INVENTOR L4VO32-18 Bedienungsanleitung

• USER’S MANUAL

• ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ

• MANUAL UTILIZATORULUI

MODELS:

L4VI32-12/L4VO32-12

L4VI32-09/L4VO32-09

L4VI32-16/L4VO32-16

L4VI32-18/L4VO32-18

L4VI32-24/L4VO32-24

Preface

For correct installation and operation, please read all instructions carefully. Before

reading the instructions, please be aware of the following items:

(1) For the safe operation of this unit, please read and follow the instructions

carefully.

(2) During operation, total capacity of indoor units should not exceed the total

capacity of outdoor units. Otherwise, poor effect of cooling or heating may result.

(3) Direct operators or maintainers should well keep this manual.

(4) If this unit fails to operate normally, please contact our service center as soon

as possible and provide the following information:

● Content on the nameplate(model number, cooling capacity, production code,

ex-factory date).

● Malfunction details(before and after the malfunction occurs).

(5) Each unit has been strictly tested and proved to be qualified before ex-factory.

In order to prevent units from being damaged or operating normally because of

improper disassembly, please do not disassemble the unit by yourself. If you need to

disassemble and check units, please contact our service center. We will send

specialists to guide the disassembly.

(6) All graphics in this manual is only for your reference. For sales or production

reasons, these graphics are subject to change by manufacturer without prior notice.

Contents

1 Remote Controller

···························································1

1.1 Button name and function introduction ·································1

1.2 Preparation before operation ·············································2

1.3 Introduction of operation function

········································2

1.4 Introduction of special functions ·········································6

1.5 Replacing batteries in remote controller and notes

··················7

User’s Manual of Remote Controller

1 Remote Controller YAP1F

1.1 Button name andfunction introduction

User’s Manual of Remote Controller

No.

Button name

Function

ON/OFF

Turn on or turn off the unit

TURBO

Set turbo function

MODE

Set operation mode

Set up&down swing status

I FEEL

Set I FEEL function

TEMP

Switch temperature displaying type on the unit’s display

Set health function and air function

LIGHT

Set light function

X-FAN

Set X-FAN function

SLEEP

Set sleep function

CLOCK

Set clock of the system

TOFF

Set timer off function

TON

Set timer on function

Set left&right swing status

FAN

Set fan speed

Set temperature and time

1.2 Preparation before operation

When using the remote controller for the first time or after replacing the batteries,

please set the time of the system according to current time in the following steps:

(1). Pressing CLOCK button, is blinking.

(2). Pressing or button, the clock time will increase or decrease rapidly.

(3). Press CLOCK button again to confirm the time and return to display current

time.

1.3 Introduction of operation function

(1). Selecting operation mode

In unit on status, press MODE button to select operation mode in following

sequence:

User’s Manual of Remote Controller

(2). Setting temperature

In unit on status, press button to increase setting temperature and press

button to decrease setting temperature. The range of temperature is from 16℃to 30℃.

Note: Under auto mode, manual adjustment of temperature is not needed.

(3). Adjusting fan speed

In unit on status, press FAN button to adjust fan speed in following sequence:

Notes:

①.When operation mode changes, fan speed is memoried;

②.Under dry mode, fan speed is low and can not be adjusted.

(4). Setting swing function

Setting left&right swing

1). Under simple swing status, press button to adjust left&right swing

status;

2). Under fixed-angle swing status, press button to adjust left&right swing

angle circularly as below:

Note: operate continuously left&right swing in 2 seconds, swing states will change

according to above-mentioned order, or switch closed state and state.

Setting up&down swing

1). Under simple swing status, press button to adjust up&down swing

status;

2). Under fixed-angle swing status, press button to adjust up&down swing

angle circularly as below:

Note: operate continuously left&right swing in 2 seconds, swing states will change

according to above-mentioned order, or switch closed state and state;

User’s Manual of Remote Controller

(5). Setting turbo function

Under cool or heat mode, press TURBO button to set turbo function.

When is displayed, turbo function is on.

When is not displayed, turbo function is off.

When turbo function is on, the unit operates in super high speed to achieve quick

cooling or heating. When turbo function is off, the unit operates in setting fan speed.

(6). Setting light function

The light on the receiver light board will display present operation status. If you

want to turn off the light, please press LIGHT button. Press this button again to turn on

the light.

(7). Viewing ambient temperature

In unit on status, receiver light board or wired controller is defaulted to display

setting temperature. Press TEMP button to view indoor or outdoor ambient

temperature.

When is displayed, it means the displayed temperature is setting temperature.

When is displayed, it means the displayed temperature is indoor ambient

temperature.

When is displayed, it means the displayed temperature is outdoor ambient

temperature.

Note: setting temperature is always displayed in Remote Controller.

(8). Setting X-FAN function

In cool or dry mode, press X-FAN button to set X-FAN function.

When is displayed, X-FAN function is on.

When is not displayed, X-FAN function is off.

When X-FAN function is on, the water on the evaporator will be blown away until

turning off the unit to avoid mildew.

(9). Setting health function

In unit on status, press button to set health function.

When is displayed, health function is on.

When is not displayed, health function is off.

Health function is available when the unit is equipped with anion generator. When

health function is on, the anion generator will start operation, adsorbing the dusts and

User’s Manual of Remote Controller

killing the bacteria in the room.

(10). Setting air function

Press button until is displayed, then air function is turned on.

Press button until is disappeared, then air function is turned off.

When the indoor unit is connected with fresh air valve, air function setting can

control the connection of fresh air valve, which can control the fresh air volume and

improve the air quality inside the room.

(11). Setting sleep function

In unit on status, press SLEEP button to turn on or turn off sleep function.

When is displayed, sleep function is on.

When is not displayed, sleep function is off.

Notes:

①.Sleep function can not be set in auto and fan mode;

②.When turning off the unit or switching mode, sleep function is cancelled;

(12). Setting I FEEL function

In unit on status, press I FEEL button to turn on or turn off I FEEL function.

When is displayed, I FEEL function is on.

When is not displayed, I FEEL function is off.

When I FEEL function is turned on, the unit will adjust temperature according to the

temperature detected by the remote controller to achieve the best air-conditioning

effect. In this case, you should place the remote controller within the valid receiving

range.

(13). Setting timer

You can set the operation time of unit as you need. You can also set timer on and

timer off in combination.

Before setting, check if the time of the system is the same as the current time. If not,

please set the time according to current time.

1). Setting timer off

①.Pressing TOFF button, “OFF” is blinking and time displaying zone displays the

timer time of last setting.

②.Press or button to adjust the timer time.

③.Press TOFF button again to confirm setting. OFF is displayed and time

displaying zone resumes to display current time.

User’s Manual of Remote Controller

④.Press TOFF button again to cancel timer and OFF is not displayed.

2). Setting timer on

①.Pressing TON button, “ON” is blinking and time displaying zone displays the

timer time of last setting.

②.Press or button to adjust the timer time.

③.Press TON button again to confirm setting. ON is displayed and time

displaying zone resumes to display current time.

④.Press TON button again to cancel timer and ON is not displayed.

1.4 Introduction of special functions

(1). Setting child lock

Press and button simultaneously to lock the buttons on remote controller

and is displayed.

Press and button simultaneously again to unlock the buttons on remote

controller and is not displayed.

If the buttons are locked, blinks 3 times when pressing the button and any

operation on the button is invalid.

(2). Switching temperature scale

In unit off status, press MODE button and button simultaneously to switch

temperature scale between ℃and ℉.

(3). Setting energy-saving function

In unit on status and under cool mode, press CLOCK and TEMP button

simultaneously to enter energy-saving mode.

When is displayed, energy-saving function is on.

When is not displayed, energy-saving function is off.

If you want to turn off the energy-saving function, press CLOCK and TEMP button

and is not displayed.

Note: energy-saving function is only available in cooling mode and it will be exited

when switching mode or setting sleep function.

(4). Absence function

In unit on status and under heat mode, press CLOCK and TEMP button

simultaneously to enter absence function. Temperature displaying zone displays 8 and

is displayed.

Press CLOCK and TEMP button simultaneously again to exit absence function.

Temperature displaying zone resumes previous display and is not displayed.

User’s Manual of Remote Controller

In winter, absence function can keep the indoor ambient temperature above 0℃to

avoid freezing.

Note: Absence function is only available in heating mode and it will be exited when

switching mode or setting sleep function.

1.5 Replacing batteries in remote controller and notes

(1). Lift the cover along the direction of arrow (as shown in Fig 1①).

(2). Take out the original batteries (as shown in Fig 1②).

(3). Place two 7# (AAA 1.5V) dry batteries, and make sure the position of “+” polar

and “-” polar is correct (as shown in Fig 2③).

(4). Reinstall the cover (as shown in Fig 2④).

Fig.1 Fig.2

Notes:

①.The remote controller should be placed 1m away from the TV set or stereo

sound sets.

②.The operation of remote controller should be performed within its receiving

range.

③.If you need to control the main unit, please point the remote controller at the

signal receiving window of the main unit to improve the receiving sensibility of

main unit.

④.When the remote controller is sending signal, “ ” icon will be blinking for 1

second. When the main unit receives valid remote control signal, it will give

out a sound.

⑤.If the remote controller does not operate normally, please take the batteries

out and reinsert them after 30 seconds. If it still can't operate properly, replace

the batteries.

⑥.When replacing the batteries, do not use old or different types of batteries,

otherwise, it may cause malfunction.

⑦.When you won’t use the remote controller for a long time, please take out the

batteries.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere INVENTOR Klimaanlage Handbücher

INVENTOR

INVENTOR V3MCI-50 Bedienungsanleitung

INVENTOR

INVENTOR WF-60A1 Leitfaden

INVENTOR

INVENTOR O3MVO32-12 Bedienungsanleitung

INVENTOR

INVENTOR V1MFI-66B Bedienungsanleitung

INVENTOR

INVENTOR P9VI32-09WF Bedienungsanleitung

INVENTOR

INVENTOR U4MRS-12 Bedienungsanleitung

INVENTOR

INVENTOR ARCMI-12 Bedienungsanleitung

INVENTOR

INVENTOR AR1MVI-09WFR/AR1MVO-09 Bedienungsanleitung

INVENTOR

INVENTOR RFI-30 Bedienungsanleitung

INVENTOR

INVENTOR V4MDI-12B Bedienungsanleitung

INVENTOR

INVENTOR AR2MVI32-12WiFi Bedienungsanleitung

INVENTOR

INVENTOR DR2VI32-09WFI Bedienungsanleitung

INVENTOR

INVENTOR A2VI-09 Bedienungsanleitung

INVENTOR

INVENTOR H3TBI-100 Bedienungsanleitung

INVENTOR

INVENTOR V4MRFI-24 Bedienungsanleitung

INVENTOR

INVENTOR PR1VI32-09WFC Bedienungsanleitung

INVENTOR

INVENTOR DRVI32-09WF Betriebsanleitung

INVENTOR

INVENTOR LDVI-09WFI/LDVO-09 Leitfaden

INVENTOR

INVENTOR LV4MDI-07 Leitfaden

INVENTOR

INVENTOR CR2VI32-18WFI/CR2VO32-18 Bedienungsanleitung

INVENTOR

INVENTOR CRVI32-09WFC Bedienungsanleitung

INVENTOR

INVENTOR U4MRSL(2)-14 Bedienungsanleitung

INVENTOR

INVENTOR P9VI32-12WF Bedienungsanleitung

INVENTOR

INVENTOR V4MDI-12/U4MRS-12 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung