Intel SYS7180VE Bedienungsanleitung

SYS7180VE

PICMG Single Board Computer

For socket 478 CPU With VGA/ LAN

(Pentium 4™&Celeron™&Intel® Celeron®DTM CPU)

User’s Manual

manufacturer reserves the right to make improvements to the products

described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmitted in

any form or by any means without the prior written permission of the original

manufacturer. Information provided in this manual is intended to be accurate

and reliable. However, the original manufacturer assumes no responsibility for

its use, nor for any infringements upon the rights of third parties that may result

from such use.

Acknowledgments

IBM/AT and PS/2 are trademarks of International Business Machines

Corporation.

Award is a registered trademark of Award Software International, Inc.

Intel®, Celeron™, Pentium 4™ and Pentium 4™ are registered trademarks of

Intel Corporation.

Microsoft Windows is a registered trademark of Microsoft Corporation.

All Other product names or trademarks are properties of their respective

owners.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no

event will the warrantor be liable for any incidental or consequential damages

due to such defect or consequences that arise from inexperienced usage, misuse,

or malfunction of this device.

Additional Information and Assistance

1. The manufacturer recommends using a grounded plug to ensure proper

motherboard operation. Care should be used in proper conjunction

with a grounded power receptacle to avoid possible electrical shock.

All integrated circuits on this motherboard are sensitive to static

electricity. To avoid damaging components from electrostatic

discharge, please do not remove the board from the anti-static packing

before discharging any static electricity to your body, by wearing a

wrist-grounding strap. The manufacturer is not responsible for any

damage to the motherboard due to improper operation.

2. Visit the Grantech web site at www.grantech.com.tw where you can

find the latest information about the product.

3. Contact your distributor, sales representative, or Grantech's customer

service center for technical support if you need additional assistance.

Please have the following information ready before you call:

•Product name and serial number

•Description of your peripheral attachments

•Description of your software (operating system, version, application, etc.)

•A complete description of the problem

•The exact wording of any error messages

Table of Contents

SYS7180VE User’s Manual i

Table of Contents

CHAPTER 1 INTRODUCTION ...............................................1

1.1 SPECIFICATION....................................................................1

1.2 CHECK LIST ........................................................................1

1.3 DESCRIPTION ......................................................................2

1.4 POWER REQUIREMENTS ......................................................2

1.5 CONNECTOR & JUMPER LOCATION .........................................4

1.6 BLOCK DIAGRAM....................................................................5

CHAPTER 2 HARDWARE INSTALLATIONS ......................6

2.1 INSTALLATION PROCEDURE .................................................6

2.2 CPU INSTALLATION:...........................................................7

2.3 MAIN MEMORY INSTALLATION: DIMM1/2.........................8

2.4 JUMPER SETTINGS:............................................................10

2.5 CONNECTORS SETTING: ....................................................12

2.5.1 FRONT PANEL CONNECTOR: J1 .........................................13

2.5.2 USB CONNECTOR: USB1-2 USB3-4 ...............................14

2.5.3 PARALLEL PORT CONNECTOR: LPT ..................................15

2.5.4 SERIAL PORT CONNECTOR:COM1/COM2........................16

2.5.5 IDE PORT CONNECTOR: IDE1/ IDE2................................16

2.5.6 FLOPPY DISK CONNECTOR: FLOPPY...............................17

2.5.7 ADAPTER CONNECTOR FOR 10/100 LAN: LAN1..............18

2.5.8 ADAPTER CONNECTOR FOR GIGALAN: LAN2 ...............19

2.5.9 EXTERNAL KEYBOARD/MOUSE CONNECTOR:...................20

Table of Contents

ii SYS7180VE User’s Manual

2.5.10 VGA CONNECTOR:.......................................................21

2.5.11 KEYBOARD / MOUSE CONNECTOR:...............................21

2.5.12 CPU FAN CONNECTOR:...............................................21

2.5.13 ACPI CONNECTOR: J2..................................................22

CHAPTER 3 BIOS SETUP......................................................24

3.1 INTRODUCTION .................................................................24

3.2 MAIN MENU .....................................................................26

3.3 STANDARD CMOS SETUP.................................................28

3.4 ADVANCED BIOS FEATURES SETUP..................................30

3.5 ADVANCED CHIPSET FEATURES SETUP .............................34

3.6 INTEGRATED PERIPHERALS ...............................................38

3.7 POWER MANAGEMENT SETUP...........................................43

3.8 PNP/PCI CONFIGURATION SETUP .....................................49

3.9 PC HEALTH STATUS ..........................................................51

3.10 DEFAULTS MENU ..............................................................51

3.11 SUPERVISOR/USER PASSWORD SETTING ...........................52

3.12 EXIT SELECTING ...............................................................52

3.13 POST MESSAGES .............................................................53

3.14 POST BEEP ......................................................................53

3.15 ERROR MESSAGES ............................................................53

Appendix…………………………………………………………..59

CHAPTER 1 – Introduction

SYS7180VE User’s Manual 1

Chapter 1 Introduction

1.1 Specification

Processor Support Intel® PentiumTM 4 CPU up to 3.06 GHz

Support Intel® CeleronTM CPU up to 2.60 GHz

Support Intel® Celeron®DTM CPU up to 2.80 GHz (Prescott core)

Chipset Intel®82845GV chipset supports 400/533MHz FSB

Memory Two 184-pin DDR DIMMs socket, up to 2GB of 266/333MHz

DDR SDRAM

BIOS Award4MbitPnPflashBIOS

VGA Integrated in 845GV, AGP4X

Sharememoryupto64MBwithsystemmain-memory

LAN LAN1: Intel® 82562ET Ethernet controller, supports 10/100M

Base-T

LAN2: (optional)Intel®82540EM Ethernet controller, supports

10/100/1000 Base-T

Wake On LAN support

USB Four USB ports, Hi-speed USB 2.0

Super I/O Mini-DIN: 1x PS/2 keyboard/mouse connector

RJ-45: 10/100/1000Mb Ethernet connector

Female DB-15: VGA connector

Box-header: 2* Serial port (2x5Pin);

1*FDD (2x17Pin); 2* EIDE (2x20Pin);

Pin-header: 1*Parallel port (2x13Pin)

Watchdog System reset or non- maskable interrupt software programmable

time I interval and jumper selectable (64-level)

Operating temperature 0°C ~60°C

Relative humidity 10%~90% non-condensing at temperature of 40BC or

104BF

1.2 Check List

Please check that your package is complete and contains the items below. If you

discover damaged or missing items, please contact your dealer.

 SYS7180VE CPU card

 Utility CD for SYS7180VE

 Installation Guide

 IDE cable *2

 FDD cable *1

CHAPTER 1 – Introduction

2 SYS7180VE User’s Manual

 PS/2 1 to 2 adapter *1

 Com extension cables with bracket *1

 Com, Printer extension cables with bracket *1

 +12V power cable *1

 USB cable *1（Special for SYS7180VE）

 Jumper Short Pin: 6 pcs

1.3 Description

The SYS7180VE is a motherboard based on Intel 845GV chipset and is fully

designed for PC environment. It features socket 478 compatible with Intel’s processor.

This card accommodates up to 2GB of DDR memory.

The SYS7180VE comes with on board CPU temperature sensor to protect your

processor from overheating (Winbond W83627HF chipset). Wired for Management

(WFM) 2.0 specification compliance.

The SYS7180VE has a LAN connector that uses Intel ICH4 integrated with Intel

82562ET (AOL & 10/100) controller.

1.4 Power Requirements

Your system requires a clean, steady power source for reliable performance of the

high frequency CPU on the SYS7180VE Industrial CPU card, the quality of the power

supply is even more important. For the best performance makes sure your power supply

provides a range of 4.75 volts minimum to 5.25 volts maximum DC power source.

