Inspur NF5888M5 Bedienungsanleitung

Inspur Server User Manual

NF5888M5 (AGX-5)

V1.1

No part of this document may be reproduced or transmitted in any form or by any means

without prior written consent of Inspur.

The information in this manual is subject to change without notice.

Inspur is the registered trademark of Inspur. All the other trademarks or registered

trademarks mentioned in this manual are the property of their respective holders.

Edion:1.1

Sep.2019

Abstract

This manual contains technical informaon such as specicaons, hardware operaons,

soware conguraon, fault diagnosis, etc., that are relevant to the maintenance and

operaon of this server.

It is recommended that server installaon, conguraon and maintenance is performed by

experienced technicians only.

Target Audience

This manual is intended for:

●Technical support engineers

●Product maintenance engineers

●Technicians

Warnings:

This manual introduces the NF5180M5 server’s technical features, system installaon and setup,

which will help the user to understand how best to ulize the server and all its funconalies.

1.For your safety, please do not disassemble the server’s components arbitrarily. Please do

not extend conguraon or connect other peripheral devices arbitrarily. If needed, please

contact Inspur for our support and guidance.

2.Before disassembling the server’s components, please be sure to disconnect all the power

cords connected to the server.

3.BIOS and BMC setup is a signicant factor in correctly conguring your server. If there are

no special requirements, it is suggested to use the Default Values and not alter the parameter

sengs arbitrarily. Aer the rst login, please change the BMC user password in me.

4.Please install the product-compable operang system and use the driver provided by

Inspur. If you use an incompable operang system or non-Inspur driver, it may cause

compability issues and aect the normal use of the product, Inspur will not assume any

responsibility or liability.

Inspur is not responsible for any damages, including loss of prots, loss of informaon,

interrupon of business, personal injury, and/or any damage or consequenal damage

without limitaon, incurred before, during, or aer the use of our products.

Contents

1 Safety Instructions......................................................................................................................... 1

2 Product Specification .................................................................................................................... 5

2.1 Overview .................................................................................................................................... 5

2.2 Features and specifications ........................................................................................................ 5

3 Component identification.............................................................................................................. 7

3.1 Front panel components ............................................................................................................ 7

3.2 Front control panel buttons and indicators................................................................................ 8

3.3 Hard drive tray indicators ........................................................................................................... 8

3.4 Rear panel components.............................................................................................................. 9

3.5 Motherboard components ......................................................................................................... 10

4 Operations..................................................................................................................................... 13

4.1 Power up the server ................................................................................................................... 13

4.2 Power down the Server .............................................................................................................. 13

4.3 Extend the server from the rack................................................................................................. 13

4.4 Remove the access panel ........................................................................................................... 14

4.5 Install the access panel............................................................................................................... 15

4.6 Install the server......................................................................................................................... 15

5 Setup ............................................................................................................................................. 17

5.1 Optimum environment............................................................................................................... 17

5.2 Rack warnings............................................................................................................................. 19

5.3 Identifying the contents of the server shipping carton ..............................................................20

5.4 Installing hardware options........................................................................................................ 20

5.5 Installing the server into the rack............................................................................................... 20

5.6 Installing the operating system .................................................................................................. 21

6 Hardware options installation ....................................................................................................... 22

6.1 Overview .................................................................................................................................... 22

6.2 Processor option......................................................................................................................... 22

6.3 Memory option .......................................................................................................................... 24

6.4 Hard drive option ....................................................................................................................... 26

6.5 Power supply option................................................................................................................... 27

6.6 Air baffle option ......................................................................................................................... 28

7 Cabling........................................................................................................................................... 30

8 BIOS setup ..................................................................................................................................... 32

8.1 Common operations................................................................................................................... 32

8.2 BIOS parameter description ....................................................................................................... 50

8.3 Firmware update ........................................................................................................................ 92

9 BMC settings.................................................................................................................................. 97

9.1 Motherboard BMC settings ........................................................................................................ 97

9.2 Switch board BMC settings......................................................................................................... 125

10 Common faults and troubleshooting........................................................................................... 152

10.1 Hardware problems.................................................................................................................. 152

10.2 Software problems ................................................................................................................... 155

11 Battery replacement.................................................................................................................... 157

12 Regulatory compliance notices ................................................................................................... 158

12.1 Regulatory compliance identification numbers........................................................................ 158

12.2 Federal communications commission notice ........................................................................... 158

12.3 European Union regulatory notice ........................................................................................... 159

12.4 Disposal of waste equipment by users in the European Union................................................159

12.5 Korean notice ........................................................................................................................... 160

12.6 Chinese notice .......................................................................................................................... 160

12.7 Battery replacement notice...................................................................................................... 160

13 Electrostatic discharge................................................................................................................. 162

13.1 Preventing electrostatic discharge ........................................................................................... 162

13.2 Grounding methods to prevent electrostatic discharge........................................................... 162

14 Warranty...................................................................................................................................... 163

14.1 Introduction.............................................................................................................................. 163

14.2 Warranty service ...................................................................................................................... 163

14.3 Warranty exclusions ................................................................................................................. 164

Safety Introductions

1. Safety instructions

WARNING: Please be advised to follow the instructions below for safety. Failure to do so

could result to potential dangers that may cause property loss, personal injury or death.

1. The power supplies in the system may produce high voltages and energy hazards that

may cause personal injury. For your safety, please do not attempt to remove the cover

of the system to remove or replace any component without assistance provided by

Inspur. Only service technicians trained by Inspur are authorized to remove the cover of

the host, and to remove and replace internal components.

2. Please connect the equipment to the appropriate power sup0ply. Use only power supplies

with the correct voltage and electrical specifications according to the label. To protect your

equipment from damages caused by a momentary spike or plunge of the voltage, please

use relevant voltage stabilizing equipment, or uninterruptible power supplies.

3. If you must use an extension cable, please use a three-core cable with properly

grounded plugs. Observe extension cable ratings. Ensure that the total rating of all

equipment plugged into the extension cable does not exceed 80 percent of the ratings

limit for the extension cable.

4. Please be sure to use the power supply components that come with the server, such as

power lines, power socket (if provided with the server) etc. For your safety, please do

not replace power cables or plugs randomly.

5. To prevent electric shock dangers caused by leakage in the system, please make sure

that the power cables of the system and peripheral equipment are correctly connected

to the earthed/grounded power socket. Please connect the three-core power line plug

to the three-core AC power socket that is well earthed and easy to access. Be sure

to use earthing /grounding pin of power lines and do not use the patch plug or the

earthing/grounding pin unplugged with cables. In the case that the earthing/grounding

conductors are not installed and it is uncertain whether there are appropriate earthing/

grounding protections, please do not use or attempt to operate the equipment. Contact

and consult an electrician.

6. Please do not push any objects into the openings of the system. Doing so may cause

fire or electric shock.

7. Please place the system far away from the cooling plate and heat sources, and be sure

not to block the air vents.

8. Please be sure not to scatter food or liquid in the system or on other components, and

do not use the product in humid or dusty environments.

9. Using an incompatible battery may cause explosion. When battery replacement is

required, please consult the manufacturer first, and choose batteries of the same or

equivalent type. Do not disassemble, crush, puncture the batteries or make the external

connection point short circuit, and do not expose them in the environment over 60°C.

Never throw batteries into fire or water. Please do not attempt to open or repair the

batteries. Dispose of used batteries according to instructions. For battery recycling,

please contact the local waste recycling center.

10. Before installing equipment into the rack, please install all front and side stabilizers on

the independent rack first. Please install the front stabilizers first, if connecting with

other racks. Please install stabilizers before installing equipment into the rack. Failure to

install the corresponding stabilizers before installing equipment into the rack may cause

the cabinet to tip over, possibly resulting to severe injury. After installing the equipment

and other components into the rack, only one component can be pulled out from the

rack through its sliding part at one time. Pulling out several components at the same

time may cause the rack to turn over, resulting to serious personal injury.

11. A minimum of two people are required to safely move a rack. The racks are extremely

awkward and heavy, moving them without adequate, trained personnel could result in

severe injury or death.

12. It is prohibited to directly short-circuit the copper busbar. Please do not touch the

copper busbar when the rack is powered on.

13. This is Class A product, and may cause radio interference. In such case, users may need

to take necessary measures to mitigate the interference.

14. The equipment is intended for installation in a Restricted Access Location.

Note: The following considerations may help avoid the occurrence of problems that could

damage the components or cause data loss, etc.

1. In the event of the following, please unplug the power line plug from the power socket

and contact Inspur’s customer service department:

1) The power cables, extension cables or power plugs are damaged.

2) The products get wet.

Safety Introductions

3) The products have fallen or have been damaged.

4) Other objects have fallen into the products.

5) The products do not or are unable to function normally even when attempting to

operate according to the instructions.

2. If the system becomes wet or damp, please follow these steps:

1) Power off the equipment, disconnect them with the power socket, wait for 10 to 20

seconds, and then open the host cover.

2) Move the equipment to a well-ventilated place to dry the system at least for 24 hours

and make sure that the system is fully dried.

3) Close the host cover, reconnect the system to the power socket, and then power on.

4) In case of operation failure or other abnormal situations, please contact Inspur and get

technical support.

3. Pay attention to the position of system cables and power cables-avoid placing wires in

high foot traffic locations. Please do not place objects on the cables.

4. Before removing the host cover, and/or touching the internal components, please

allow for the equipment to cool first. To avoid damaging the mainboard, please power

off the system and wait for five seconds, and then remove the components from the

mainboard and/or disconnect the peripheral device from the system. Please remember

that only service technicians trained by Inspur are authorized to remove the cover of

the host, and to remove and replace internal components.

5. If there is modem, telecom or LAN options installed in the equipment, please pay

attention to the followings:

1) In the case of thunder and lightning, please do not connect or use the modem.

2) Never connect or use the modem in a damp environment.

3) Never insert the modem or telephone cables into the socket of network interface

controller (NIC).

4) Before unpacking the product package, installing internal components, touching

uninsulated cables or jacks of the modem, please disconnect the modem cables.

6. In order to prevent electrostatic discharge from damaging the electronic components in

the equipment, please pay attention to the followings:

1) Please remove any static electricity on your body before dismounting or touching any

electronic component in the equipment, to prevent the static electricity from conducting

itself to the sensitive components. You may remove the static electricity on the body by

touching the metal earthing objects (such as the unpainted metal surface on the rack).

2) Please do not take electrostatic sensitive components that are not ready to be installed

for application out of the antistatic package materials.

3) While working, please touch the earthing conductor or the unpainted metal surface on

the cabinet regularly to remove any static electricity from the body that may damage

the internal components.

7. Upon receiving the proper authorization from Inspur and dismounting the internal

components, please pay attention to the following:

1) Switch the system power supply off and disconnect the cables, including all connections

of the system. When disconnecting the cables, please hold the connector of the cables

and slowly pull the plugs out. Never pull on the cables.

2) The products need to completely cool down before dismounting the host cover or

touching the internal components.

3) During the dismounting process, avoid making large movement ranges to prevent

damage to the components or scratching arms.

4) Handle components and plug-in cards with care. Please do not touch the components

or connection points on the plug-in cards. When handling the plug-in cards or

components, firmly grab the edges of the plug-in cards and components, and/or their

metal fixed supports.

8. During the process of rack installation and application, please pay attention to the followings:

1) After the rack installation is finished, please ensure that the stabilizers have been fixed

to the rack and supported to ground, and the weight of the rack is firm on ground.

2) Always load from the bottom up, and load the heaviest items first.

3) When pulling out the components from the rack, apply slight force to keep the rack balanced.

4) When pressing down the release latch and the rail of components is sliding, please be

careful; as the sliding may hurt your fingers.

5) Do not overload the AC power supply branch circuits in the rack. The total load of the

rack should not exceed 80% of the ratings of the branch circuits.

6) Ensure that components in the rack have good ventilation conditions.

7) When repairing components in the rack, never step on any other components.

9. After receiving the server, please refer to the label on the top cover to remove the shipping

screws on both sides of the chassis and then install it on the rack, to avoid damage to the

handles when you open the GPU BOX later without removing the screws.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Inspur Server Handbücher

Inspur

Inspur NF5180M4 Bedienungsanleitung

Inspur

Inspur NF8380M5 Bedienungsanleitung

Inspur

Inspur Yingxin NX 5440 Bedienungsanleitung

Inspur

Inspur NF5280M6 Bedienungsanleitung

Inspur

Inspur NF5488M5 Bedienungsanleitung

Inspur

Inspur Tiansuo TS860 Bedienungsanleitung

Inspur

Inspur NP5540M3 Bedienungsanleitung

Inspur

Inspur NF5486M5 Bedienungsanleitung

Inspur

Inspur NX5760M3 Bedienungsanleitung

Inspur

Inspur NF3120M5 Bedienungsanleitung

Inspur

Inspur i48M6 Bedienungsanleitung

Inspur

Inspur I48M6 Bedienungsanleitung

Inspur

Inspur NF5486M5 Bedienungsanleitung

Inspur

Inspur SA5112M4 Bedienungsanleitung

Inspur

Inspur ON5263M5 Bedienungsanleitung

Inspur

Inspur NF5266M5 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NF3180A6 Bedienungsanleitung

Inspur

Inspur OS Bedienungsanleitung

Inspur

Inspur NF8480M5 Bedienungsanleitung

Inspur

Inspur NF8480M5 Bedienungsanleitung

Inspur

Inspur NF5288M5 Bedienungsanleitung

Inspur

Inspur NF5266M6 Bedienungsanleitung

Inspur

Inspur NF5180M5 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung