Innovative Technology Smart Coin System Bedienungsanleitung

SMART Coin

System

QUICK START

AND

CONFIGURATION

GUIDE

SMART Coin System Quick Start and Configuration Guide 2

SMART Coin System Quick Start and Configuration Guide

1INTRODUCTION 4

2ASSEMBLY 5

2.1 Detaching SMART Coin Feeder 6

2.2 Baseplate Mounting Requirements 7

2.3 Fit the payout nozzle to the SMART Coin System 8

2.4 Opening the SMART Coin System 9

3CONNECTORS AND PINOUTS 10

3.1 Connections 10

3.2 Operational Connection 10

4CONFIGURATION 12

4.1 Configuration Button Functions 12

4.2 Flash Counts (Interface Type) 13

4.3 DES Trusted Mode 13

5PROGRAMMING AND DATASET LOADING 14

5.1 SD Card Update 14

6TECHNICAL SPECIFICATIONS 15

6.1 Electrical Specification 15

6.2 Interface Specification 15

6.3 Dimensions 16

6.4 Outline Dimensions 16

6.5 Mounting Face Dimensions 16

6.6 Mounting Screws 17

7SMART COIN SYSTEM FAULT CODES 17

SMART Coin System Quick Start and Configuration Guide 3

7.1 Flash Fault Codes 17

8MAINTENANCE 18

8.1 Cleaning 18

8.2 Disk Removal 19

8.3 Clearing a Jam 20

9FREQUENTLY ASKED QUESTIONS 21

10 DIARY OF CHANGES 22

SMART Coin System Quick Start and Configuration Guide 4

1Introduction

This manual is intended to help with first setup and installation of the SMART Coin

System.

This section contains the essential information that a user needs to quickly assemble

and configure the SMART Coin System ready for installation into the host machine or

for testing on the bench.

SMART Coin System Quick Start and Configuration Guide 5

2Assembly

Install: Attaching Smart Coin Feeder to SMART Hopper

Machine Type: Access to front –in order to allow access

Entry: Pay-in Chute

1. Place the feeder on top of the hopper ensuring the feeder is overhanging by

approximately 4cm so as to line up with the latches on the top of the smart

hopper.

2. Slide the Feeder forward until it locks securely in place.

3. Slide the now assembled SMART Coin System on to the base plate the latch will

lock the SMART Coin System in to place.

SMART Coin System Quick Start and Configuration Guide 6

2.1 Detaching SMART Coin Feeder

The below pictures highlight the button location to detaching the different parts.

1. The Feeder can be detached from the Hopper pulling up the button.

2. Then remove the Feeder by reversing the process of attaching.

3. Push the Feeder back until it stops and lift the Feed from the Hopper.

SMART Coin System Quick Start and Configuration Guide 7

2.2 Baseplate Mounting Requirements

Ensure that the mounting position and note exit hole meets the dimensional

requirements as shown below (all dimensions are in millimetres mm):

The coins fall from the cashbox exit chute and are intended to be caught in the host

machine cashbox.

The maximum thickness of the shelf (on to which the baseplate is mounted) is 10mm

–including any items which protrude below it (such as nuts, washers, screws etc.).

WARNING!

Ensure there is space for

coins to fall clear.

Ensure that there is space below the exit chute to

allow the coins to fall clear of the coin exit.

SMART Coin System Quick Start and Configuration Guide 8

Secure the baseplate in position using the screw holes provided. See the Specification

section 6.6 for a specification on the screws to be used.

WARNING!

Ensure baseplate mounting

screws are flush with the

surface of the baseplate.

Do not allow screw heads to foul the SMART Coin

System.

2.3 Fit the payout nozzle to the SMART Coin System

Place nozzle hooks in to the Hopper with Feeder removed. Then push down on the

Nozzle it clip in to place.

WARNING!

Ensure the Nozzle is

firmly clipped and

latched

SMART Coin System Quick Start and Configuration Guide 9

2.4 Opening the SMART Coin System

The SMART Coin

System and be

opened via the front

latch.

Take care during opening any

loose coins not captured by the

disk will be free to fall once the

SMART Coin System is separated.

Coin Disk

Sensor Coils

& Acoustic

flap

Coin

Transport

Path

Sensors

Acceptance

Flap

SMART Coin System Quick Start and Configuration Guide 10

3Connectors and Pinouts

3.1 Connections

There is only one connecting plug on the SMART Coin System for use by the host. It

is located on the rear of the baseplate please use the connector labelled SSP. The CCT

is legacy connection for use when the hopper is used in the SMART Hopper

configuration for attaching external ccTalk coin accepter. The USB port is primarily for

use during servicing and engineers use.

WARNING!

Do not attempt disassembly

Do not attempt to disassemble the SMART Coin

System –trying to do this could cause personal

injury and will void the warranty.

3.2 Operational Connection

Andere Handbücher für Smart Coin System

Inhaltsverzeichnis

Andere Innovative Technology Geldzähler und Münzsortierer Handbücher

Innovative Technology

Innovative Technology SMART Hopper Bedienungsanleitung

Beliebte Geldzähler und Münzsortierer Handbücher anderer Marken

Coinco

Coinco Guardian 6000 Montage- und Bedienungsanleitung

Hyundai MIB

Hyundai MIB SB-2000 Bedienungsanleitung

Royal Sovereign

Royal Sovereign RBC-2100 Bedienungsanleitung

Peradon

Peradon DCT Bedienungsanleitung

Beckmann

Beckmann EMS-58 Bedienungsanleitung

MEI

MEI Economy Series Bedienungsanleitung

Safescan

Safescan 1450 Bedienungsanleitung

Hamilton Manufacturing Corporation

Hamilton Manufacturing Corporation Audit Pro 2000 Kurzanleitung

Alberici

Alberici EP-1P0S Bedienungsanleitung

PRO Intellect Technology

PRO Intellect Technology PRO CS-80E Bedienungsanleitung

Alberici

Alberici AL66 FG modifiable ccTalk Bedienungsanleitung

Inepro

Inepro Multi Connectivity Box Bedienungsanleitung

Standard Change-Makers

Standard Change-Makers MC Series Bedienungsanleitung

Safescan

Safescan 1250 SGD Bedienungsanleitung

Alberici

Alberici Hammer Two Bedienungsanleitung

Money Control

Money Control SR3 Bedienungsanleitung

Ribao

Ribao CS-600A Bedienungsanleitung

Coinco

Coinco Guardian GLX Series Original Betriebsanleitung