Instone EASIER Bedienungsanleitung
www.instone3d.com
Copyright@iNSTONE 3D
User Manual
for Mini 3D Printer
www.instone3d.com
1
Content
Content............................................................................................................................................... 1
Technical Parameters........................................................................................................................2
Packing List........................................................................................................................................3
Installation......................................................................................................................................... 4
Instructions........................................................................................................................................ 5
I. Installation and Operating Guide of Slicing............................................................................7
II. Use of Slicing Software:.......................................................................................................10
1. Understand and Know Well About Software Interface:............................................... 10
2. Machine Settings:..........................................................................................................11
3. Load Model File:...........................................................................................................12
4. Process and Edit Model Files:.......................................................................................12
5. Basic Parameter Setting of Slicing:.............................................................................. 14
6. Senior Parameter Setting of Slicing:.............................................................................15
7. Additional Parameter Setting of Slicing:...................................................................... 16
8. Browse slicing file:....................................................................................................... 18
9. Export of slicing file:.................................................................................................... 18
Online Printing and Updating Firmware..................................................................................... 20
I. Online Printing:......................................................................................................................20
II. Update Firmware:.................................................................................................................20
Tips....................................................................................................................................................21
Service support................................................................................................................................ 22
www.instone3d.com
2
Technical Parameters
Name
Mini 3D Printer
Model
EASIER
Consumable
PLA
Printer size
195*210*275mm
Build volume
110*110*125mm
Printing accuracy
0.1mm(Max)
Printing principle
FDM
Printing temperature
210℃
X, Y, Z axis position accuracy
0.1mm
N.W.
2.4kg
G.W.
4kg
www.instone3d.com
3
Packing List
MINI 3D Printer *1
Power Adapter *1
Power Cable *1
Printing plate *1
TF card *1
Card Reader *1
Glue Stick *1
PLA Filament (280g) *1
Note：Once you received the parcel, please check all the parts; if anything missed,
www.instone3d.com
4
Installation
I. Remove the protecting clip on the plain shaft
II. Install the Feed Pipe
1. Press down the feeding coupling aside the radiator, then insert the white feed pipe
2. Insert the other end of the feed pipe into the socket of the remote extruder
III. Place the printing plate
IV. Feed
1. Unpack the PLA filament from the package, and find out the end of it
2. Bend the head material straightly, and trim the end of the material with scissor
3. Press the spring of the extruder by hands, then insert the filament from the hole on
the bottom of the extruder to the other end of the Feed Pipe (until you can’t insert
anymore). Then hang the filament tray on the hook on side of the printer (Note:
Arrange the filament neatly and DO NOT in a mess).
V. Inserting the TF Card
VI. Plug in and Power on
www.instone3d.com
5
Instructions
Ⅰ.Printing
1. The LCD screen will display the home page after starting up
2. Press the control knob to enter into the main menu; rotate the knob to select the
option “Print from SD card”, and press the knob to enter into the submenu
3. Rotate the knob, and select the option “print file”; press the knob to enter into the
submenu
4. Rotate the knob, select the file to be printed, then press the knob to begin printing
II. Taking down the finished printing models
Take down the printing plate after printing finished, then take down the finished
printing model by a slight bending. After that, clean the surface of the printing plate
(washable).
III.Pause printing
1. During the printing process, press the control knob, and the control menu pops up
on the display screen;
2. Rotate the knob, select the option “pause print”, and press the knob to pause
printing.
IV.Continue printing
☆This function is only applicable to continue printing after pausing in
condition of continuous power on
1. Press the control knob, and the operation menu pops up on the display screen;
2. Rotate the knob, select the option “continue print”, and press the knob to continue
printing.
V. Stop print
☆It is not available to continue printing after stopping printing, so please BE
CAUTIOUS when using this function
1. During the printing process, press the control knob, and the control menu pops up
on the display screen;
2. Rotate the knob, select the option “stop print”, and press the knob to stop printing.
Note: It’s IMPOSSIBLE to continue printing after “stop print”.
VI. Retract/reload the filament
This printer has been equipped with the function of automatic retract of
filament, which can be utilized in condition that the consumable is to be used up
or it is necessary to change to different colors
www.instone3d.com
6
1. At the home page, press the control knob, then the main menu pops up on the
display screen
2. Rotate the knob, select the option “Auto-stripper”, and press the knob to enter into
the operation
3. “Processing...” will show on the interface, and please wait patiently
4. When the automatic retract of material ends up, the display screen will return to
the home page, and the printing head’s temperature will fall, then the operation is
finished
Note
I. Clogs & Clear the nozzle
In normal conditions, there’s no need to worry about this issue as high quality
printing filaments are selected for this printer. If you select other consumables,
the nozzle may be blocked due to impurities in the material or other reasons, in
which condition the following steps may help you.
1. Press the control knob at the home page, press the control knob, and the main
menu pops up on the display screen;
2. Rotate the knob, select the option “heating print head”, and press the knob to enter
into the operation;
3. “Processing” appears on the interface; at this time, the printer is heating the nozzle,
and please wait patiently;
4. When the heating is finished, and the display screen returns back to the home page,
it shows that the temperature of the nozzle is 230℃;
5. Insert hard the filament into the nozzle to clear, until you can feed smoothly.
6. Power off for cooling down after clearing
II. Adjust the height of the nozzle
Too high or too low position of the nozzle will influence the printing (too high, the
printing material cannot stick on the bottom plate; too low, the nozzle will pin the
bottom plate, and the filament cannot be extruded). Adjust the positioning knob
properly as per the following figure, to adjust the distance between the nozzle and the
bottom plate:
www.instone3d.com
7
I. Installation and Operating Guide of Slicing
1. Double click the
file
in TF card to enter
software
installation
interface. User can
select installation
catalog in the red
frame, then single
click [Next]
2.Installation
option, Click
[Install] for
installation.
www.instone3d.com
8
3. Installation is
processing.
4. Single click
[Next] to
install drive
www.instone3d.com
9
5.After
installing drive,
single click
[Finish]
6. Single click
[Next] to
complete
installation.
Inhaltsverzeichnis
Andere Instone 3D-Drucker Handbücher