Power Consumption

For typical configurations, the CPU card is designed to operate with at least a 200W

power supply. A higher-wattage power supply should be used for heavily-loaded

configurations. The power supply must meet the following requirements:

 Rise time for power supply: 2 ms to 20 ms

 Minimum delay for reset to Power Good: 100 ms

 Minimum Power down warning: 1 ms

CHAPTER 1 – Introduction

SYS7180VE User’s Manual 3

 3.3 V output must reach its minimum regulation level within 20ms of the +5V

output reaching its minimum regulation level

The following table lists the power supply’s tolerances for DC voltages:

DC Voltage Acceptable Tolerance

+3.3 V ± 5 %

+5 V ± 5 %

+5 VSB (standby) ± 5 %

-5 V ± 5 %

+12 V ± 5 %

-12 V ± 5 %

CHAPTER 1 – Introduction

4 SYS7180VE User’s Manual

1.5 Connector & Jumper Location

CHAPTER 1 – Introduction

SYS7180VE User’s Manual 5

1.6 Block Diagram

PCI TO ISA

Bridge

W83629D

GIGA LAN

Connector

ICH4

Processor

PWM

PICMG PCI/ISA SLOT

VGA CRT

CONNECTOR

SOCKET 478

P4 PROCESSOR

AC'97

CODEC

CTRL

DATA

IDE Secondary

GMCH

COM1

Floppy COM2

AC'97 LINK

DDR 266 Mhz

RAID Secondary IDE

IDE Primary

Modules

FirmWare Hub

LAN 10/100

RJ45-Connector

W83627HF

Audio

Connector

DDR266

RS232 /

422 /

485

DATA

PHY

82562EM

UDMA66/100

USB I/F

CTRL

Keyboard

LPC

SUPER-I/O

BROOKDALE-G

RAID IDE

CONTROLLER

PDC20265R RAID Primary IDE

CLOCK

ICS950220

AGTL+ BUS

ADDR

Mouse

ADDR

USB 2.0

PORT 1-6 GIGA LAN

CONTROLLER

82540

LPC INTERFACE

Parallel

PCI CNTRL + PCI ADDR/DATA

RS232

FCBGA760

IrDA

CHAPTER 2 –Hardware Installations

6 SYS7180VE User’s Manual

Chapter 2 Hardware Installations

This chapter provides information on how to use the jumpers and connectors on

the SYS7180VE in order to set up a workable system.

2.1 Installation procedure

2.1.1 Insert the system BIOS (if not already installed) genteelly. Pay attention to

the position of pin 1 of BIOS socket.

2.1.2 Install the processor with correct orientation.

2.1.3 Insert the DRAM module with correct orientation.

2.1.4 Mount the Fan on the top of the processor and connect it to FAN connector.

2.1.5 Insert all external cables except for flat panel. (Hard disk, floppy, keyboard,

Mouse, LAN, etc.)

2.1.6 Prepare a CRT monitor for CMOS setup.

2.1.7 Confirm the power supply is off.

2.1.8 Turn on the power.

Note: The CMOS memory may be in an undefined state at power-on after a period of no

battery backup.

CHAPTER 2 –Hardware Installations

SYS7180VE User’s Manual 7

2.2 CPU Installation:

The SYS7180VE Industrial CPU Card supports a single Intel®P4 CeleronTM or

Celeron DTM processor and Pentium 4TM processor. The processor’s VID pins

automatically program the voltage regulator on the CPU card to the required processor

voltage. The host bus speed is automatically selected. The processor connects to the CPU

card through the 478-pins socket.

The CPU card supports the processors listed in table below:

P4 CeleronTM processor

Host Bus frequency Cache size

400MHz 128KB

Pentium 4TM processor

Host Bus frequency Cache size

400MHz / 533MHz 512KB

Celeron DTM processor

Host Bus frequency Cache size

533MHz 256KB or 1M

The socket-478 comes with a lever to secure the processor. Make sure the notch on

the corner of the CPU corresponds with the notch on the inside of the socket.

After you have installed the processor into the socket 478, check if the

configuration setup for the CPU type and speed are correct. The CPU should always have a

Heat Sink and a cooling fan attached to prevent overheating.

Note: Ensure that the CPU heat sink and the CPU top surface are in total contact to avoid

CPU overheating problem that would cause your system to hang or be unstable.

CHAPTER 2 –Hardware Installations

8 SYS7180VE User’s Manual

2.3 Main Memory Installation: DIMM1/2

The SYS7180VE Industrial CPU Card supports two single-side or double-sided

DDR266/333 unregistered, DIMM 184-pin sockets for a maximum total memory of 1GB.

Using the non-ECC DDR SDRAM DIMMS.

