Interlink electronics VersaPoint Bedienungsanleitung

Users Manual

VersaPoint Rechargeable Wireless Desktop Suite

Regulatory Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause undesired operation.

FCC Certication

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Consult the dealer or an experienced radio/TV technician for help.

Notice: Any changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. Extension cables are not

recommended, if used, they must be shielded in order to comply with the emission limits.

IC Certication

The term “IC” before the certication/registration number only signies that the Industry

Canada technical specications were met.

Declaration of conformity

Hereby, Interlink Electronics, Inc. declares that this VersaPoint Wireless Desktop Suite is in

compliance with the essential requirements and other relevant provisions of Directive 1999/5/

EC. All trademarks and registered trademarks mentioned in this document are the property of

their respective owners.

Features and specications are subject to change without notice.

System Requirements

Hardware: Desktop or notebook system with 1 available

USB 1.1 or 2.0 port

Operating System: Windows 2000, XP or Vista

Package Contents

• 2.4GHz rechargeable keyboard

• 2 x AAA rechargeable Ni-MH batteries (for the keyboard)

• 2.4GHz rechargeable mouse

• 2 x AA rechargeable Ni-MH batteries (for the mouse)

• USB RF receiver with pass through charging port

• Charging cable

• User’s manual

Installing the Keyboard

• Remove the battery cover located at the bottom of the

keyboard.

• Insert the two supplied AAA rechargeable Ni-MH batteries

(included in the package) into the battery compartment.

Page 1

Make sure the positive (+) and negative (-) ends of the

batteries match the polarity markings inside the battery

compartment.

• Snap the battery cover back into position.

Installing the Mouse

Page 2

• Remove the battery cover located at the bottom of the

mouse.

• Insert the two supplied AA rechargeable Ni-MH

batteries (included in the package) to the battery slots.

Make sure the positive (+) and negative (-) ends of the

batteries match the polarity markings inside the battery

compartment.

• Snap the battery cover back into position.

Charging the Batteries

• It’s recommended that

you fully charge the

batteries before initial use;

nevertheless it’s ready

for set up (see next step)

anytime during charging.

Page 3

Do not attempt to charge non-rechargeable disposable Alkaline

batteries. The batteries may leak and damage your mouse

or keyboard. Use only the rechargeable Ni-MH batteries

supplied. Shall replacing batteries become necessary use only

rechargeable Ni-MH batteries. Do not mix new and old batteries

or batteries of different brands or capacities in the products.

• Connect the charging cable (included in the box) to the

USB RF receiver’s charging port and the mouse. (Repeat

this step later for the keyboard.)

• Plug the receiver’s USB connector to your computer’s

available USB port.

• The initial charging process may take up to 8 hours.

Subsequent recharge may require less time depending on

the level of residual power in the batteries.

• Repeat these steps to charge the keyboard. Unplug the

charging cable from the mouse and connect it to the

keyboard’s charging port.

• The keyboard and mouse are operational during charging;

you can continue use the products while charging via the

USB charging cable.

• You are now ready to connect the keyboard and mouse to

your computer. (Note: it’s not necessary to wait for the

batteries to be fully charged before connecting to your

system.)

Page 4

Connecting the Keyboard & Mouse to the

Computer

• Connect the RF receiver to an available USB port on your

computer. This may have been done when batteries are

being charged.

• The radio frequency (RF) codes are factory preset for

your convenience; the keyboard and mouse should be

functional at this point.

• If for any reason the keyboard and/or mouse do not

Page 5

Make sure the computer’s power management is set to disable

hibernation mode while the products are being charged. (Go to

Control Panel, Power Options, select “Hibernate” from the tabs

and uncheck the box marked “Enable Hibernation.)

function correctly, i.e. no cursor movements or sluggish

cursor movements, there may be other wireless devices in

the vicinity operating in the same radio frequency channel.

The keyboard and mouse can be easily reset to another

channel.

• To connect the mouse to your system, press the connect

button located at the bottom of the RF receiver (1) while

it’s connected to the computer’s USB port, and press the

connect button located at the bottom of the mouse (2).

This will reset the mouse and the RF receiver to a different

channel to avoid interference.

• To connect the keyboard to your system, press the connect

button located at the bottom of the RF receiver (1) while

it’s connected to the computer’s USB port, and press the

connect button located at the upper right-hand corner of

the keyboard (3). This will reset the keyboard and the RF

receiver to a different channel to avoid interference.

• This step can be repeated when needed.

Page 6

Operating Instructions

Using the Keyboard

• This keyboard features the standard 104-key QWERTY

conguration plus 15 convenient one-touch hot keys and a

volume control wheel.

Page 7

Page 8

Andere Handbücher für VersaPoint

Inhaltsverzeichnis

Andere Interlink electronics Computerzubehör Handbücher

Interlink electronics

Interlink electronics DuraPoint Bedienungsanleitung

Beliebte Computerzubehör Handbücher anderer Marken

Motorola

Motorola ATRIX Bedienungsanleitung

HP USB Media Docking Station Bedienungsanleitung

Cherry

Cherry B.UNLIMITED 3.0 Bedienungsanleitung

Logitech

Logitech IO2 Bedienungsanleitung

ARM

ARM DSTREAM-ST Bedienungsanleitung

Bartec

Bartec TC 7 Series Bedienungsanleitung

Philips

Philips SPC3540 Bedienungsanleitung

Logitech

Logitech mk220 Bedienungsanleitung

SilverStone

SilverStone LC02 Bedienungsanleitung

Flexispot

Flexispot ML2B Bedienungsanleitung

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Bedienungsanleitung

Adam Equipment

Adam Equipment RS-485 Bedienungsanleitung

Vivo

Vivo MOUNT-KB05-4DW Bedienungsanleitung

Kvaser

Kvaser Memorator Professional Bedienungsanleitung

DRC

DRC D-Imaging Bedienungsanleitung

Sven

Sven Base 305 сombo Bedienungsanleitung

Hama

Hama 108310 Bedienungsanleitung

SpeechWare

SpeechWare FlexyMike FMK03 Bedienungsanleitung