IntesisBox BACnet/IP Server-DALI Bedienungsanleitung

IntesisBox®BACnet/IP Server –DALI

Installation Manual

The information in this document may change without previous notice.

Doc. Rev.1

URL

tel

http://www.intesis.com

[email protected]m

+34 938047134

1 / 5

Safety Instructions

WARNING

Installation Instructions

Configuration and Setup

Use the software LinkBoxBacnet to configure IntesisBox. Follow User’s Manual instructions for detail on the configuration process.

See instructions to download and install the latest version of LinkBoxBacnet and

its user's manual at

http://www.intesis.com/down/bacnet/linkboxbacnet.html

IntesisBox must be installed by accredited electrician or similar technical personnel, following all the safety instructions

given here, and in accordance always with the country legislation for installation of electric equipment.

IntesisBox can not be installed outdoors or exposed to direct solar radiation, water, high relative humidity or dust.

IntesisBox must only be installed in a restricted access location.

In case of wall mount, fix firmly IntesisBox on a not vibrating surface following the instructions below.

In case of DIN rail mount fix IntesisBox properly to the DIN rail following the instructions below.

Mounting on DIN rail inside a metallic cabinet properly connected to earth is recommended.

Disconnect always power of any wires before manipulating and connecting them to IntesisBox.

Respect always the expected polarity of power and communication cables when connecting them to IntesisBox.

Supply always a correct voltage to power IntesisBox, within voltage range admitted (230Vac +/ -10%).

This device was designed for installation in an enclosure. To avoid electrostatic discharge to the unit in environments with

static levels above 4 kV precautions should be taken when the device is mounted outside an enclosure. When working in

an enclosure (ex. making adjustments, setting switches etc.) typical anti-static precautions should be observed before

touching the unit

Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your

health and also may damage seriously the IntesisBox and/or any other equipment connected to it.

Disconnect the mains power and power of any bus or communication cable before connecting it to IntesisBox.

Mount IntesisBox on the wall or DIN rail following the instruction given below, respecting the safety instructions given

above.

Connect the mains power cable to the supply voltage terminal block of IntesisBox.

Circuit-breaker must be used before the mains power cable. Rating 250V-6A

Connect the communication cables to IntesisBox, see details on the user's manual.

Power IntesisBox and the rest of devices connected to it.

After power-on, DALI bus LED (at the left side of DALI connector) should be ON, signalling that there is DALI bus voltage.

If DALI bus LED is OFF, you should check the DALI communication line for a possible short-circuit.

If your DALI installation is already operative, communication at DALI side can be tested by pressing the DALI test button:

Pressing once the button, the ballasts will switch ON (DALI led will start flashing)

Pressing again the button, the ballasts will switch OFF (DALI led will toggle to ON)

Pressing again the button, the ballasts will switch ON, and remain ON until their value is changed from BACnet side

(DALI led will toggle to OFF, signaling that the test has ended).

IntesisBox®BACnet/IP Server –DALI

Installation Manual

The information in this document may change without previous notice.

Doc. Rev.1

URL

tel

http://www.intesis.com

[email protected]m

+34 938047134

2 / 5

Wall mounting

1. Separate the fixing clips in the bottom of the box, pushing them to the outside until hearing the "click"

which indicates that now the clips are in position for wall mount, see in the figure below.

2. Drill 3 holes in the wall following as a guide the distances shown below. Use the holes of the clips

to fix the box in the wall, using screws.

DIN rail mounting

With the clips of the box in their original position, insert first the box in the upper edge of the DIN rail. Then insert

the box in the down part of the rail, using a small screwdriver, following the steps in the figure below.

Bottom view of the box

Clips in their original position, for DIN-rail mounting

Clips in wall-mount position

Top view of the box

97,5 mm

114 mm

Ø 3 mm

IntesisBox®

www.intesis.com

23 mm

79 mm

DIN Rail

(EN60715 TH35)

Side view of the box

IntesisBox®BACnet/IP Server –DALI

Installation Manual

The information in this document may change without previous notice.

Doc. Rev.1

URL

tel

http://www.intesis.com

[email protected]m

+34 938047134

3 / 5

Connections

________________________________________________________________________________________

Notes:

1. BACnet/IP connection: Use a crossover ethernet CAT5 cable if connecting directly to a BACnet/IP controller, or a straight ethernet CAT5

cable if connecting to a hub or switch of the LAN in the installation. If communicating through a LAN you might need to contact the network

administrator to make sure UDP traffic and port used for BACnet/IP (default is 47808) are allowed throughout the LAN path between

IntesisBox and your BACnet client.

DALI connection: Connect DALI bus to the DALI connector of IntesisBox. IntesisBox provides 15Vdc (+/-2%) DALI voltage to the bus.

2. Use the software LinkBoxBacnet to configure IntesisBox. Consult user's manual for details.

LinkBoxBacnet

Only needed for

configuration,

configuration can also be

done using Ethernet

See Note 2

DALI Bus

See Note 1

Mains Power

230V ac

Ethernet / BACnet/IP

(and IntesisBox configuration)

See Note 1

PC Console

IntesisBox®

www.intesis.com

- +

N L

POWER

230VAC 6W

DALI

Console cable 1,8 m.

Standard DB9 Female - DB9 Male.

(supplied with IntesisBox)

Serial Port

(Not used)

ETH

(BACnet/IP)

IntesisBox®BACnet/IP Server –DALI

Installation Manual

The information in this document may change without previous notice.

Doc. Rev.1

URL

tel

http://www.intesis.com

[email protected]m

+34 938047134

4 / 5

Technical characteristics

Enclosure

Plastic, type PC (UL 94 V-0).

Dimensions: 159mm 105mm x 58mm.

Color

Light Grey / RAL 7035.

Supply Voltage

230Vac +/-10% 6W

(3-pole plug-in terminal block –line, neutral and earth)

Terminal wiring

(for power supply

and low-voltage

signals)

Per terminal: solid wires or stranded wires (twisted or with

ferrule)

1 core: 0.5mm2… 2.5mm2

2 cores: 0.5mm2… 1.5mm2

3 cores: not permitted

Mounting

Wall.

DIN rail EN60715 TH35.

DALI bus power

source

15Vdc +/-2% 250mA.

(DALI bus is powered from IntesisBox)

DALI port

1 x DALI electrically isolated (2-pole plug-in terminal block). SELV

Ethernet port

(BACnet/IP, device

config)

1 x Ethernet 10Base-T (RJ45).

LED indicators

1 x Power indicator.

2 x DALI activity (Tx, Rx).

2 x Ethernet link & activity (LNK, ACT).

1 x DALI bus power

1 x DALI test1

Push buttons

1 x DALI test1

Console port

EIA232. DB9 female connector (DCE). SELV

Configuration

Via Ethernet or serial console port.2

Firmware

Allows upgrades via console port.

Operational

temperature

0°C to +60°C

Operational

humidity

25-90% at 50ºC, non condensing

Protection

IP20 (IEC60529).

RoHS conformity

Compliant with RoHS directive (2002/95/CE).

Norms and

standards

CE conformity to EMC directive (2004/108/EC) and Low-voltage

directive (2006/95/EC)

EN 61000-6-2

EN 61000-6-3

EN 60950-1

EN 50491-3

1DALI test push-button and LED are meant to perform a quick test of your DALI line and connected ballasts.

2Standard cable DB9male-DB9female 1,8 meters long is supplied with the device for connection to a PC COM port for

configuring and monitoring the device using the serial port (Ethernet is also possible). The configuration software, compatible

with Windows®operating systems, is also supplied.

IntesisBox®BACnet/IP Server –DALI

Installation Manual

The information in this document may change without previous notice.

Doc. Rev.1

URL

tel

http://www.intesis.com

[email protected]m

+34 938047134

5 / 5

Dimensions

External dimensions

Free space recommended in the install location of the device, with spacing enough for external connections.

AC mains

power

DALI port

159 mm

105 mm

58 mm

Ethernet port

Serial console

port

167 mm

130 mm

100 mm

Inhaltsverzeichnis

Andere IntesisBox Server Handbücher

IntesisBox

IntesisBox Modbus Server-Cerberus ISO1745 Bedienungsanleitung

IntesisBox

IntesisBox IBMBSMEB0100000 Bedienungsanleitung

IntesisBox

IntesisBox Modbus Server-DALI Bedienungsanleitung

IntesisBox

IntesisBox BACnet/IP Server-Modbus RTU master Bedienungsanleitung

IntesisBox

IntesisBox BACnet/IP Server-SUNWAYS Bedienungsanleitung

IntesisBox

IntesisBox BACnet/IP Server-Notifier ID3000 Bedienungsanleitung

IntesisBox

IntesisBox ASCII Server-KNX Bedienungsanleitung

IntesisBox

IntesisBox IBBACMEB0100000 Bedienungsanleitung

IntesisBox

IntesisBox Modbus Server-FIDELIO TCP/IP Bedienungsanleitung

IntesisBox

IntesisBox IBOX-ASCII-KNX Bedienungsanleitung

IntesisBox

IntesisBox IBOX-ASCII-BAC-A Bedienungsanleitung

IntesisBox

IntesisBox BACnet/IP Server–Modbus TCP master Bedienungsanleitung

IntesisBox

IntesisBox Modbus TCP Server-Modbus RTU Master Bedienungsanleitung

IntesisBox

IntesisBox Modbus Server-AlgoRex Bedienungsanleitung

IntesisBox

IntesisBox IBOX-MBS-TCP2RTU Bedienungsanleitung

IntesisBox

IntesisBox BACnet/IP Server-LON Bedienungsanleitung

IntesisBox

IntesisBox Modbus Server-FC330A Bedienungsanleitung

IntesisBox

IntesisBox IBOX-ASCII-KNX Bedienungsanleitung

IntesisBox

IntesisBox MH-RC-BAC-1 Bedienungsanleitung

IntesisBox

IntesisBox KNX TP-1 (EIB) Bedienungsanleitung

IntesisBox

IntesisBox BACnet/IP Server-FIDELIO TCP/IP Bedienungsanleitung

IntesisBox

IntesisBox Modbus Server-Galaxy EIA232 Bedienungsanleitung

IntesisBox

IntesisBox IBMBSKNX1000000 Bedienungsanleitung

IntesisBox

IntesisBox ASCII Server-LON Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung