT-9S

Programmable Timer

Quick Start Guide

The times for the ON and OFF sequences may be specified in seconds/minutes or minutes/hours by

changing the TIMER/PULSE (MIN/SEC) switch. If the MIN position is selected (minutes/hours) the

MIN and HR buttons allow setting the times. If the SEC position is selected (seconds/minutes) the SEC

and MIN buttons allow setting the times.

After setting the ON time press the PROG button and the display will show:

After setting the OFF time press the START button to start the timer. The device will count down the

OFF time and then turn the relay on. It will then will count down the ON time and turn the relay off.

This cycle will repeat.

While in the DUAL TIMER mode the START button will toggle between running the cycle and

stopping the cycle. The output will be forced OFF when the timer is stopped.

Pressing the MODE switch will return the unit to the NORMAL (TIMER or PULSE) mode.

Holiday Setup Mode

The unit may be programmed to skip a set number of days. If the MODE button is pressed twice while

in the NORMAL mode the unit will enter the HOLIDAY SETUP mode.

The day to start skipping is selected by the DAY button which will cycle through each of the days of

the week. When the appropriate day is selected press the MIN key to select the number of days to

suspend the sequencing. Press the START button to return to the NORMAL mode.

Example shows 4 day holiday starting on Friday.

Ho : – – SET

Ho : 04 SET

OFF – – : – – SET

TMR

Inhaltsverzeichnis

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Tork

Tork TU40 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung