INIM IC0020 Series Bedienungsanleitung
IC0020
Conventional resettable manual callpoint
ATTENTION!
IC0020 series manual call points are certified and approved according to EN54-11 -
Manual call points.
Description
IC0020 manual call points are specially designed to operate with
conventional control panels.
The device trigger element and red status LED are located in the
front case of the device. The LED will light up when the device is
activated.
The device details and information regarding the connection
terminals can be found on the label inside the device housing.
The device provides connectors for the resistance jumper. The
position of the jumper defines the alarm resistance, as follows:
The device package contains two fork-end keys which can be used
to open the housing and reset the device
The flush-mount backbox and the protective front plate are
accessory items and must be purchased separately.
Position Alarm resistance
RL 260 Ohm
RH 660 Ohm
A
Callpoint button - rear
B
Details label
C
Terminals
D
Backbox with fixing screw holes and cable entry
E
Fixed back-locking clips
F
Fixed back-locking clip positions
G
Back-locking backbox clips
H
Back-locking clip positions
I
Reset key slot
J
Protection front plate clips
K
Connectors for the resistance jumper
TECHNICAL SPECIFICATIONS
Operating voltage 10-30 Vdc
Resistance between terminals
“+” and “-” in the event of alarm 260 - 660 Ohm
Operating temperature -5°C / +40°C
Humidity
(without condensation) 95% RH
Dimensions (HxWxD) 84 x 84 x 45 mm
Weight 126 g
K
C
H
I
JJ
A
B
F
G
D
EE
F
DCMIIN4AIC0020-R100-20120924
0832-CPD-2053
991j/01
2
IC0020
Activation
The IC0020 manual callpoint uses a simple mechanism which consists of a rigid plastic operating element and an
over-center spring mechanism. Pressing on the black spot simulates “Break Glass” activation and triggers an alarm.
Activation is signalled by a yellow and black striped flag which drops into view on the upper part of the frontplate
and by solid light on the red LED.
Reset
The IC0020 manual call point is reset by inserting the key provided into the key slot and by pushing the trigger
mechanism upwards as far as possible, after which the key must be turned clockwise until the mechanism locks
back into position.
ATTENTION!
The reset procedure must be carried out in accordance with the above instructions,
otherwise, you may damage the manual call point and/or its key.
Successful rest causes the flag to withdraw and the red LED to go off.
Installation
Connect the IC0020 manual call point to the control panel
using 2 wires.
The backbox has standard wall-mount anchor screw holes.
Insert the forked-end of the reset key into the two slots and
push against the back-locking clips to open the manual call
point.
Once all the devices are installed, refer to the control panel
manual for the instructions relating to the configuration and
end-of-line resistance.
Test and maintenance
Test the manual call point immediately after installation and
then regularly during the periodic tests which must be
carried out in accordance with the local laws in force.
Warnings and limitations
IC0020 manual call point is not suitable for outdoor
installation unless adequately housed inside a heavy duty
weather proof box.
INIM Electronics reserves the right to change
the technical specifications of this product
without prior notice.
INIM Electronics s.r.l.
via Fosso Antico, Centobuchi
63033, Monteprandone, (AP) Italy
Tel. +39 0735 70 50 07
Fax + 39 0735 70 49 12
www.inim.biz [email protected]
Inhaltsverzeichnis
Andere INIM Sicherheitssystem Handbücher
INIM
INIM NRB100 Montageanleitung
INIM
INIM enea EC0020 Series Bedienungsanleitung
INIM
INIM NRB100 Montageanleitung
INIM
INIM smartliving series Bedienungsanleitung
INIM
INIM Sol-S Bedienungsanleitung
INIM
INIM snartliving Bedienungsanleitung
INIM
INIM Prime Betriebsanleitung
INIM
INIM PREVIDIA MICRO Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung