Intellisystem ThermalTronix TT-1260S-UTCM Bedienungsanleitung

ThermalTronix

TT-1260S-UTCM

Thermal Imaging System

User Manual

Warning &Attention

Warnings

•

Please avoid aiming the lens at extreme high temperature radiation source, such as the sun,

molten steel or laser in any situation; otherwise the detector may be damaged.

•

Please do not touch the lens to avoid contaminating and damaging. Please pay attention to

protect the lens to avoid causing abrasion, scratches even breaches, otherwise, it will affect

the device performance badly, even damage the device.

•

This device is a precise optoelectronic product. Please protect it properly during usage,

storage and transportation, where improper use (such as drop and collision) will cause

damage to the device. If the internal connection is broken during the assembly process or the

apparatus is damped (rain wet), the performance will be reduced and even the device will be

damaged.

•

Make sure that the power control connection is reliable. If the power control wire is in bad

connection, it will damage the device.

•

Ensure the proper connection of power control cable and data cable. Wrong connection may

cause damage to the device.

•

Do not swag fiercely or collide the device during transportation, otherwise it will cause

performance-reduction and even damage to it.

•

Please use the specified power supply; otherwise it will cause improper working, even

damaging the apparatus.

If the product works abnormally, please contact the dealer or the nearest after-sale service center.

Please do not dismantle or replace it in any manners.

Table of Contents

Warning & Attention................................................................................. 1

Overview........................................................................................3

Getting started ............................................................................... 4

2.1 How to assembly..........................................................................................................4

2.2 Control panel...............................................................................................................4

2.3 Interfaces & connectors..............................................................................................6

2.3.1 Video output interface.......................................................................................6

2.3.2 Multiple interface..............................................................................................6

Operation guide.............................................................................7

3.1 Menu description.........................................................................................................7

3.1.1 Main menu ........................................................................................................7

3.1.2 Crosshair menu..................................................................................................8

3.1.3 Mode setup menu (user defined) ......................................................................9

3.1.4 Dead pixel correction menu ..............................................................................9

3.1.5 Factory default menu ......................................................................................10

3.2 Main operation description .....................................................................................11

3.2.1 Single pixel correction setup ..........................................................................11

3.2.2 Auto imaging mode setup ...............................................................................11

3.2.3 Imaging mode selection ..................................................................................12

3.2.4 User-defined imaging configuration setup ......................................................12

3.2.5 Gain setup .......................................................................................................12

3.2.6 Brightness setup .............................................................................................13

3.2.7 Polarity setup ..................................................................................................13

3.2.8 Filter setup ......................................................................................................13

3.2.9 Image enhancement setup ...............................................................................13

3.2.10 Calibration setup .............................................................................................14

3.2.11 Crosshair setup ...............................................................................................14

3.2.12 Dead pixel correction setup ............................................................................15

3.2.13 Focusing .........................................................................................................15

Troubleshooting........................................................................... 16

Technical specification................................................................17

1. Overview

The Figure.1.1 shows the overall dimension of the camera.

Figure.1.1 Overview of the camera

Figure.1.2 Back of the camera

2. Getting started

2.1

How to assembly

1. Check all units are in accordance with the packing list.

2. Make sure all parts are well protected in the carry case.

3. Carefully take out the camera and other accessories.

4. Connect the video connector to the monitor.

5. Connect the power adapter and power cable

6. Connect the power cable to the power supply to power on the camera.

2.2

Control panel

The camera provides a control panel with five shortcut keys with various functions. The below is

the figure of the control panel:

Figure.2.2.1 Control panel

The five keys have the below functions respectively:

UP key. When the menu is activated, press UP to adjust the selected parameters. The

parameter value will be increased after pressing. When the menu is not activated, press UP to

focus forwards.

DOWN key. When the menu is activated, press DOWN to adjust the selected

parameters. The parameter value will be decreased after pressing. When the menu is not

activated, press DOWN to focus backwards.

MEMU key. Press to activate or hide the menu. Press MENU to select the

parameter, and

modify the parameter value via UP or DOWN keys. Continuing pressing MENU key, the

function option will be selected circularly. After one cycle,

the menu will disappear and the

change will be saved. The parameter setting will

be the last-time setting after restarting next

time.

Calibration key. Long press (≥3s) to do calibration manually.

Cursor key. Press to activate the crosshair menu.

Table.2.2.1 Shortcut key combinations

No.

Combinations

Description

MENU+UP

Display the crosshair.

