Inner Range M4 Kurzanleitung
Revision 1.0 January. 2001 1
M4 Interface.
P/No. 995070
INSTALLATION NOTES
The M4 Interface is used in conjunction with an Analogue Input Module and provides two functions for added system integrity.
An Analogue Module can support up to two M4 Interfaces.
The two functions of the M4 Interface are as follows:
1) Monitoring a Detector Supply voltage. The Detector supply is connected to an M4 Interface board. The voltage being
monitored is pre-scaled and two outputs are provided for connection to Inputs on an Analogue Module so that an alarm can be
generated if the voltage is outside the range of the preset upper and lower thresholds.
2) Provision of a monitored driver for a satellite siren.
A switched 13.8 V DC Siren output is provided.
The satellite siren is triggered by switching the siren output off, thus activating the siren, under any of the following conditions:
-Satellite siren connection is severed. (Cut or disconnected)
-Satellite siren cabinet tamper.
(If Satellite siren connection is wired in series with siren cover tamper switch)
-A specific Auxiliary on the Analogue Input Module is activated.
(i.e. Qxx:X01 for the first M4 Interface and Qxx:X02 for a second M4 interface if required)
A Siren Tamper output is also provided that can be monitored by a Digital Input on the Analogue Module.
Specifications
Supply Voltage: 16 V AC.
Siren Output Voltage: 13.8 V DC.
Optional backup Battery: 12V 6.5 AH Sealed Lead Acid battery.
“DET+” Threshold adjustment range: -25% to +25%.
Measurement error: +/- 150mV.
Siren output current: 2A Maximum.
Physical dimensions: Length: 140mm Width: 95mm
Installation environment: 0º to 40º Celsius
15% to 85% Relative humidity (non-condensing)
Control Module Firmware: V3 or later. (Memory configuration chosen must support Analogue Modules)
Parts List
-M4 Interface PCB assembly.
-Installation Kit in Plastic bag containing:
-1 x 6 Way Plug on Screw Terminal.
-1 x 3 Way Plug on Screw Terminal.
-2 x 2 Way Plug on Screw Terminals.
-2 x 4 Amp Fast Blow Fuse. M205
-Installation Manual. (This document)
Installation.
Installation environment should be maintained at a temperature of 0º to 40º Celsius and 15% to 85% Relative humidity (non-
condensing)
Board assembly physical dimensions: Length: 140mm Width: 118mm Height: 38mm
1. The M4 Interface board is supplied in kit form and is mounted in a suitable enclosure along with an Analogue Module PCB.
2. The 16 V AC supply, Satellite Siren, Analogue Module, optional Battery and Power Supply to be monitored are connected as per
the wiring diagrams on pages 2 & 3.
IMPORTANTNOTE.
Refer to the Analogue Module Installation Manual for details of additional connections and settings on the Analogue Module.
M4 Interface. Installation Notes.2
From Detector
Power supply to
be monitored.
LAN connection to
Control Module.
Siren-
Siren+
Optional 12V 6.5 AH
Battery connection.
16 V AC
Supply input.
Satellite Siren
connection.
+
-
A
B
< +
< -
Connection Details - Single M4 Interface.
Revision 1.0 January. 2001 3
Connection Details - Two M4 Interfaces.
DIN
AUX
ANAL1
ANAL2
0V
TB4
First M4 Interface.
DIN
AUX
ANAL1
ANAL2
0V
TB4
Second M4 Interface.
(Additional wiring on M4 Interface board as per detailed connection diagram opposite)
M4 Interface. Installation Notes.4
Designed & manufactured in Australia.
Due to on-going product development this manual is subject to change without notice.
© 2001. Part No: 635070 Revision 1.0.
Programming Notes. (Refer to the Programmer’s Manual for details)
The Input and Output numbers referred to in the following programming notes apply when the M4 Interface/s are connected
according to the wiring diagrams on pages 2 & 3.
Detector Supply Measurement and Monitoring.
1. MENU, 7, 2, 9. Program the Analogue Module noting the following:
-The calibration string for Zone 1 and 2 (& Zone 3 and 4 if a second M4 Interface is connected) must be 0225FA000000.
-Set the Z01 / Z03 Trigger 1 Value/s for the desired Upper Threshold of the Detector Voltage.
-Set the Z02 / Z04 Trigger 1 Value/s for the desired Lower Threshold of the Detector Voltage.
Refer to the following Table for examples of Trigger Value settings.
Upper Threshold Z01 &/or Z03
Trigger 1 Value Lower Threshold Z02 &/or Z04
Trigger 1 Value
%Voltage %Voltage
+5% 14.45 1445 -5% 13.1 1310
+10% 15.13 1513 -10% 12.38 1238
+15% 15.81 1581 -15% 11.69 1169
+20% 16.5 1650 -20% 11 1100
+25% 17.2 1720 -25% 10.31 1031
2. MENU, 7, 0. Program the Zone Inputs
(Qxx:Z01 and Z02 for the first M4 Interface and Qxx:Z03 and Z04 if a second M4 Interface is connected)
Note the following:
-Program an appropriate name for each Zone.
e.g. “DET+ Too High” for Zone 1. “DET+ Too Low” for Zone 2.
-Set the “Swap Seal and Alarm” option to YES for Zone 2 and Zone 4 (if used) only.
3. MENU, 7, 1. Program an Area to monitor the Analogue Input Zones and assign the Zones to the Area using an appropriate
Process Group in the normal manner.
Satellite Siren Driver Monitoring.
1. MENU, 7, 0. Program the Zone Input
(Qxx:Z05 for the first M4 Interface and Qxx:Z06 if a second M4 Interface is connected)
Note the following:
-Program an appropriate name. e.g. “Satellite Siren Tamper”.
-Set the “Swap Seal and Alarm” option to YES.
2. MENU, 7, 1. Program an Area to monitor the Siren Tamper Zone/s and assign the Zone/s to the Area using an appropriate Process
Group in the normal manner.
REFER TO THE ADVANCED TECHNICAL SUPPPORT SECTION OF THE WEBSITE
FOR DETAILED PROGRAMMING INSTRUCTIONS IF REQUIRED.
www.innerrange.com.au/techsupp.html
Inhaltsverzeichnis
Andere Inner Range Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
