Integra DLV-100 Bedienungsanleitung

Digital Light Processing Projector

DLV-100

Instruction Manual

IMPORTANT INFORMATION

Precautions

Please read this manual carefully before using your

Integra Projector DLV-100 and keep the manual handy

for future reference.

Your serial number is located on the bottom of your

DLV-100. Record it here:

CAUTION

To turn off main power, be sure to remove the

plug from power outlet.

The power outlet socket should be installed

as near to the equipment as possible, and

should be easily accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE

CABINET.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SER-

VICE PERSONNEL.

This symbol warns the user that uninsulated

voltage within the unit may be sufficient to

cause electrical shock. Therefore, it is dan-

gerous to make any kind of contact with any

part inside of the unit.

This symbol alerts the user that important in-

formation concerning the operation and main-

tenance of this unit has been provided. The

information should be read carefully to avoid

problems.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN

EXTENSION CORD OR IN AN OUTLET UNLESS ALL

THREE PRONGS CAN BE FULLY INSERTED.

DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLT-

AGE COMPONENTS INSIDE. ALL SERVICING MUST BE

DONE BY QUALIFIED SERVICE PERSONNEL.

DOC Compliance Notice

This Class B digital apparatus meets all requirements of

the Canadian Interference-Causing Equipment Regula-

tions.

RF Interference

WARNING

The Federal Communications Commission does not

allow any modifications or changes to the unit EXCEPT

those specified by Integra Technologies in this manual.

Failure to comply with this government regulation could

void your right to operate this equipment.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful in-

terference in a residential installation. This equipment

generates, uses, and can radiate radio frequency en-

ergy and, if not installed and used in accordance with

the instructions, may cause harmful interference to

radio communications. However, there is no guaran-

tee that interference will not occur in a particular in-

stallation. If this equipment does cause harmful inter-

ference to radio or television reception, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV tech-

nician for help.

• IBM is a registered trademark of International Business Machines

Corporation.

• Macintosh and PowerBook are registered trademarks of Apple

Computer, Inc.

• Other product and company names mentioned in this instruction

manual may be the trademarks of their respective holders.

Important Safeguards

These safety instructions are to ensure the long life of

your projector and to prevent fire and shock. Please read

them carefully and heed all warnings.

Installation

1. For best results, use your projector in a darkened room.

2. Place the projector on a flat, level surface in a dry area away

from dust and moisture.

3. Do not place your projector in direct sunlight, near heaters

or heat radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm in-

ternal components.

5. Handle your projector carefully. Dropping or jarring can dam-

age internal components.

6. Do not place heavy objects on top of the projector.

If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

b. The projector must be installed by qualified technicians in order

to ensure proper operation and reduce the risk of bodily injury.

c. In addition, the ceiling must be strong enough to support the

projector and the installation must be in accordance with any

local building codes.

d. Please consult your dealer for more information.

Power Supply

1. The projector is designed to operate on a power supply of

100-120 or 200-240 V 50/60 Hz AC. Ensure that your power

supply fits this requirement before attempting to use your

projector.

2. Handle the power cable carefully and avoid excessive bend-

ing. A damaged cord can cause electric shock or fire.

3. If the projector is not to be used for an extended period of

time, disconnect the plug from the power outlet.

CAUTION

Do not unplug the power cable from the wall outlet under any

one of the following circumstances. Doing so can cause damage

to the projector:

* While the Hour Glass icon appears.

* While the message "Please wait a moment." appears. This mes-

sage will be displayed after the projector is turned off.

* Immediately after the power cable is plugged into the wall

outlet (the POWER indicator has not changed to a steady or-

ange glow).

* Immediately after the cooling fan stops working (The cooling

fan continues to work for 90 seconds after the projector is

turned off with the POWER button).

* While the POWER and the STATUS indicators are alternately

flashing.

Cleaning

1. Unplug the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily

soiled, use a mild detergent. Never use strong detergents

or solvents such as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful

not to scratch or mar the lens.

Lamp Replacement

•To replace the lamp, follow all instructions provided on page

44.

•Be sure to replace the lamp when the message "The lamp

has reached the end of its usable life. Please replace

the lamp.!!" appears. If you continue to use the lamp after

the lamp has reached the end of its usable life, the lamp

bulb may shatter, and pieces of glass may be scattered in

the lamp case. Do not touch them as the pieces of glass

may cause injury. If this happens, contact your Integra dealer

for lamp replacement.

•Allow a minimum of 90 seconds to elapse after turning off

the projector. Then disconnect the power cable and allow 60

minutes to cool the projector before replacing the lamp.

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are

unobstructed to prevent the build-up of heat inside your pro-

jector. Allow at least 3 inches (10 cm) of space between

your projector and a wall.

2. Prevent foreign objects such as paper clips and bits of pa-

per from falling into your projector. Do not attempt to re-

trieve any objects that might fall into your projector. Do not

insert any metal objects such as a wire or screwdriver into

your projector. If something should fall into your projector,

disconnect it immediately and have the object removed by a

qualified Integra service personnel.

3. Do not place any liquids on top of your projector.

•Do not look into the lens while the projector is on. Serious

damage to your eyes could result.

•Keep any items such as magnifying glass out of the light

path of the projector. The light being projected from the lens

is extensive, therefore any kind of abnormal objects that

can redirect light coming out of the lens, can cause unpre-

dictable outcome such as fire or injury to the eyes.

•Do not cover the lens with the supplied lens cap or equiva-

lent while the projector is on. Doing so can lead to melting of

the cap and possibly burning your hands due to the heat

emitted from the light output.

TABLE OF CONTENTS

1. INTRODUCTION

Introduction to the Projector DLV-100 ............................. 6

Getting Started ............................................................... 6

What’s in the Box............................................................ 7

Getting to Know Your Projector DLV-100 ........................ 8

Front / Side Features ................................................. 8

Attaching the lens cap ................................................ 8

Rear / Side Features .................................................. 9

Top Features ............................................................ 10

Terminal Panel Features ........................................... 11

Remote Control Features ......................................... 12

Remote Control Battery Installation ..................... 13

Operating Range ................................................. 13

Remote Control Precautions ............................... 13

2. INSTALLATION

Setting Up Your Projector ............................................. 14

Selecting a Location ..................................................... 14

Screen and Projection Distance ................................... 14

Distance Chart .............................................................. 15

Reflecting the Image ..................................................... 15

Wiring Diagram ............................................................. 16

Connecting Your PC ................................................. 17

Connecting Your Macintosh Computer .................... 18

Connecting Your DVD Player ................................... 19

Connecting Your VCR or Laser Disc Player ............. 20

About Startup screen (Menu Language Select screen) ..........

3. OPERATION

Connecting the Power Cable and Turn on the Projector ..............

Basic Operation ............................................................ 25

Using the Menus ........................................................... 27

Menu Tree .................................................................... 29

Menu Elements ............................................................. 30

Menu Descriptions & Functions .................................... 31

Source Select ............................................................... 31

RGB/Video/S-Video/PC Card Viewer

Picture .......................................................................... 31

Brightness/Contrast/Color/Hue/Sharpness

Volume .......................................................................... 31

Image Options .............................................................. 32

Keystone .................................................................. 32

Lamp Mode .............................................................. 32

Aspect Ratio ............................................................. 32

Noise Reduction ....................................................... 33

Position/Clock .......................................................... 33

Resolution ................................................................ 33

Video Filter ............................................................... 33

Factory Default ......................................................... 33

Color Management ....................................................... 34

Gamma Correction ................................................... 34

Color Matrix .............................................................. 34

White Balance .......................................................... 34

Projector Options .......................................................... 34

Menu ........................................................................ 34

Menu Mode.......................................................... 35

Advanced Menu, Basic/Custom Menu ............. 35

Language ............................................................ 35

Projector Pointer .................................................. 35

Menu Display Time .............................................. 35

Source Display .................................................... 35

Direct Button (Volume Bar) .................................. 35

Setup ........................................................................ 35

Orientation ........................................................... 35

Cinema position ................................................... 35

Background ......................................................... 35

Mouse .................................................................. 36

Button/Sensitivity.............................................. 36

PC Card Viewer Options ..................................... 36

Capture Options .................................................. 36

Signal Select........................................................ 36

Auto Adjust (RGB only)........................................ 36

Auto Start............................................................. 37

Power Management ............................................ 37

Power Off Confirmation ....................................... 37

Keystone Save .................................................... 37

White Segment .................................................... 37

Clear Lamp Hour Meter ....................................... 37

Communication Speed ........................................ 37

Default Source Select .......................................... 37

Control Panel Key Lock ....................................... 37

Tools ............................................................................. 38

Capture .................................................................... 38

PC Card Files ........................................................... 38

Changing Background Logo .................................... 38

Chalk Board ............................................................. 39

Information .................................................................... 39

Using the PC Card Viewer Function ............................. 40

Features ................................................................... 40

Inserting and Ejecting a CompactFlash™Card ....... 40

Operating the PC Card Viewer Function

from the Projector (playback) ............................... 41

Capturing Images Displayed on the Projector ......... 42

Viewing Digital Images ............................................. 42

Terminology .............................................................. 43

4. MAINTENANCE

Replacing the Lamp ...................................................... 44

5. TROUBLESHOOTING

Status Light Messages ................................................. 45

Common Problems & Solutions .................................... 45

When using the PC Card Viewer function .................... 46

6. SPECIFICATIONS

Optical/Electrical/Mechanical ........................................ 47

Cabinet Dimensions ..................................................... 48

D-Sub Pin Assignments ................................................ 49

Timing Chart ................................................................. 50

PC Control Codes ......................................................... 51

Cable Connection ......................................................... 51

CompactFlash is a trademark of San Disk Corporation.

1. INTRODUCTION

Introduction to the Projector DLV-100

This section introduces you to your new Projector and describes the

features and controls.

Congratulations on Your Purchase of The Projector DLV-100

The DLV-100 is one of the very best projectors available today. The

DLV-100 enables you to project precise images up to 200 inches across

(measured diagonally) from your PC or Macintosh computer (desk-

top or notebook), VCR, DVD player, document camera, a laser disc

player or PC Card Viewer.

You can use the projector on a tabletop or cart, you can use the pro-

jector to project images from behind the screen, and the projector can

be permanently mounted on a ceiling*1. The remote control can be

used wirelessly.

Features you’ll enjoy:

•Simple set up and operation.

•A high-performance 135 watt NSH lamp.

•The supplied wireless remote control that operates the projector

from the front or rear.

•The image can be projected between 30 and 200 inches (mea-

sured diagonally).

•Keystone correction allows you to correct trapezoidal distortion

so that the image is square.

•You can choose between video modes depending on your source:

"normal" for a typical picture, "natural" for true color reproduc-

tion.

•The built-in PC Card Viewer allows you to start your presenta-

tion even when a PC is not available at the site.

•The "Capture" enables you to capture the current projected im-

age.

•An image can be projected from in front or behind a screen, and

the projector can even be installed on the ceiling.

•An exclusive Advanced AccuBlend intelligent pixel blending

technology - an extremely accurate image compression technol-

ogy - offers a crisp image with UXGA (16001200) resolu-

tion*2.

•Supports most IBM VGA, SVGA, XGA, SXGA/UXGA (with

Advanced AccuBlend)*2, Macintosh, component signal (YCbCr

/YPbPr) or any other RGB signals within a horizontal frequency

range of 15 to 100 kHz and a vertical frequency range of 50 to

120 Hz. This includes NTSC, PAL, PAL-N, PAL-M, PAL60,

SECAM and NTSC4.43 standard video signals.

NOTE:

Composite video standards are as follows:

NTSC: U.S. TV standard for video in U.S. and Canada.

PAL: TV standard used in Western Europe.

PAL-N: TV standard used in Argentine, Paraguay and Uruguay.

PAL-M: TV standard used in Brazil.

PAL60: TV standard used for NTSC playback on PAL TVs.

SECAM: TV standard used in France and Eastern Europe.

NTSC4.43: TV standard used in Middle East countries.

•The supplied remote control can be used without a cable.

•You can control the projector with a PC using the PC Control

port.

•USB terminal allows USB mouse operation*3.

•The contemporary cabinet design is light, compact, easy to carry,

and complements any office, boardroom or auditorium.

*1 Do not attempt to mount the projector on a ceiling yourself.

The projector must be installed by qualified technicians in order

to ensure proper operation and reduce the risk of bodily injury.

In addition, the ceiling must be strong enough to support the pro-

jector and the installation must be in accordance with any local

building codes. Please consult your dealer for more information.

*2 A UXGA (16001200) and SXGA image (12801024) are

displayed.

*3 The USB terminal meets the USB1.1 specification and accepts a

USB mouse only.

Getting Started

The fastest way to get started is to take your time and do everything

right the first time. Take a few minutes now to review the instruction

manual. This may save you time later on. At the beginning of each

section of the manual you’ll find an overview. If the section doesn’t

apply, you can skip it.

What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer.

Please save the original box and packing materials if you ever need to ship your Projector DLV-100.

String and rivet

Remote control

Power cable

RGB signal cable

Registration

Card

Quick

Connect

Guide

Instruction

Manual

INPUT

Soft carrying case

SELECT

AUTO

ADJUST

PC CARD ACCESS

STATUS

POWER

ON/

STAND BY SOURCE

Lens cap

Projector

Batteries

SELECT

AUTO

ADJUST

PC CARD ACCESS

STATUS

POWER

ON/

STAND BY SOURCE

Controls

Adjustable Tilt Foot Button

Remote Sensor

Ventilation (inlet)

Adjustable Tilt Foot

Lens Cap

Zoom Ring

Lens

Focus Ring

Getting to Know Your Projector DLV-100

Attaching the lens cap to the lens hood with the supplied string and rivet

Front/ Side Features

1. Thread the string through the hole on the lens cap and then tie a knot in the string.

2. Use the rivet to attach the string to the bottom of the lens hood.

Attaching the lens cap

○○○○○○○○○○○○○○○○○○○○○○○○

AC IN

PC CARD

USB

VIDEO

S-VIDEO

RGB

AUDIO

PC CONTROL

SELECT

AUTO

ADJUST

PC CARD ACCESS

STATUS

POWER

ON/

STAND BY SOURCE

AC Input

Slot for Kensington

MicroSaver

Security System

Monaural Speaker (1W)

Remote Sensor

Heated air is exhausted from here

Spacer (black rubber)

Ventilation (outlet)

Terminals and PC card

Ventilation (inlet)

Rear Foot

Rear/ Side Features

Rotate to fine-adjust horizontally

position

Bottom

Lamp cover

Lamp cover screw

Ventilation (inlet)

Rear Foot

Spacer (black rubber)

NOTE: The projector has an internal temperature sen-

sor. The sensor controls the speed of the fan to keep

constant temperature in the inside.

When the internal temperature rises, the built-in fan au-

tomatically runs at a high speed (high-speed mode).

During this time, the sound of exhaust may be heard.

This is not a malfunction.

(not adjustable)

Rear Foot

To fine-adjust the height of the rear

foot, remove the spacer and rotate

the rear foot to the desired height.

Top Features

1. Power Button (ON / STAND BY)

Use this button to turn the power on and off when the power is

supplied and the projector is in standby mode.

2. Status Indicator

When this is lit red continually, it's warning you that the projection

lamp has exceeded 1500 hours (1000 hours in High-Bright mode)

of service. After this light appears, it is advisable to replace the

projection lamp as soon as possible. (See page 44). In addition the

message "The lamp has reached the end of its usable life. Please

replace the lamp!!." appears continually until the lamp is replaced.

If this light blinks red rapidly, it indicates that the lamp cover is not

attached properly or the projector is overheated.

See the Power/Status Light Messages on page 45 for more details.

3. Power Indicator ( )

When this indicator is green, the projector is on; when the indica-

tor is orange, it is in standby mode.

4. Source Button

Use this button to select a video source such as a PC, VCR, DVD

player or PC Card Viewer (CompactFlash card).

Each time this button is pressed, the input source will change as

follows:

→RGB →Video →S-Video →PC Card Viewer 

If no input signal is present, the input will be skipped.

5. Auto Adjust Button (RGB only)

Use this button to adjust Position-H/V and Pixel Clock/Phase for

an optimal picture. Some signals may not be displayed correctly or

take time to switch between sources.

6. PC Card Access Indicator

Lights while accessing a CompactFlash memory card.

7. Enter Button

Executes your menu selection and activates items selected from

the menu.

8. Cancel Button

Press this button to exit "Menus". Press this button to return the

adjustments to the last condition while you are in the adjustment

or setting menu.

9. Select (▲▼ ) / Volume (+) (–) Buttons

▲▼: Use these buttons to select the menu of the item you wish

to adjust.

When no menus appear, these buttons work as a volume

control.

 : Use these buttons to change the level of a selected menu

item.

A press of the  button executes the selection.

When the menus or the Viewer tool bar is not displayed,

these buttons can be used to select a slide, or to move the

cursor in Folder List or Slide List.

When the magnifying glass is displayed, these ▲▼ 

buttons move the magnifying glass.

10. Menu Button

Displays the menu.

PC CARD

USB

VIDEO

S-VIDEO

RGB

AUDIO

PC CONTROL

SELECT

AUTO

ADJUST

PC CARD ACCESS

STATUS

POWER

ON/

STAND BY SOURCE

Andere Handbücher für DLV-100

Inhaltsverzeichnis

Andere Integra Projektor Handbücher

Integra

Integra DLV-100 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

Epson

Epson PowerLite 810p Bedienungsanleitung