MENU+DOWN

Hide the crosshair.

F+UP

Activate Dead pixel correction menu (see 3.1.4)

F+DOWN

Activate Factory default menu (see 3.1.5)

UP+DOWN

Automatic focusing.

MENU+UP+DOWN

Activate Mode setup menu (see 3.1.3).

2.3

Interfaces & connectors

2.3.1

Video output interface

Figure.2.3.1.1 Video output interface

The above figure is a BNC video output interface.

2.3.2

Multipleinterface

Figure.2.3.2.1 Multiple interface

The definition of each pin is as below:

No.

Pin name

Description

+12V

Positive power end

GND

Power ground

RS485A

Com port

RS485B

Com port

I/O1

User port

I/O2

User port

I/O3

User port

I/O4

User port

I/O5

User port

COM

3. Operation guide

This chapter is mainly to show you how to execute the camera program. The program comprises

of five menus: main menu, crosshair menu, mode setup menu, dead pixel correction menu and

factory default menu. For more details, please see the following parts of contents.

3.1 Menu description

3.1.1 Main menu

Press MENU button to activate main control menu. Press UP or DOWN button to change the

option value. Keep pressing MENU button until menu prompt disappeared to exit.

Auto:2

Mode:2

G:15

B:16

P:1

F:Y

E:N

AF:N

C:0

ID:0

Protocol:PELCO-D

Figure.3.1.1.1 Main menu interface

Auto: X Display the current image auto mode. Three options:

0: manual gain, manual brightness;

1: manual gain, auto brightness;

2: auto gain, auto brightness;

Mode: X Display the current image mode. There are 10 options, where 0 and 1 are

fixed factory default settings and 2-9 are user-defined settings.

0: Suitable for observation of big-object under good weather condition

1: Suitable for observation of target within sky-line under good weather

condition 2～9: User-defined based on different practical occasion

Note: when Auto 0 and 1, Mode X cannot be adjusted; when Auto 2, Mode X can be

adjusted.

G: XXX Gain value, range: 0-255

B: XXXXX Brightness value, range: -2048-+2048

G: XXX Gain value, range: 0-255

B: XXXXX Brightness value, range: -2048-+2048

P: X White/black hot display mode

0: black hot 1: white hot

F: X Filter status (on/off)

Y: on N: off

E: X Image enhancement status

Y: on N: off

AF: X Automatic focusing.

Y: on N: off

C: XXX Adjust non-uniformity parameter value.

ID: XXX ID number, range: 0-255.

Protocol: XXX Select the communication protocol. Two options: PELCO-D and

PELCO-P.

Note: When exiting the main menu, any change will be saved automatically and will be used

when

restarting next time.

Mode: X can only choose the existed mode, but cannot adjust it.

3.1.2 Crosshair menu

Press F button to activate crosshair menu. Press UP or DOWN button to change the option value.

Cur: N X:192 Y:144 Exit:

Figure.3.1.2.1 Crosshair menu interface

Cur: X Y-display the cursor; N-hide the cursor;

X: XXX Display the crosshair position in X-axis;

Y: XXX Display the crosshair position in Y-axis, range;

Exit Exit crosshair menu. Press MENU button to select the Exit option and press

UP button to exit the menu.

3.1.3 Mode setup menu (user defined)

User can define the mode, as they want. They can define eight modes from mode 2 to mode 9.

Press MENU button, DOWN button and UP button at the same time to activate user-defined

configuration setup menu. Press UP or DOWN button to change the option value.

Mode: 2 Gain: 32 Bright: 188 Save: Exit:

Figure.3.1.3.1 Mode setup menu

Mode: X Display the mode number.

G: XXX Gain value, range: 0-255;

B: XXX Brightness value, range: 0-255;

Save: Save configuration setup

Exit: Exit configuration setup. Press MENU button to select the Exit option

and press UP button to exit the menu.

Note: The Mode X displayed on the main menu interface will be the current mode.

3.1.4 Dead pixel correction menu

User can manually correct the dead pixel single by single or correct all dead pixels

automatically

by the camera.

Press F button and UPbutton at the same time to activate dead pixel correction menu.

X: XXX Y: XXX Ent: Esc:

Figure.3.1.4.1 Dead pixel correction menu interface

Inhaltsverzeichnis

Andere Intellisystem Multifunktionsdrucker Handbücher

Intellisystem

Intellisystem ThermalTronix TT-1025EX-MIL Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung