Invacare Rea Bellis Bedienungsanleitung

Rea Bellis

assembly instructions

accessories

English

2REA BELLIS

REA BELLIS

Contents

16"-transportwheel 4

Fitting a one-arm brake 4

Foot brake (only for 16” wheels, seat height 47 cm) 5

Fit an adjustable backrest 6

Adapt to electrically operated seat tilt and backrest tilt adjustments. 8

Fitting the battery 10

Neckrest/headrest 11

Fitting detachable trunk supports 12

Fitting trunk supports 13

Safety belt 14

Height adjustment of height-adjustable armrests 14

Height adjustment of flip-up armrests or hemiplegic armrests 14

Remove the push bar and fit a push handle bar 15

Comfort backrest pad "Laguna" 16

Central legrest 17

Fitting heel straps to the foot plate 18

Fitting heel straps to the foot plate extension 18

Fitting the foot plate extension 19

Reflectors on the rear and sides of chairs with 20”-24” wheels 19

Reflectors on the rear and sides of chairs with 16” wheels 19

Pommel 20

Ta b le tray 21

Crutch holder 22

Incontinence cover 22

4REA BELLIS

1. Start by ﬁtting transport plate (A). Unscrew the

screws on the drive wheel plate. The transport

plate is screwed securely into the same holes

and with the same screws as the drive wheel

plate.

The transport wheel is then attached by inserting

the axle (C) into the transport plate (A) with

spacers (E) on both sides. The axle is attached

securely with nut (F).The lock pin (G) is attached

securely with washer (H) and screw (I). Lock

spacer (J) is placed between the drive wheel plate

and attachment plate (K).

2. In order to ﬁt the push handle,you hold handle (L)

on the underside of the push handle/push bar and

clamp (M) on the upper side. Then attach these

together securely using the screws (N).

Start by removing the standard rear wheel brake.

Attach the one-arm brake to the suitable side of

the chair by tightening screw (A) in the existing

square nut (B).

Adjust the braking effect when necessary by tightening/

loosening the wire (C).Attach the wire to a suitable

point on the underside of the chair using cable ties

to keep it out of the way.

Tools: 5 mm Allen Key

19 mm fixed spanner

Tools: 5 mm Allen Key

16” transport wheel

Fitting a one-arm brake

REA BELLIS

IJK

BCD

HIJK

4. 3. Press down the foot brake tube with your foot

to apply the brake.

4. Push the foot brake tube upwards with your foot

to release the brake.

1. Fit screw (G) into mounting plate (F) and nut

(E).Then ﬁt link bushing (K) into the hole on the

inside of mounting plate (F). Fit link washer (I)

into the hole on the outer side of mounting plate

(F).Tighten using screw (H) through the bushings

to brake tube (A).

Fit nut (E) in the required position on transport

wheel plate (B). Sleeve (J) is to be ﬁtted into the

hole on the mounting plate and everything is to be

securely locked into place on the transport wheel

plate using nut (D) and washer (E).

2. Fit nut (B) onto eye bolt (D). Fit eye bolt (D)

to the brake arm on the transport wheel using

screw (E). Fit washer (C) between eye bolt (D)

and the brake arm and tighten nut (A). Then ﬁt

fork link (G) onto eye bolt (D). Press axle (L)

securely onto the transport wheel through the

mounting plate. Lock into place using washer

(H) and screw (I).Tighten with nut (A). Lock the

wheel into position with washer (J) and nut (K).

Turn the fork link upwards and lock it into place

onto the brake tube with lock clip (F). Follow the

same procedure for the other side.

It is easiest to adjust the brake if you turn the

wheelchair upside down.

1. Loosen nut (B).

2. Loosen lock clip (F) and pull it out.

3. Turn fork link (G) outwards to adjust the

braking effect.

4. Lock fork link (G) into place with lock clip (F)

and tighten nut (B).

5. Adjust fork link (G) by an equal amount on

both sides.

6. Test to check that the braking effect is even,by

spinning both wheels and braking. Both

wheels should now be braked simultaneously.

7. Turn over the chair so that the wheels are on

the ground, and then test the brakes.

8. If additional adjustment is necessary, repeat

steps 1-5.

Tools: 4 mm Allen Key

5 mm Allen Key

7mm fixed spanner

10 mm fixed spanner

19 mm fixed spanner

19 mm box spanner

Foot brake (only for

16” wheels, seat height 47 cm)

6REA BELLIS

1. Start by removing the push bar or the push

handle bar.Then remove the existing backrest by

loosening both of the lower screws (A).

2. Fit the new adjustable backrest and tighten the

screws (A).

3. The height of the backrest can be adjusted using

the four screws (B).

Tools: 5 mm Allen Key

Fit an adjustable backrest

REA BELLIS

4. Adjust the backrest to the shape that you require

using the Velcro straps.

5. Fold the backrest cover over the backrest and

secure it into place as shown in the diagram.The

cover can be folded upwards at the bottom if

necessary (see the enlarged detail in the diagram),

depending on how low the backrest is placed

on the wheelchair.

8REA BELLIS

1. Start by loosening both of the tilt adjustment

handles with their attachments on the push bar.

2. Release the backrest with the pin on the back of

the backrest tilt piston. Loosen this piston from

its attachment under the seat by removing the

circlips (A) and the dowel (B).

3. Then remove the protective casing of the seat

tilt piston by loosening the clips on both sides.

Tools: 2,5 mm Allen Key

screwdriver

Tools: Ciclip pliers

Adapt to electrically operated

seat tilt and backrest tilt adjustment

REA BELLIS

4. Remove the frontal seat tilt piston by loosening

the circlips (A) and removing the dowel (B), the

spacers (C) and then loosening the circlips (D),

removing the dowel (E) and loosening the piston

from its attachment at the rear of the chair.

NB! There is a major risk of you or the user

sustaining trapping injuries when the seat

tilt piston has been removed.

5. Fit the electrically operated seat tilt piston there

instead, using the same circlips and dowels as

when you removed the seat tilt piston.

Note that the frontal piston is to be ﬁtted into

the upper hole of the attachment. If it is difﬁcult

to feed the dowel into place, you must enlarge

the hole on the attachment slightly by removing

paint.

6. Fit the electrically operated backrest tilt piston

into its attachment under the seat with the circlips

(A) and the dowel (B). Attach the piston to the

backrest arch using the pin at the back.

Ensure that it "clicks" into the attachment

securely.

Tools: Circlip pliers

10 REA BELLIS

1. To ﬁ t the battery under the seat, the existing

screw (A) and nut (B), which are by the rear

wheel plate, are to be used.The existing washer

details have been ﬁtted, the battery must also be

attached around the cross tube using the screw

(D), spacer (E) and nut (F).

2. Connect the cables from the seat tilt piston (A),

the backrest tilt piston (B) and the control box

at suitable points under the chair using cable ties,

to keep them out of the way

A = Seat

B = Backrest

FITTINGTHE BATTERY

Tools: 5 mm Allen key

10 mm fixed spanner

17 mm fixed spanner

Andere Handbücher für rea Bellis

Inhaltsverzeichnis

Andere Invacare Rollstuhl Handbücher

Invacare

Invacare Arrow Bedienungsanleitung

Invacare

Invacare STORM Bedienungsanleitung

Invacare

Invacare Compass XE Handbuch

Invacare

Invacare TDX SP2 series Bedienungsanleitung

Invacare

Invacare 65900 Montageanleitung

Invacare

Invacare TDX 4 Handbuch

Invacare

Invacare rea clematis Bedienungsanleitung

Invacare

Invacare Nutron R32 Bedienungsanleitung

Invacare

Invacare P9000 XDT Handbuch

Invacare

Invacare FDX Bedienungsanleitung

Invacare

Invacare Mirage Bedienungsanleitung

Invacare

Invacare At'm Bedienungsanleitung

Invacare

Invacare Pronto M91 Bedienungsanleitung

Invacare

Invacare AVIVA Storm RX Bedienungsanleitung

Invacare

Invacare Rea Clematis Pro Bedienungsanleitung

Invacare

Invacare Spectra Plus Bedienungsanleitung

Invacare

Invacare Power Wheel Chair M71 Bedienungsanleitung

Invacare

Invacare Kompas Montage- und Bedienungsanleitung

Invacare

Invacare Nutron R50LX Bedienungsanleitung

Invacare

Invacare rea azalea assist Bedienungsanleitung

Invacare

Invacare Tracer SX5 Recliner Bedienungsanleitung

Invacare

Invacare Pronto M50 Bedienungsanleitung

Invacare

Invacare Formula CG Seating Bedienungsanleitung

Invacare

Invacare Nutron R32 LX Bedienungsanleitung

Beliebte Rollstuhl Handbücher anderer Marken

Otto Bock

Otto Bock Skippi plus Bedienungsanleitung

SORG

SORG LoopSORG 802 Bedienungsanleitung

Designability

Designability WizzyBug Montageanleitung

Vermeiren

Vermeiren RAPIDO Bedienungsanleitung

Excel

Excel G5 KIDS 0285 Bedienungsanleitung

M. Bartels

M. Bartels SA-3 Bedienungsanleitung

Vermeiren

Vermeiren Turios Bedienungsanleitung

nino robotics

nino robotics NIno Bedienungsanleitung

Nova

Nova TKW-12 Bedienungsanleitung

BCW

BCW Advantage Bedienungsanleitung

You-Q

You-Q Luca Bedienungsanleitung

interco

interco Ortolight Standard Bedienungsanleitung

Nova

Nova 7190L Bedienungsanleitung

Vermeiren

Vermeiren EZ1 Bedienungsanleitung

PaceSaver

PaceSaver Scout M-300 Bedienungsanleitung

Drive Medical

Drive Medical Silver Sport SSP218DDA-SF Bedienungsanleitung

Rehadapt

Rehadapt Light 3D Bedienungsanleitung

Excel

Excel Mobil Bedienungsanleitung

Invacare rea Bellis Bedienungsanleitung

Beliebte Rollstuhl Handbücher anderer Marken