The CPU card supports the following memory features:

• 184-pin DIMMs with gold-plated contacts

• 266MHz and 333MHz non-ECC DDR SDRAM

• Un-buffered single or double-sided DIMMs in the following sizes:

SDRAM

SYNCHRONOUS DRAM (SDRAM) improves memory performance through

memory access that is synchronous with the memory clock. Burst transfer rates at x-1-1-1

timing can be achieved using SDRAM, while asynchronous memory subsystems are

typically limited at x-2-2-2 transfer rates.

The CPU card supports single or double-sided DIMMs in the following sizes:

DIMM size Non-ECC configuration

16MB 2Mbit x 64

32MB 4Mbit x 64

64MB 8Mbit x 64

128MB 16Mbit x 64

256MB 32Mbit x 64

Note: All memory components and DIMMs used with the SYS7180VE CPU card must

comply with the PC SDRAM Specification. These include: the PC SDRAM Specification

*memory component specific), the PC Unbuffered DIMM Specification, and the PC Serial

Presence Detect Specification.

CHAPTER 2 –Hardware Installations

SYS7180VE User’s Manual 9

Chipset

Intel 82845GV GMCH overview

The features:

 400/533 MHz PSB (100/133MHz bus clock)

 32-bit addressing for access to 2GB of memory space up to 2GB of 266MHz

or 333 MHz DDR SDRAM.

 Supports only for un-buffered non-ECC DIMMs.

 Hub Interface:

- Supports Hub Interface 1.5

- 266MB/s point-to-point Hub Interface to the ICH4.

- 1.5V operation.

 AGP Interface

- Supports a single 1.5VAGP 2.0 compliant device.

 Integrated Graphics

- 3D Setup and Render Engine.

- 2D Graphics.

 Analog Display Support

 Digital Display Channels

CHAPTER 2 –Hardware Installations

10 SYS7180VE User’s Manual

2.4 Jumper Settings:

Jumper Default setting

Jumper setting

FSB FSB setting: auto Short 1-2

JCC Clear CMOS：Normal mode Short 2-3

JAV BIOS write-protect: disabled Open

J4 AT or ATX select: AT Short 1-2

2.4.1 FSB Setting:

Options Setting

400 Short 2-3

533 Open

123

Auto (default) Short 1-2

2.4.2 Clear CMOS Setting: JCC

Options Settings

Normal Short 2-3 (default)

Clear CMOS Short 1-2

JCC

2.4.3 BIOS Write-protect Setting：JAV

Options Settings

Disable Open (default)

Enable Short 1-2

JAV

CHAPTER 2 –Hardware Installations

SYS7180VE User’s Manual 11

2.4.4 AT/ATX Power Setting：J4

Options Settings

AT Short 1-2 (default)

ATX Short 2-3

2.4.5 Watchdog Setting: JWD

Options Setting

IRQ11 Short 1-2

Reset Short 2-3 (default)

123

Disabled Open

CHAPTER 2 –Hardware Installations

12 SYS7180VE User’s Manual

2.5 Connectors Setting:

Connectors Label Connectors Label

Primary IDE Connector IDE1 ACPI Connector J2

Secondary IDE Connector IDE2 VGA Connector VGA

FDD Connector FLOPPY PS/2 Mouse Connector MS

Printer Port Connector LPT PS/2 Keyboard Connector KB

USB 1_2 Connector USB1_2 Keyboard/Mouse

Connector MKB

USB 3_4 Connector USB3_4 CPU Fan Connector CPUFAN

DDR1 184P Connector DIMM1 DDR2 184P Connector DIMM2

COM1 Connector COM1 COM2 Connector COM2

Ethernet 1 RJ-45

Connector

LAN1 Ethernet 2 RJ-45

Connector LAN2

Flat Panel Connector J1 ATX +12V Power

Connector

CHAPTER 2 –Hardware Installations

SYS7180VE User’s Manual 13

2.5.1 Front Panel Connector: J1

This header can be connected to a front panel power switch. The front panel

connector includes headers for these I/O connections:

Power switch

Power LED

This header can be connected to an LED that will light when the computer is

powered on.

Hard drive activity LED

This header can be connected to an LED to provide a visual indicator that data is

being read from or written to an IDE hard drive. For the LED to function properly, the IDE

drive must be connected to the onboard IDE controller.

Speaker

A speaker can be installed on the SYS7180VE as a manufacturing option. The

speaker is enabled by a jumper on pins 2, 4, 6, 8 of the front panel connector. Removing

the jumper can disable the onboard speaker, and an offboard speaker can be connected in

its place. The speaker (onboard or offboard) provides error beep code information during

the POST in the event that the computer cannot use the video interface. The speaker is not

connected to the audio subsystem and does not receive output from the audio subsystem.

19 17 15 13 11 9 7 5 3 1

20 18 16 14 12 10 8 6 4 2

1-3-5: POWER LED 2-4-6-8: SPEAKER 7-9: KEYLOCK

13-14:POWER ON 15-16: GREEN LED 17-18: RESET

19-20: IDE LED

PIN1—POWER LED+ PIN5—POWER LED-

PIN15—GREEN LED+ PIN16—GREEN LED-

PIN19—IDE LED- PIN20—IDE LED+

CHAPTER 2 –Hardware Installations

14 SYS7180VE User’s Manual

2.5.2 USB Connector: USB1-2 USB3-4

Note: USB cable is special designed for SYS7180VE

The Universal Serial Bus (USB) that allows plug and play computer peripherals

such as keyboard, mouse, joystick, scanner, printer, modem/ISDN, CD-ROM and floppy

disk drive to be automatically detected when they are attached physically without having to

install drivers or reboot.

The USB connectors allow any of several USB devices to be attached to the

computer. Typically, the device driver for USB devices is managed by the operating

system. However, because keyboard and mouse support may be needed in the Setup

program before the operating system boots, the BIOS supports USB keyboards and mice.

The CPU card has four USB ports; one USB peripheral can be connected to each

port. For more than four USB devices, an external hub can be connected to either port. The

four USB ports are implemented with stacked back panel connectors. The CPU card fully

supports the universal host controller interface (UHCI) and uses UHCI-compatible

software drivers.

USB features includes:

 Self-identifying peripherals that can be plugged in while the computer is running

 Automatic mapping of function to driver and configuration

 Support for synchronous and asynchronous transfer types over the same set of wires

 Support for up to 127 physical devices

 Guaranteed bandwidth and low latencies appropriate for telephony, audio and other

applications

 Error-handling and fault-recovery mechanisms built into the protocol

Inhaltsverzeichnis

Andere Intel Hauptplatine Handbücher

Intel

Intel SBC83675 Bedienungsanleitung

Intel

Intel D915PLWD Bedienungsanleitung

Intel

Intel G31 EXPRESS CHIPSET SPECIFICAT Bedienungsanleitung

Intel

Intel BLKDP55KG - LG1156 MAX-16 GB DDR3 ATX... Konfigurationshandbuch

Intel

Intel BLKD410PTL Bedienungsanleitung

Intel

Intel Aero Montageanleitung

Intel

Intel BLKD201GLYL Konfigurationshandbuch

Intel

Intel BLKDP965LTCK - Conroe LGA775 1066 800FSB DDR2 Audio Lan SATA ATX 10Pack... Bedienungsanleitung

Intel

Intel G41 Express Chipset Bedienungsanleitung

Intel

Intel D925XBC - Desktop Board Motherboard Bedienungsanleitung

Intel

Intel Desktop Board D915PSY Bedienungsanleitung

Intel

Intel DQ45EK - Desktop Board Executive Series... Bedienungsanleitung

Intel

Intel BLKD945GCPE - LGA775 1066FSB 2DDR2 2GB Audio Video Lan mATX 10Pack... Konfigurationshandbuch

Intel

Intel BLKDG33TLM - G33 Express Socket775 mATX... Bedienungsanleitung

Intel

Intel BLKD915PBLL - LGA775 800FSB 4DDR2 Audio Lan 1394a SATA Raid ATX 4PCI 10Pack... Konfigurationshandbuch

Intel

Intel D845PEBT2 Bedienungsanleitung

Intel

Intel Pentium NR110 Bedienungsanleitung

Intel

Intel i945G2-IQNAR Bedienungsanleitung

Intel

Intel DH55PJ Bedienungsanleitung

Intel

Intel D845GBV Technisches Handbuch

Intel

Intel BOXD915PCML - Desktop Board D915PCML Bedienungsanleitung

Intel

Intel YA810E Konfigurationshandbuch

Intel

Intel DH61BE Bedienungsanleitung

Intel

Intel D945PVS Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung