Intergraph ErgoView Stand Bedienungsanleitung
ErgoView Stand
Installation Guide
March 1998
DFED3607M
Copyright
1998 Intergraph Computer Systems. All rights reserved. This document contains information protected by copyright, trade secret, and trademark
law. This document may not, in whole or in part, be reproduced in any form or by any means, or be used to make any derivative work, without written
consent from Intergraph Computer Systems.
Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of the rights in technical
data and computer software clause at DFARS 252.227-7013. Unpublished rights are reserved under the copyright laws of the United States.
Intergraph Computer Systems, Huntsville AL 35894-0001
Notice
Information in this document is subject to change without notice and should not be considered a commitment by Intergraph Computer Systems.
Intergraph Computer Systems shall not be liable for technical or editorial errors in, or omissions from, this document. Intergraph Computer Systems
shall not be liable for incidental or consequential damages resulting from the furnishing or use of this document.
All warranties given by Intergraph Computer Systems about equipment or software are set forth in your purchase contract. Nothing stated in, or
implied by, this document or its contents shall be considered or deemed a modification or amendment of such warrantites.
Trademarks
Intergraphand the Intergraph logo are registered trademarks of Intergraph Corporation. ErgoView is a trademark of Intergraph Corporation. Other
brands and product names are trademarks of their respective owners.
Contents
1 ErgoView Stand Installation....................................................................................1
2 Unpacking the Digitizing Table and Base...............................................................2
3 Unpacking the ErgoView Stand ..............................................................................4
4 Installing the Monitor..............................................................................................5
CLIX Workstation Monitor............................................................................................5
Removing the Swivel Base...............................................................................5
Installing a 19-, 20-, or 21-inch Monitor ..........................................................5
Installing a 27-inch Monitor ............................................................................5
Hitachi OEM Monitor....................................................................................................6
Removing the Swivel Base...............................................................................6
Attaching the Adapter Bracket .........................................................................6
Replacing the Monitor Collar...........................................................................7
Installing the Monitor ......................................................................................7
Panasonic OEM Monitor ...............................................................................................8
Preparing the Monitor for Installation ..............................................................9
Replacing the Monitor Collar.........................................................................12
Installing the Monitor ....................................................................................13
5 Connecting the Cables ...........................................................................................15
Single ErgoView Stand................................................................................................15
Dual ErgoView Stands.................................................................................................18
6 Replacing a CLIX Workstation Monitor..............................................................20
1
1 ErgoView Stand Installation
This document describes how to install single- or dual-monitor ErgoView workstation stands with
digitizing table configurations. Read all of the instructions completely before beginning the
installation.
WARNING The following procedures are to be performed by Intergraph Computer Systems service
personnel only, and are not intended for use by customers.
This document describes cable kit installations to make either an Intergraph Computer Systems or
Hamilton table base compatible with the ErgoView stand. The ErgoView stand provides the
mechanical structure to support the following monitors:
19-inch MDSP090, MDSP099, MESAJ44, MDSP102
20-inch MDSP126
21-inch MDSP108, MDSP127, MDSP131, MDSP139, MDSP142, MDSP147
27-inch MDSP072, MDSP097, MDSP098
CAUTION Damage may occur to this equipment if installed in a factory or shop environment where oil, dust, or
other airborne contaminants are present.
To unpack and install the digitizing table, ErgoView stand, and monitor, you will need the help of
one person, and the following tools and equipment:
u
Hand truck
u
Diagonal cutting pliers
u
Single-slot screwdriver
u
Adjustable wrench
u
No. 1 Phillips screwdriver
u
No. 2 Phillips screwdriver
u
Socket wrench (1/4 or 3/8-inch drive) and 9/16-inch socket
u
Sharp knife
2
2 Unpacking the Digitizing Table and Base
The digitizing table and base are shipped already assembled together. If your installation site has an
existing digitizing table with an Intergraph Computer Systems or Hamilton table base, go to
“Unpacking the ErgoView Stand.”
WARNING To avoid injury, stand to the side when cutting the package banding.
CAUTION Do not penetrate packaging with sharp instruments.
1. Carefully cut the package bands around the box and pallet. See the following figure.
2. Lift the box off the pallet.
3. Remove the plastic wrap from the table base.
WARNING The digitizing table is top-heavy and can tip over while locked in a vertical position.
4. Using a socket wrench with a 9/16-inch socket, remove the hex head bolts that secure the table
brackets to the pallet.
Ramps
Table
Bracket
Table
Bracket
Bands
5. Unlock the table tilt mechanism (located underneath the table) by moving the handle of the tilt
mechanism towards the center of the table. Rotate the digitizing table to a horizontal position.
6. Lock the table in the horizontal position by moving the handle of the tilt mechanism towards the
outside of the table. Remove the table brackets.
3
7. Remove the four bolts that secure the table base to the pallet. The bolts are accessible from
underneath the pallet.
8. Remove the wooden blocks from underneath the legs of the table base.
9. Remove the two bolts that secure the ramps to the pallet.
10. Slide the ramps from under the digitizing table base. Mount the ramp tabs into the slots at the
front of the pallet.
11. With a person at each side of the table, carefully roll the digitizing table down the ramps.
12. Place the digitizing table in the area where you will be installing the ErgoView stand.
WARNING Do not connect the power cable to the AC power outlet at this time.
See “Unpacking the ErgoView Stand” to continue.
4
3 Unpacking the ErgoView Stand
WARNING To avoid injury, stand to the side when cutting the package banding.
1. Carefully cut the package banding around the box and pallet.
2. Lift the box off the pallet.
3. Remove the plastic wrap from the stand.
4. Using a socket wrench and a 9/16-inch socket, remove the four hex head bolts securing the stand
to the pallet. The bolts are accessible from underneath the pallet.
5. Remove the wooden blocks from underneath the legs of the stand.
6. Using a socket wrench and a 9/16-inch socket, remove the bolts securing the ramps to the pallet.
7. Slide the ramps off the pallet and mount them into the slots at the front of the pallet.
8. With a person at each side of the stand, carefully roll the stand down the ramps.
9. Place the stand near a wall outlet. Allow 36 inches of clearance at the back of the stand for
operator and service access.
WARNING Do not connect the power cable to the AC power outlet at this time.
CAUTION The ErgoView stand must be connected to an unobstructed AC power wall outlet.
See “Installing the Monitor“ to continue.
5
4 Installing the Monitor
Some monitors are shipped with the swivel bases installed. If so, you must remove the swivel base
before installing the monitor into the ErgoView stand.
CLIX Workstation Monitor
Removing the Swivel Base
WARNING The monitor is heavy and could cause serious personal injury if dropped. Two persons should
lift and carry the monitor.
1. Unpack the monitor from its shipping carton.
2. Verify that the monitor power cord is supplied.
3. Turn the monitor onto its side.
WARNING Do not set the monitor on its display screen. Damage may result.
4. Remove the two Phillips screws which have washers beneath them from the swivel base.
5. Rotate the swivel base to expose two of the four M5 Phillips pan head screws. Remove the two
screws, rotate the base 180 degrees, and remove the remaining two screws.
6. Remove the swivel base.
Installing a 19-, 20-, or 21-inch Monitor
1. Lock the ErgoView stand tilt adjustment knob, located where the monitor collar attaches to the
ErgoView stand.
2. Set the monitor into the collar.
WARNING Ensure that one person holds the top of the monitor to prevent it from tipping downward when
initially placed in the monitor collar.
3. Thread the four M5x25mm Phillips flat head screws through the bottom of the cover plate
(attached to the bottom of the collar) and into the monitor housing.
4. Tighten all screws.
See “Connecting the Cables” to finish setting up the ErgoView stand.
Installing a 27-inch Monitor
1. Lock the ErgoView stand tilt adjustment knob, located where the monitor collar attaches to the
ErgoView stand.
2. Locate the two screws in the upper corners of the back of the monitor. Remove the outer screw
from each of these corners.
3. Set the monitor into the collar and align the screw holes with the tabs extending from the top of
the collar.
WARNING Ensure that one person holds the top of the monitor to prevent it from tipping downward when
initially placed in the monitor collar.
6
4. Thread the two M3x12mm Phillips pan head screws with M4 oversized washers through the
collar tabs and into the monitor housing. Do not tighten the screws yet.
5. Thread the four M5x25mm Phillips flat head screws through the bottom of the cover plate
(attached to the bottom of the collar) and into the monitor housing.
6. Tighten all screws.
See “Connecting the Cables” to finish setting up the ErgoView stand.
Hitachi OEM Monitor
The hardware kit (MKIT120) used to install the Hitachi monitor contains the following items:
u
One monitor cover plate, CFAB329E
u
One pivot cover, CFAB331E
u
One adapter bracket, CFAB330F (MDSP139)
u
One adapter bracket, CFAB250G (MDSP147)
u
One rear bracket, CFAB331F
u
OEM monitor collar, MMSA3530
u
Six M4x8mm screws, CPHM022
u
One-inch foam tape CPTP076 (for CFAB329E)
u
Three-quarter-inch adhesive tape CPTP077 (for CFAB331E)
Removing the Swivel Base
WARNING The monitor is heavy and could cause serious personal injury if dropped. Two persons should
lift and carry the monitor.
1. Unpack the monitor from its shipping carton.
2. Verify that the monitor power cord is supplied.
3. Turn the monitor onto its side.
WARNING Do not set the monitor on its display screen. Damage may result.
4. Rotate the base until the two screws can be seen.
5. Remove and retain the two screws.
6. Slide the base to the back of the monitor and set the base aside.
Attaching the Adapter Bracket
1. Place the appropriate adapter bracket onto the bottom of monitor. Ensure the holding latches are
secured inside the slots in the monitor frame. See the following figure.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Intergraph Computerzubehör Handbücher
Intergraph
Intergraph TDZ 2000 Kurzanleitung
Intergraph
Intergraph TDZ 2000 Benutzerhandbuch
Intergraph
Intergraph ImageStation ZIII and use Kurzanleitung
Intergraph
Intergraph ExtremeZ SAN Bedienungsanleitung
Intergraph
Intergraph InterServe 650 ?anual Handbuch
Intergraph
Intergraph ExtremeZ SAN Bedienungsanleitung
Intergraph
Intergraph InterServe 8000 Handbuch
Intergraph
Intergraph InterServe 3x5 Handbuch
Intergraph
Intergraph ImageStation Z and use Kurzanleitung
Intergraph
Intergraph StudioZ GT RAX Benutzerhandbuch
