8. Programmable Output
A PGM is a programmable output that can be activated and
deactivated based on specific events or functions within the Protege
System. The primary function of the Standard 16 PGM Output
Expander is to activate any one of the 16 onboard PGM Outputs.
PGM Function
PXXXX:01 P1 Open Collector PGM Output
PXXXX:02 P2 Open Collector PGM Output
PXXXX:03 P3 Open Collector PGM Output
PXXXX:04 P4 Open Collector PGM Output
PXXXX:05 P5 Open Collector PGM Output
PXXXX:06 P6 Open Collector PGM Output
PXXXX:07 P7 Open Collector PGM Output
PXXXX:08 P8 Open Collector PGM Output
PXXXX:09 P9 Open Collector PGM Output
PXXXX:10 P10 Open Collector PGM Output
PXXXX:11 P11 Open Collector PGM Output
PXXXX:12 P12 Open Collector PGM Output
PXXXX:13 P13 Open Collector PGM Output
PXXXX:14 P14 Open Collector PGM Output
PXXXX:15 P15 Open Collector PGM Output
PXXXX:16 P16 Open Collector PGM Output
9. Error Messages
When the Standard 16 PGM Output Expander is powered up and
starts communicating with the controller it is possible that the
Standard 16 PGM Output Expander can be denied access to the
module network. This is a normal part of the Protege System.
In normal operation the status indicator will flash rapidly while it is
attempting to contact the controller. When it is online it will turn flash
at one second intervals. When an error occurs the status indicator will
FLASH with the error code number. The error code number is shown
with a 250ms ON and OFF period (duty cycle) with a delay of 1.5
seconds between each display cycle.
Flash Error Description
1Internal Error
An internal error has occurred on the Standard 16 PGM
Output Expander. Please contact your distributor.
2Version Error
The version of the Standard 16 PGM Output Expander is
not correct for the system controller. The firmware must be
updated. Please contact your distributor.
3Address Too High
The address of the Standard 16 PGM Output Expander
that is programmed is beyond the maximum number of
Standard 16 PGM Output Expander that are allowed to
connect to the system controller. You may also be able to
adjust the controller profile to increase the Standard 16
PGM Output Expander module capacity.
4Duplicate Device Address
The address of the Standard 16 PGM Output Expander is
already programmed in to the address location.
5Security Violation
The system controller has security enabled and no devices
can be added to the system.
6Invalid Serial Number
The Standard 16 PGM Output Expander has an invalid
serial number programmed and can not be registered on
the system. Return the Standard 16 PGM Output Expander
to your distributor.
10. Technical Specifications
Operating Voltage 11.5VDC to 14.25VDC
Operating Current 47mA (83mA, Max)
Communication (Serial) Communication Interface Port
Zone Inputs 16x Standard Zones Dual EOL Resistor
(1K+1K) or No Resistor per Zone
PGM Outputs 1x 50mA (Max) Open Collector Output for
General Functions
Operating Temperature 5˚to 55˚C (41˚to 131˚F)
Storage Temperature -10˚to 85˚C (14˚to 185˚F)
Humidity 0% to 85% (Non Condensing)
Dimensions (H x W x D) 93 x 130 x 12mm (3.66 x 5.11 x 0.47”)
Weight 165g (5.82oz)
The size of conductor used for the supply of power to the Protege
Intelligent 5 Amp Power Supply should be adequate in size to prevent
voltage drop at the terminals of no more than 5% of the rated supply
voltage.
Specifications are subject to change without notice, please visit
www.incontrol.co.nz for updated information.
Integrated Control Technology Limited
11 Canaveral Drive, Albany, North Shore City 0632, Auckland, New Zealand
P.O. Box 302-340, North Harbour, Auckland, New Zealand
Phone: +64 (9) 476 7124
Fax: +64 (9) 476 7128
www.incontrol.co.nz
Designers and manufacturers of integrated electronic access control, security and building
automation products.
Designed and manufactured by Integrated Control Technology Limited.
© Copyright Integrated Control Technology Limited 2003-2011. All rights reserved.
227-4095-002
