Ingrasys Osmium Bedienungsanleitung

User Manual

Osmium

This page intentionally left blank.

iii

Compliance Information

USA FCC Verication Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

fthis device may not cause harmful interference, and

fthis device must accept any interference received, including interference that may cause unde-

sired operation.

Class A

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec-

tion against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with manufacturer’s manual may cause harmful interference with radio com-

munications. Operation of this equipment in a residential area is likely to cause harmful interfer-

ence, in which case you will be required to correct the interference at your own expense.

Any modications made to this device that are not approved by Foxconn may void the authority

granted to the user by the FCC to operate this equipment.

ICES-003 Class A Notice - Avis NMB-003, ClasseA

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

CANADA INDUSTRY CANADA

This Class B (or Class A, if so indicated on the registration label) digital apparatus meets the

requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe B (ou Classe A, si ainsi indiqué sur l’étiquette

d’enregistration) respecte toutes les exigences du Reglement sur le Materiel Brouilleur du

Canada.

Japanese Voluntary Control Council for Interference (VCCI) statement

Australia and New Zealand Class A statement

Attention: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

CCC Class A Notice

The following statement is applicable to products shipped to China and marked with “Class A” on

the product’s compliance label.

European Union EMC Directive conformance statement

This product is in conformity with the protection requirements of EU Council Directive 2004/108/

EC on the approximation of the laws of the Member States relating to electromagnetic compat-

ibility. Foxconn cannot accept responsibility for any failure to satisfy the protection requirements

resulting from a non-recommended modication of the product.

This product has been tested and found to comply with the limits for Class A Information Tech-

nology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class

A equipment were derived for commercial and industrial environments to provide reasonable

protection against interference with licensed communication equipment.

Attention: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

EUROPE CE Declaration of Conformity

This product has been tested in accordance to, and complies with the European Low Voltage

Directive (2014/35/EU) and European EMC Directive (2014/30/EU).

The product has been marked with the CE Mark to illustrate its compliance.

This publication, including all photographs, illustrations and software, is protected under interna-

tained herein, may be reproduced without the express written consent of the manufacturer.

Version 1.0, 2017-08

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes

no representations or warranties with respect to the contents hereof and specically disclaims

any implied warranties of merchantability or tness for any particular purpose. Furthermore, the

manufacturer reserves the right to revise this publication and to make changes from time to time

in the content hereof without obligation to notify any person of such revision or changes.

Safety Information

Read this important safety information section. Retain this manual for reference. Read this sec-

tion before servicing.

Input rating: 200-240Vac, 7.5A, 50-60Hz

CAUTION:

To reduce the risk of electric shock, this server should only be serviced by qualied service personnel.

RTC Battery

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended

by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

CAUTION:

Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Rem-placer uniquement avec une

batterie du meme type ou d’un type recommande par le constructer. Metter au rebut les batteries usagees

conformement aux instructions du fabricant.

Laser Drive Equipment

The optical transceiver module in this server is a laser Class 1 product.

Ambient Operation

This equipment cannot be operated above an ambient operation temperature of 40 degrees

centigrade.

Equipment Location

This equipment can only be accessed by SERVICE PERSONNEL or by USERS who have been

instructed about the reasons for the restrictions applied to the location. Access is through the

use of a TOOL or lock and key, or other means of security, and is controlled by the authority

responsible for the location.

vii

Further Safety Information

Be sure to read all caution and danger statements in this documentation before performing the

instructions. Read any additional safety information that comes with your server or optional de-

vice before you install the device.

Safety Precautions

For your protection, observe the following safety precautions when setting up your equipment:

fFollow all cautions and instructions marked on the equipment.

fEnsure that the voltage and frequency of your power source match the voltage and frequency

inscribed on the equipment’s electrical rating label.

fNever push objects of any kind through openings in the equipment. Dangerous voltages may be

present.

fConductive foreign objects could produce a short circuit that could cause re, electric shock, or

damage to your equipment.

Safety Instructions

1. Please read these safety instructions carefully.

2. Please keep this Manual for later reference.

3. Please disconnect this equipment from AC outlet before cleaning. Don’t use liquid or sprayed

detergent for cleaning. Use moist sheet or cloth for cleaning.

4. For pluggable equipment, the socket-outlet must be installed near the equipment and must be

easily accessible.

5. Please keep this equipment from humidity.

6. Place this equipment on a safe reliable surface when installing. A drop or fall could cause injury.

7. Enclosure openings are for air circulation and protect the equipment from overheating. DO NOT

COVER THE OPENINGS.

8. Make sure the voltage of the power source matches rated voltages.

9. Place the power cord so that it won’t be stepped on or tripped over. Do not place anything on top

of the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect the equipment from outlet to avoid dam-

age to the system by transient voltages.

12. Do not spill liquids onto equipment; this may cause re or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should only be opened by quali-

ed service personnel.

14. If any of the following situations arises, have the equipment checked by qualied service:

a. The power cord or plug is damaged.

b. Liquid seeped into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well or operation does not match behavior described in user’s

manual.

e. The equipment has been dropped or damaged.

f. The equipment has obvious signs of damage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE TEMPERATURES EX-

CEED 60 °C (140 °F); IT MAY DAMAGE THE EQUIPMENT.

viii

Symbols

The following symbols will appear in this manual to indicate different safety precaution:

Hazardous voltages are present. To reduce the risk of electric shock and danger

to personal health, follow the instructions.

There is a risk of personal injury and equipment damage. Follow the instructions.

Hot surface. Avoid contact. Surfaces are hot and may cause personal injury if

touched.

Safety Statements

DANGER:

Electrical current from power, telephone, and communication cables is hazardous.

To avoid a shock hazard:

• Do not connect or disconnect any cables or perform installation, maintenance, or reconguration of this prod-

uct during an electrical storm.

• Connect all power cords to a properly wired and grounded electrical outlet.

• Connect to properly wired outlets any equipment that will be attached to this product.

• When possible, use one hand only to connect or disconnect signal cables.

• Never turn on any equipment when there is evidence of re, water, or structural damage.

• Disconnect the attached power cords, telecommunications systems, networks, and modems before you open

the device covers, unless instructed otherwise in the installation and conguration procedures.

• Connect and disconnect cables as described in the following table when installing, moving, or opening covers

on this product or attached devices.

To Connect: To Disconnect:

1. Turn everything OFF.

2. First, attach all cables to devices.

3. Attach signal cables to connectors.

4. Attach power cords to outlet.

5. Turn device ON.

1. Turn everything OFF.

2. First, remove power cords from outlet.

3. Remove signal cables from connectors.

4. Remove all cables from devices.

CAUTION:

When replacing the lithium battery, use only Foxconn Part Number XXXXX or an equivalent type battery rec-

ommended by The manufacture. If your system has a module containing a lithium battery, replace it only with

the same module type made by the same manufacturer. The battery contains lithium and can explode if not

properly used, handled, or disposed of.

Do not:

• Throw or immerse into water

• Heat to more than 100°C (212°F)

• Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

CAUTION:

When laser products (such as CD-ROMs, DVD drives, ber optic devices, or transmitters) are installed, note

the following:

• Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous

laser radiation. There are no serviceable parts inside the device.

• Use of controls or adjustments or performance of procedures other than those specied herein might result in

hazardous radiation exposure.

DANGER:

Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following.

Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid

direct exposure to the beam.

DANGER:

Class 1 Laser Product

Laser Klasse 1

Luokan 1 Laserlaite

Appareil A` Laser de Classe 1

CAUTION:

The following label indicates sharp edges, corners, or joints nearby.

CAUTION:

The following label indicates a hot surface nearby.

CAUTION:

The power control button on the device and the power switch on the power supply do not turn off the electrical

current supplied to the device. The device also might have more than one power cord. To remove all electrical

current from the device, ensure that all power cords are disconnected from the power source.

CAUTION:

Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label attached.

There are no serviceable parts inside these components. If you suspect a problem with one of these parts,

contact a service technician.

Attention: This server is suitable for use on an IT power distribution system whose maximum phase-to-

phase voltage is 240 V under any distribution fault condition.

DANGER:

Overloading a branch circuit is potentially a re hazard and a shock hazard under certain conditions. To avoid

these hazards, ensure that your system electrical requirements do not exceed branch circuit protection require-

ments. Refer to the information that is provided with your device for electrical specications.

CAUTION:

Do not place any object on top of rack-mounted devices.

Attention: This server is suitable for use on an IT power distribution system whose maximum phase-to-phase

voltage is 240 V under any distribution fault condition.

CAUTION:

Hazardous moving parts are nearby. Keep body parts away from moving part.

Inhaltsverzeichnis

Andere Ingrasys Server Handbücher

Ingrasys

Ingrasys FISC CDM Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung