Intermec Trakker Antares 2455 Bedienungsanleitung
TRAKKER Antares
®
2455 Keyboard
P/N 067363-002
Installation Guide
Intermec Technologies Corporation
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
U.S. service and technical support: 1-800-755-5505
U.S. media supplies ordering information: 1-800-227-9947
Canadian service and technical support: 1-800-688-7043
Canadian media supplies ordering information: 1-800-268-6936
Outside U.S. and Canada: Contact your local Intermec service supplier.
The information contained herein is proprietary and is provided solely for the purpose of allowing customers
to operate and/or service Intermec manufactured equipment and is not to be released, reproduced, or used for
any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change without notice.
1999 by Intermec Technologies Corporation
All Rights Reserved
The word Intermec, the Intermec logo, TRAKKER, and Antares are either trademarks or registered trademarks
of Intermec Technologies Corporation.
Throughout this manual, trademarked names may be used. Rather than put a trademark (or ) symbol in
every occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and
to the benefit of the trademark owner, with no intention of infringement.
T2455 Keyboard Installation Guide
3
TRAKKER Antares 2455 Keyboard Installation Guide
This installation guide explains how to install your TRAKKER Antares®2455 (T2455)
keyboard.
2455I.001
The T2455 keyboard assembly kit includes the following:
• Keyboard
• #8 straight-slot screws, ½-inch (12.7 mm) long (4)
• #8 straight-slot screws, ¼-inch (6.35 mm) long (4)
• #8 Phillips screws, .375-inch (9.52 mm) long, with cone washers (4)
• Hinges (2)
• Keyboard mounting brackets (2)
• Delrin washers, .04 inches (1 mm) thick (4)
• Stainless steel washers, .125 inches (3.18 mm) thick (2)
• Adjustment knobs (2)
Preparing to Install the T2455 Keyboard
You need the following tools and materials to install your T2455 keyboard:
• Cotton swabs
• Isopropyl alcohol
• Straight-slot screwdriver
• #1 Phillips screwdriver
T2455 Keyboard Installation Guide
4
Installing the Keyboard Overlay
Your terminal shipped with a keyboard overlay. You can install the overlay on your
keyboard.
To install the keyboard overlay
1. Clean the keyboard surface using a cotton swab moistened with isopropyl alcohol.
Allow the surface to dry.
2. Remove the backing from the overlay and carefully position the overlay on the
keyboard.
3. Use a dry cotton swab to firmly rub the overlay down between the keys and around
the edges of the keyboard.
Mounting the Keyboard
You can mount the keyboard directly to the T2455 terminal, or you can mount it to a
remote location, such as the dashboard of your vehicle.
Mounting the Keyboard to the Terminal
You can mount your keyboard to the terminal using the hardware provided. If the
terminal is already installed on the terminal mounting bracket, you need to remove the
terminal from the bracket to install the keyboard. See the TRAKKER Antares 2455
Vehicle-Mount Terminal Getting Started Guide (Part No. 067359) for more
information.
To mount the keyboard to the terminal
1. Position the keyboard so that you can easily access the threaded mounting holes in
the top of the keyboard.
2. Position one hinge so that the side of the hinge that has the tension screw is flush
against the keyboard, and align the holes in the hinge with the mounting holes in
the keyboard.
3. Secure the hinge to the keyboard using two of the ½-inch (12.7 mm) long #8
straight-slot screws and the straight-slot screwdriver.
T2455 Keyboard Installation Guide
5
Attaching the Hinges to the Keyboard
2455I.002
Tension
screw
4. Repeat Steps 2 and 3 for the other hinge.
5. Position the T2455 so the four mounting holes in the bottom of the terminal are
facing up.
6. Align the mounting holes in the bottom of the terminal with the remaining holes in
the hinges. Secure each hinge to the terminal using the ¼-inch (6.35 mm) long #8
straight-slot screws.
2455I.003
Screw
(4 places)
Keyboard
mounting
bracket
holes
7. Use the Phillips screwdriver to tighten the tension screw in each hinge so that
keyboard motion is slightly resisted. Do not over-tighten. The tension screw helps
to hold the keyboard in place when you loosen the adjustment knobs.
8. Rotate the keyboard out of the way so that you can access the keyboard mounting
bracket holes in the terminal.
T2455 Keyboard Installation Guide
6
9. Position one keyboard mounting bracket against the terminal as shown in the
following illustration. Loosely secure the bracket to the terminal using the #8
Phillips screws with cone washers and the Phillips screwdriver. Slide the bracket to
the outermost position.
2455I.004
Keyboard
mounting
bracket Stainless
steel
washer
Adjustment
knob
Delrin
washer
Philips screws
and cone washers
(4 places)
10. Rotate the keyboard into position next to the bracket. Insert one delrin washer
between the mounting bracket and the keyboard. Slide the bracket in until it
touches the washer.
11. Carefully rotate the keyboard out of the way and remove the delrin washer, while
maintaining the position of the bracket. Secure the bracket into place by tightening
the #8 Phillips screws with cone washers.
12. Repeat Steps 9 through 11 for the other bracket.
13. Place one stainless steel washer and one delrin washer, in that order, on each
adjustment knob.
14. Reinsert one delrin washer between the mounting bracket and the keyboard.
15. Insert one adjustment knob with washers through the mounting bracket and delrin
washer, and into the keyboard.
