InnoPrint CR-158 Bedienungsanleitung

InnoPrint Limited assume no responsibility for errors, omissions, or damages

resulting from the use of information contained within this manual.

CR-158

COUPON PRINTER

MANUAL

CR-158 Coupon Printer Manual 2

MANUAL AMENDMENTS

Rev.

Date

Amendment Details

Issued by

1.0

01-11-13

First Issue

2.0

28.04.14

Updated to include new bezels

CR-158 Coupon Printer Manual 3

CR-158 COUPON PRINTER MANUAL

MANUAL AMENDMENTS 2

LIMITED WARRANTY 4

PRODUCT SAFETY INFORMATION 4

1. INTRODUCTION 5

2. CONNECTING THE PRINTER

2.1.Power & pulse connection 5

2.2.USB data connection 6

2.3.Serial connection 6

3. DIP SWITCHES, BUTTONS & STATUS LEDS

3.1.Dip switches 6

3.2.Buttons 6

3.3.LED status lights 6

3.4.LED error status lights 7

4. BEZEL OPTIONS

4.1.US Bezel 7

4.2.EUR Bezel 7

5. TECHNICAL SPECIFICATIONS

DC Voltage 8

Supply current 8

Interface logic levels 8

Functionality 8

Performance 8

Environment 9

6. FIELD SERVICE

6.1 Inserting a role of paper 9

6.2 Removing the paper guide 9

6.3 Removing the print head roller assembly 10

6.4 Micro SD card slot and battery compartment 10

7. CREATING TEMPLATES & TESTING

7.1 Ticket Template Manger 11

8. DIAGRAM

8.1 CR-158 with US bezel 12

8.2 CR-158 with EUR bezel 13

CR-158 Coupon Printer Manual 4

may be reproduced in any form or by any means or used to make any derivative such

as translation, transformation, or adaptation without permission from InnoPrint

Limited. The contents of this manual set may be subject to change without prior

notice.

LIMITED WARRANTY

InnoPrint Limited warrants each of its hardware products to be free from defects in

workmanship and materials under normal use and service for a period commencing

on the date of purchase from InnoPrint Limited or its Authorized Reseller, and

extending for the length of time stipulated by InnoPrint Limited.

A list of InnoPrint Limited offices can be found in every section of this manual set. If

the product proves defective within the applicable warranty period, InnoPrint Limited

will repair or replace the product. InnoPrint Limited shall have the sole discretion

whether to repair or replace, and any replacement product supplied may be new or

reconditioned.

The foregoing warranties and remedies are exclusive and are in lieu of all other

warranties, expressed or implied, either in fact or by operation of law, statutory or

otherwise, including warranties of merchantability and fitness for a particular purpose.

InnoPrint Limited shall not be liable under this warranty if it’s testing and examination

disclose that the alleged defect in the product does not exist or was caused by the

customer's or any third person's misuse, neglect, improper installation or testing,

unauthorized attempts to repair, or any other cause beyond the range of the intended

use. In no event will InnoPrint Limited be liable for any damages, including loss of

profits, cost of cover or other incidental, consequential or indirect damages arising out

the installation, maintenance, use, performance, failure or interruption of an InnoPrint

Limited product, however caused.

PRODUCT SAFETY INFORMATION

Throughout this manual set, we may draw your attention to key safety points that you

should be aware of when using or maintaining the product.

These safety points will be highlighted in

a box, like this:

Caution!

Mains voltage is present on

these terminals

This manual set and the information it contains is only applicable to the model stated

on the front cover, and must not be used with any other make or model.

CR-158 Coupon Printer Manual 5

1. INTRODUCTION

Purpose of this document

The purpose of this document is to aid in the set-up of, and software integration for

the InnoPrint CR-158 Printer.

2. CONNECTING THE PRINTER

The printer has three available connections, either via the 7 pin connector, USB or

RJ45 socket.

2.1 Power and Pulse Connection

The large, 7-pin connector at the centre of the rear of the device is used for power

and to control the device via a pulse interface. On the female side of the connector

(i.e. on the device itself) from left to right, the pins are:

1 –Red –+12-24V DC

2 –Black –Ground

3 –Brown –Coin In Pulse Signal

4 –Orange –Note In Pulse Signal

5 –Yellow –Pay out Trigger Pulse Signal

6 –Green –Ticket Out Output (currently unused)

7 –Blue –Error Out Output (currently unused)

CR-158 Coupon Printer Manual 6

2.2 USB Data Connection

The USB connection is used to host a COM port on a connected PC, allowing the

device to be communicated with through the SSP protocol. Information on this

protocol can be found in a separate document (Innovative Technology manual

GA138.) SSP can be used to configure and control the device, as well as to download

certain files onto the device via the SSP update process. The device is connected in

this way like any other USB peripheral, and no special cables should be required

2.3 Serial connection (RJ45 like connection)

This connector is used for Pot o’ Gold communications

3. DIP SWITCHES, BUTTONS & STATUS LEDS

3.1 Dip Switches

Currently dip switches 1-3 are unused.

Dipswitch 4 controls the cut mode of the printer guillotine. If the dip switch is in the

down (off) the printer will performs a half cut. This will leave a small tab attached to

the rest of the roll, and requiring a small amount of force to pull the coupon away.

In the up (on) position, the printer performs a full cut and fully detaches the printed

coupon from the rest of the roll.

3.2 Buttons

Button 1 (left) is used to test the printer. Holding the button 1 down for 4 seconds will

cause the device to print a test ticket. As well as testing the print head, the test ticket

also includes a report containing some basic configuration information about the

device. Button 2 (right) is not currently used.

3.3 LED Status Lights

The device has 3 LEDs - green, yellow and red - which are used to display the status

of the device. The standard statuses are displayed as follows:

Slow pulsing yellow

Printer idle

Slow pulsing yellow and solid red

Printer idle, paper low

Slow pulsing green

Printer idle, SSP enabled

Slow pulsing green and solid red

Printer idle, SSP enabled, paper low

Fast pulsing green

Printing

Fast pulsing green, yellow, red

Printer initialising after power off/reset

CR-158 Coupon Printer Manual 7

3.4 LED Error Status Lights

The LEDs are also used to display error states. These are shown by a number of slow

red flashes, followed by a number of yellow flashes. The number of each colour of

flash indicates the error as shown in the table below:

4. BEZEL OPTIONS

There are currently two types of bezel available, see below;

4.1 US Bezel:

4.2 EURO: Bezel:

Note: When ordering the CR-158 printer, ensure you indicate which bezel you require,

i.e. for the US bezel, please order as CR-158/U and CR-158/E for the EURO bezel.

Red

Yellow

No Paper

Unknown Error

Initialisation Fail

No Print Head

Load Fail

Cut Fail

Unknown Jam

CR-158 Coupon Printer Manual 8

5. TECHNICAL SPECIFICATIONS

CR-158

DC Voltage

Minimum

Nominal

Maximum

Absolute limits

11 V

12 V

26 V

Supply ripple voltage

0 V

0.5 V @ 100 Hz

Supply Current

Standby

100 mA

Printing

2 A

Peak

4.8 A

Interface Logic Levels

Logic Low

Logic High

Inputs

0 V to 0.5 V

+3.7 V to +12 V

Outputs (2.2 kΩ pull-up)

0.6 V

Pull-up voltage of host

interface

Maximum current sink

50 mA per output

Functionality

Printing Method

Direct Thermal Printing

Dot Pitch

0.125 mm

Resolution

384 dots per line

Print Width

48mm

Print Speed

100mm/s

Ticket Print and

Present

< 3 Seconds

Barcode Types

Interleaved 2 of 5, others by request

Graphic resources

2MB on-board SPI Flash. An micro SD card slot is

available for storage of extra fonts and images

Interface: User

Ticket print button, Feed button, 4 dip-switches.

LEDs: Ready, Paper, Fault

Interface: Protocols

eSSP, Pot o’ Gold

Interface: Electrical

Open collector, True RS232, USB

Interface: Physical

USB (direct to printer)

7 –way power, pulse and “Pot O Gold”

RJ45 serial connector

Support tools

The firmware and interface protocol are

upgradeable via USB. Ticket Template Manager

software allows design of own ticket templates

CR-158 Coupon Printer Manual 9

Environment

Parameter

Min

Max (Design Guide)

Operating

temperature

(Ambient)

+5°C

+60°C

Humidity

95% Non Condensing

6. FIELD SERVICE

6.1 Inserting A New Roll Of Paper

To insert a new roll of paper, remove the roll mandrel from the printer, insert into the

roll core and place into the holder on the printer so the paper comes off the role and

into the printer mechanism as shown in the below images.

Feed the paper into the mechanism with the unit powered on, when the paper

triggers the sensor the unit will auto-feed the paper. Remove the excess paper when

the unit has completed the paper feed.

If required, you can now do a test print, by holding the left hand button for 4

seconds.

6.2 Removing The Paper Guide

The paper guide can easily be removed by pulling up

on the guide using the tab at the top of the guide. With

the guide removed, this allows easy access to remove

paper that has become jammed, or for access for cleaning.

CR-158 Coupon Printer Manual 10

6.3 Removing The Print Head Roller Assembly

The print head roller assembly can easily be removed to allow easy access for

cleaning and removal of jammed paper. Firstly remove the paper guide, as detailed in

6.2, then pull the release handle in the direction shown in the picture. This will also

release the paper from the mechanism. To reinsert the roller assembly just click back

into place.

Note: Fit the roller assembly before reinserting the paper guide and paper roll.

6.4 Micro SD Card Slot & Battery Compartment

The micro SD card slot and battery compartment are located on the left hand side of

the unit. The battery is accessed via the removable cover.

Inserting a micro SD card expands the memory of the printer, allowing extra fonts,

images and coupon templates to be stored.

The battery powers the units internal real time clock, which can be used to provide

and date and time stamp on coupons.

Note: Battery Type: CR1225, 3 Volt, 50mAh (BA00100)

Andere Handbücher für CR-158

Inhaltsverzeichnis

Andere InnoPrint Drucker Handbücher

InnoPrint

InnoPrint CR-158 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung