Innova 3.0 Bedienungsanleitung
Instructions 1 di 4 cod. N420000A - 03
INSTRUCTIONS FOR INNOVA
3.0 ATOMIZER
1. Characteristics
Instructions 2 di 4 cod. N420000A - 03
2. Unpacking
After verifying the integrity of the package, open the shipping carton and remove the polystyrene
protection; then remove the atomizer. Access to the unit is only permitted to specialized personnel.
3. Hydraulic connections
Before proceeding with the hydraulic connections, check that the atomizer is not plugged in.
4. Water supply connection
The atomizer has a superior hole on the top cover for pipes with outside diameter of 13mm.
Insert the condensate pipe in the upper hole and check that it enters into the atomizer for at least
30 mm.
5. Water mist connections
The atomizer 3.0 already has a 80 mm diameter fitting for ejecting atomized water. This connection
can be extended with normal pipe (80 mm diameter).
Ensure that these extensions have a slope of at least 3 ° to let in the atomizer any condensate
water in the tube and that the output connection is free from any obstacles for a distance of 50 cm.
Avoid excessive stress on the atomizer output connection.
6. Installation template
When installing atomizer near the wall for the expulsion of water on the outside, drill a hole of 82
mm diameter on the wall as picture below.
Instructions 3 di 4 cod. N420000A - 03
7. Electrical connections
8. Functioning
3.0 atomized water by wave propagation generated by piezoelectric cells 10 in the direction of the
water surface. On the free surface of the water, generate droplets of small dimensions, which are
removed by forced ventilation.
3.0 has level floating that keep constant the amount of water above the piezoelectric cells to
maintain a high performance for the condensate.
The atomizer goes on standby automatically if the water level falls below the minimum level and
automatically activates the heating cable (optional) when the water temperature falls below 3 ° C.
3.0 has a CP contact to interface with the ..2.0 air conditioner when there is any failure or
malfunctions.
CP contact to be
connected to 2.0
air conditioner
230 V AC
power supply
Instructions 4 di 4 cod. N420000A - 03
9. Season change procedure
It is very important to follow the procedure outlined in this paragraph to avoid a systematic
alarm of the combination ..2.0 + 3.0 and the possible failure of the nebulizer.
This procedure, enabled through the display of the air conditioner, modifies the default settings of
the drain pan of the appliance by disabling its automatic closure during the summer season. This
procedure is used to avoid that during the summer season, with the opening of the drain valve of
the drain pan, the condensate itself is poured all in the 3.0 nebulizer installed under the appliance.
To activate this function:
-Press the cooling mode key on the display of the ..2.0 for 15 sec.
-The symbol “En” will appear
-Press again for 15 sec. the key
-The symbol “ds” will appear
-Let the display go back to the main screen
The condensate drain will always remain open in both seasons, guaranteeing a regular flow of
condensation.
To set the default function again, follow the same procedure and select "En".
10. Led and buzzer
The device is equipped with some light and sound signals that indicate the status and any
malfunctions:
•GREEN LED: atomizer power supply on
•ORANGE LED: atomizer running
•RED LED: atomizer in stand-by and electrical heater on
•BLINCKING RED-GREEN LED + BUZZER: alarm
The reasons for alarms may be the following:
•maximum level sensor activated
•level sensors wrong (for example the maximum level sensor is busy when normal level
sensor is off)
•bad indication of condensate temperature
Inhaltsverzeichnis
Andere Innova Klimaanlage Handbücher
Innova
Innova IGZCAPS NI Series Bedienungsanleitung
Innova
Innova IGZC09NI-1 Bedienungsanleitung
Innova
Innova Air Leaf ESE645 Bedienungsanleitung
Innova
Innova 2.0 10 HP Bedienungsanleitung
Innova
Innova Innova Filomuro Incasso SLWI Bedienungsanleitung
Innova
Innova 2.0 Service-Handbuch
Innova
Innova IGZM218NO-1 Bedienungsanleitung
Innova
Innova IGZC09NI/O-1 Bedienungsanleitung
Innova
Innova Filomuro SWI 400 Bedienungsanleitung
Innova
Innova Filomuro SLW Series Bedienungsanleitung
Innova
Innova 2.0 Bedienungsanleitung
Innova
Innova AirLeaf SL Bedienungsanleitung
Innova
Innova 607NT Montageanleitung
Innova
Innova IGPCX-35-1 Bedienungsanleitung
Innova
Innova gazuno bee 600 Bedienungsanleitung
Innova
Innova IGPCX-27-1 Bedienungsanleitung
Innova
Innova IGZF09NO-1 Bedienungsanleitung
Innova
Innova 2.0 Bedienungsanleitung
Innova
Innova 2.0 Bedienungsanleitung
Innova
Innova X90NI Bedienungsanleitung