16. Repeat steps 14 and 15 for the other adjustment knob.
17. Position the keyboard to the desired angle and tighten the adjustment knobs.
18. Follow the instructions in “Connecting the Keyboard Cable to the Terminal” later
in this installation guide to complete your keyboard installation.
T2455 Keyboard Installation Guide
7
Mounting the Keyboard to a Remote Location
You can mount the keyboard to a remote location, rather than to the terminal. For
instance, you can mount the keyboard to the dashboard of your vehicle. To create your
own mounting surface, see “Specifications” later in this installation guide for the
keyboard dimensions.
To mount the keyboard to a remote location, you need to provide:
• Mounting hardware, including four #8 screws. The screws must be long enough to
go through the mounting surface and engage in the four threaded mounting holes in
the back of the keyboard. The holes in the keyboard are .375-inch (9.52 mm) deep.
• Electric drill and drill bit.
To mount the keyboard to a remote location
1. Determine the mounting locations for the terminal and the keyboard. Mount the
terminal as instructed in the TRAKKER Antares 2455 Vehicle-Mount Terminal
Getting Started Guide (Part No. 067359).
2. Use a #1 Phillips screwdriver to remove the six screws that secure the back plate to
the keyboard. Save the screws.
3. You can use the back plate as a template to mark and drill four holes in the
mounting surface.
4. Route the keyboard cable to the terminal. Tie off the cable at least every 18 inches
(45 cm). Store excess cable in the back of the keyboard.
5. Route the cable through the cable hole in the top of the keyboard housing, and then
reinstall the back plate using the six screws removed in Step 2.
6. Mount the keyboard using your #8 screws and the threaded mounting holes in the
back plate of the keyboard.
7. Connect the keyboard cable to the terminal. For help, see “Connecting the
Keyboard Cable to the Terminal” later in this installation guide.
T2455 Keyboard Installation Guide
8
Mounting the Keyboard to a Remote Location
2455I.005
Mounting
screw
(4 places)
Back
plate
screw
(6 places)
Keyboard
Connecting the Keyboard Cable to the Terminal
Now that you have installed your keyboard, you need to connect it to the terminal.
1. Remove the rubber plug from the Keyboard port on the terminal.
2. Push the keyboard cable connector straight into the Keyboard port. The icon on the
keyboard cable connector should align with the same icon on the back of the
T2455.
Note: Firmly push the keyboard cable connector straight into the Keyboard port.
Do not wiggle or twist the keyboard cable connector to seat the connector in the
port—you may damage the connector.
T2455 Keyboard Installation Guide
9
Connecting the Keyboard Cable to the Terminal
2455I.006
Keyboard
cable connector
Keyboard
3. Use the straight-slot screwdriver to tighten the screws in the keyboard cable
connector and secure the cable to the T2455.
4. Tuck any excess cable into the back of the keyboard.
5. If you attached the keyboard directly to the terminal, you need to mount the
terminal and keyboard in the terminal mounting bracket. See the TRAKKER
Antares 2455 Vehicle-Mount Terminal Getting Started Guide (Part No. 067359) for
more information.
Specifications
Use the dimensions provided in the following illustrations to create your own keyboard
mounting bracket or enclosure.
T2455 Keyboard Installation Guide
10
Keyboard Back Plate Specifications
9.695 in
24.625 cm
7.570 in
19.23 cm
3.78 in
9.6 cm
.562 in
1.43 cm
.21 in
5.334 mm
1.69 in
4.29 cm
1.063 in
2.7 cm
4X ∅ .164-32 UNC-2B
↓.375 in min
9.525 mm
1.062 in
2.7 cm
2X 3.379 in
8.58 cm
.186 in
4.72 mm
2455I.007
Note: This keyboard back plate illustration is not shown to scale.
Keyboard Specifications (Top View)
2455I.008
5.62 in
14.27 cm
.31 in
7.874 mm .41 in
10.414 mm
Cable exit location
11.24 in
28.55 cm
Note: This keyboard illustration is not shown to scale.
Andere Handbücher für Trakker Antares 2455
3
Inhaltsverzeichnis
Andere Intermec PDA Handbücher
Intermec
Intermec CK30 Bedienungsanleitung
Intermec
Intermec CK60 Ethernet Multidock Handbuch
Intermec
Intermec CN70 RFID Bedienungsanleitung
Intermec
Intermec CN51 Bedienungsanleitung
Intermec
Intermec CN70G Bedienungsanleitung
Intermec
Intermec 6600 Bedienungsanleitung
Intermec
Intermec Trakker Antares 2410 Bedienungsanleitung
Intermec
Intermec 700 Series 730B Bedienungsanleitung
Intermec
Intermec 70 Bedienungsanleitung
Intermec
Intermec 6110 Gebrauchs- und Pflegehandbuch
Intermec
Intermec CN 70 Bedienungsanleitung
Intermec
Intermec 700 Series 730B Handbuch
Intermec
Intermec PEN*KEY 6400 Bedienungsanleitung
Intermec
Intermec 5023 Montage- und Bedienungsanleitung
Intermec
Intermec PEN*KEY 6100 Bedienungsanleitung
Intermec
Intermec 6300 SERIES Bedienungsanleitung
Intermec
Intermec CV60 Bedienungsanleitung
Intermec
Intermec Janus 900 Bedienungsanleitung
Intermec
Intermec PEN*KEY 6400 Handbuch
Intermec
Intermec NORAND 6642 Bedienungsanleitung
