Intellinet 524582 Bedienungsanleitung

Wireless G

4-Port VPN

router

quick

iNstall

Guide

MODEL 524582

INT-524582-QIG-0309-01

IMPORTANT NOTICE: It has recently been discovered that the

WAN Idle Time Out auto-disconnect function may not work due to

abnormal activities of some network application software, computer

viruses or hacker attacks from the Internet. For example, some

software sends network packets to the Internet in the background,

even when you are not using the Internet. This function also may not

work with some Internet service providers. If you decide to enable

this function, make sure it works properly the rst time, especially

if your ISP charges are based on connection time. Due to the many

uncontrollable issues, we do not guarantee the WAN Idle Time Out

auto-disconnect function will always work: To avoid resulting fees

charged by your ISP, don’t enable this function.

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS

™

Wireless G 4-Port VPN Router, Model 524582.

This quick install guide presents the rudimentary steps required to set up

and operate this device. For more detailed instructions and specications,

refer to the user manual 1) on the CD enclosed with this product; 2) on

the Web site listed below; or 3) in some cases, printed and enclosed

with this product. Contact your INTELLINET NETWORK SOLUTIONS

dealer with comments or questions, or visit www.intellinet-network.com

for information on the latest software and rmware updates, related

products and additional contact information.

NOTE: Some screen images have been modied to t the format of

this quick install guide.

reGulatory statemeNts

FCC Part 15

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to an outlet on a different circuit.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This equipment must be installed and operated in accordance with the

provided instructions, and a minimum of 20 cm spacing must be provided

between a computer-mounted antenna and a person’s body (excluding

extremities of hands, wrists and feet) during wireless modes of operation.

This device complies with Part 15 of FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. Any changes

or modications not expressly approved by the party responsible for

compliance could void the authority to operate equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. To avoid the possibility of exceeding

the FCC radio frequency exposure limits, human proximity to the antenna

shall not be less than 20 cm (8 inches) during normal operation. The

antenna(s) used for this transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of Directive 1999/5/

EC of the European Parliament and the Council of March 9, 1999, on

radio equipment and telecommunications terminal equipment and the

mutual recognition of their conformity (R&TTE). The R&TTE Directive

repeals and replaces Directive 98/13/EEC (Telecommunications Terminal

Equipment and Satellite Earth Station Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those

who install and use it. However, special attention must be paid to the

dangers of electric shock and static electricity when working with electrical

equipment. All FCC and computer manufacturer guidelines must therefore

be followed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and ofce use in

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland,

Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden and the

U.K. The ETSI version of this device is also authorized for use in EFTA

member states Iceland, Liechtenstein, Norway and Switzerland. (EU

countries not intended for use: none.)

iNitial setuP

1. Set up your network as shown in the diagram. NOTE: The four LAN

connections are examples only.

2. Your LAN PC clients need to be set so that an IP address can be

obtained automatically. By default, the router’s DHCP server is enabled

so that this doesn’t require any extra steps here. NOTE: Make sure

the router’s DHCP server is the only DHCP server available on your

LAN. If there is another DHCP on your network, you’ll need to switch

one of the DHCP servers off.

3. Once your PC has obtained an

IP address from your router,

enter the default IP address —

192.168.2.1 (this is the router’s IP

address) — into your PC’s Web browser and press <Enter>.

4. When the login screen

displays, ll in the “User

name” and “Password”

elds, then click “OK”

to log in. NOTE: The

default username is

“admin”; the password

is “1234.” For security

reasons, it’s recommended that you change the password as soon as

possible (see General Setup / System / Password in the user manual).

Once logged in, you can navigate through the Web-based management

user interface by selecting the

options at the top-right. To

access the Quick Setup Wizard,

click “HOME,” then “Quick Setup” (one of the four sub-menu buttons

displayed in the left-hand menu section).

quick setuP

The Quick Setup section is designed to get you using the Wireless G

4-Port VPN Router as quickly as possible. To congure the router as

more than just an Internet access device — taking advantage of the many

features and functions — refer to the user manual on the enclosed CD.

In Quick Setup, you’re only shown how to enter the information needed

to access the Internet. Once you click “Quick Setup Wizard” on the

HOME page, you should see the Time Zone screen below.

Time Zone

Your router will base its time on the settings congured here, which will

affect functions such as log entries and rewall settings.

HOME

General Setup

ToolsStatus

Set Time Zone — Select the time zone of the country or region you’re in.

The router will set its time based on your selection.

Time Server Address — In case the default time server isn’t working, you

can manually assign a time server address in this eld.

Daylight Saving — For the router to account for Daylight Saving changes,

select “Enable Function” and use the drop-down menus to select the

time period you want the function to take effect.

Click “Next” to affect any changes and advance to the next screen.

Broadband Type

Select the type of connection you’ll be using to connect your router’s WAN

port to your Internet service provider. As different ISPs require different

methods of connecting to the Internet, check as to the type of connection

your ISP requires. Click “Back” to return to the previous screen.

Broadband Type: Cable Modem

Select if your ISP will automatically give you an IP address. Some ISPs

require that you provide additional information, such as host name and

MAC address (as shown below).

Host Name — If your ISP requires a host name, enter the host name it

provides; otherwise, leave it blank

MAC Address — Enter the PC’s MAC address originally assigned by your

ISP. As an option, you can click “Clone MAC Address” to replace the

router’s WAN MAC address with the initial MAC address of that PC.

NOTE: You have to be using that PC in order for the Clone MAC

Address feature to work.

Click “OK” to nish the Cable Modem conguration; then you can start

using the router.

Fixed IP xDSL

Select if your Internet service provider has given you a specic IP address

for you to use. Your ISP should provide all the information required in

this section.

IP address assigned by your Service Provider — Enter the IP address

that your ISP has given you.

Subnet Mask — Enter the subnet mask provided by your ISP (for example,

255.255.255.0).

DNS — Enter the ISP’s DNS server IP address.

Gateway Address — Enter the ISP’s IP address gateway.

Click “OK” to nish the Fixed IP xDSL conguration; then you can start

using the router.

PPPoE

Select if your ISP requires the PPPoE protocol to connect you to the

Internet. Your ISP should provide all information required in this section.

User Name — Enter the username provided by your ISP for the PPPoE

connection.

Password — Enter the password provided by your ISP for the PPPoE

connection.

Service Name — This is optional. Enter the provided service name if

your ISP requires it; otherwise, leave this eld blank.

MTU — Enter the MTU value provided by your ISP for the PPPoE

connection.

Connection Type — Choose one of three drop-down menu options:

• “Continuous”: Keeps the router connected to the ISP. If the WAN

connection is disrupted and then re-linked, the router will automatically

reconnect to the ISP.

• “Connect On Demand”: Auto-connects the router to the ISP when

a user wants to use the Internet, and keeps it connected until the

WAN idle timeout. The router will close the WAN connection if the

Enter the IP Address, Subnet Mask, Gateway IP Address and DNS IP Address

provided to you by your ISP in the appropriate elds.

time period of Internet non-use exceeds the Idle Time setting.

• “Manual”: Connects the router to the ISP only when you click

“Connect” on the Web user interface. The WAN connection will not

disconnect due to the idle timeout, and if the WAN connection is

disrupted and re-linked, the router will not auto-connect to the ISP.

Idle Time — You can specify an idle-time threshold (in minutes) for the

WAN port. If no packets have been sent (no one has been using the

Internet) throughout this specied period, the router will automatically

disconnect from your ISP.

Click “OK” to nish the PPPoE conguration; then you can start using

the router.

PPTP

Select if your Internet service provider requires the PPTP protocol to

connect you to the Internet. Your ISP should provide all the information

required in this section.

Obtain an IP address automatically — When this is selected, you obtain

an IP address via the DHCP before connecting to the PPTP server.

Enter the Username and Password required by your ISP in the appropriate elds.

If your ISP has provided you with a Service Name, enter it in that eld; otherwise,

leave the eld blank.

Andere Handbücher für 524582

Inhaltsverzeichnis

Andere Intellinet WLAN-Router Handbücher

Intellinet

Intellinet 523455 Bedienungsanleitung

Intellinet

Intellinet 523967 Bedienungsanleitung

Intellinet

Intellinet 524780, 524797, 524872, 524896 Bedienungsanleitung

Intellinet

Intellinet 516624 Bedienungsanleitung

Intellinet

Intellinet 523233 Bedienungsanleitung

Intellinet

Intellinet 516211 Bedienungsanleitung

Intellinet

Intellinet 523431 Bedienungsanleitung

Intellinet

Intellinet 524315 Bedienungsanleitung

Intellinet

Intellinet 502566 Bedienungsanleitung

Intellinet

Intellinet 521604 Bedienungsanleitung

Intellinet

Intellinet 524315 Bedienungsanleitung

Intellinet

Intellinet 524988 Bedienungsanleitung

Intellinet

Intellinet 503693 Bedienungsanleitung

Intellinet

Intellinet 525312 Bedienungsanleitung

Intellinet

Intellinet 524360 (Annex A) Bedienungsanleitung

Intellinet

Intellinet 523967 Bedienungsanleitung

Intellinet

Intellinet 503693 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Intellinet

Intellinet 521666 Bedienungsanleitung

Intellinet

Intellinet 523431 Bedienungsanleitung

Intellinet

Intellinet 524803 Bedienungsanleitung

Intellinet

Intellinet 524681 Bedienungsanleitung

Intellinet

Intellinet 524957 Bedienungsanleitung

Intellinet

Intellinet 520454 Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Milesight

Milesight UG67 Bedienungsanleitung

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

NETGEAR

NETGEAR WNR2000v4 Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung

Draytek

Draytek Vigor2120 Series Bedienungsanleitung