InWin IW-PLG Tower Bedienungsanleitung
User Manual
IW-PLG Tower
IW-PLG Tower
Table of
Contents
PREFACE 2
SAFETY INFORMATION 2
CAUTION 4
SPECIFICATIONS 5
PRODUCT DIMENSIONS 6
12Gb/s BACKPLANE SPECIFICATIONS 6
Product Introduction 7
7
Box Contents
8
Accessories Box
9
General Information
10
Front Panel Controls and Indicators
11
Rear Panel Configuration
Hardware Installation 12
12
Motherboard Installation
12
Connecting LED Cable, Front Control Panel and Front USB I/O Ports
12
Expansion Card Installation
12
Hard Drive Installation
13
Fan Installation
14
Power Supply Installation
16
Slide Rail Installation
Backplane Introduction 17
Compatibility Lists 17
Q&A 18
Technical Support 19
2
PREFACE
SAFETY INFORMATION
2
To ensure a safe and smooth operation of your InWin IW-PLG Tower, it is essential that you choose
an appropriate location for the system, provide an appropriate operating environment and supply
an adequate amount of power for all components of the system. As you plan for installation, follow
the guidelines below to ensure that the system and its environment are safely and appropriately
positioned for efficient operation and service. Your system should be installed and serviced only by
a qualified technician.
User Manual
Thank you for choosing the InWin IW-PLG Tower. This manual is written for system technicians
who are responsible for installation, troubleshooting, managing and repairing this server chassis.
This document provides an overview of all the features of the chassis, a list of accessories or other
components you may need to finish the installation, troubleshooting methods and instructions on
adding and removing components in the InWin IW-PLG Tower. For the latest version of this manual,
you may visit InWin’s server website.
Home
Environment Selection: The system is designed to operate in a typical office environment:
• The location should be clean, dry and free of airborne particles.
•It should be placed in a well-ventilated room, and away from sources of heat including direct sunlight
and radiators.
• It should be kept away from sources of vibration or physical shock.
• The space should be accommodated with a properly grounded wall outlet, and with sufficient space
to access the power supply cords.
• The operating environment temperature should be around 0°C to 40°C (32°F to 104°F).
Heed Safety Instructions: Before working with InWin IPC/storage server products, we strongly
recommend you use this guide as a reference and follow the safety instructions. The instructions in this
manual will help you ensure and maintain compliance with existing product certifications and approvals.
Follow the described, regulated components mentioned in this manual. Use of non-UL listing products
or other regulators may not comply with product regulations in the region(s) in which the product is
sold.
Hazardous Conditions, Devices and Cables: Hazardous electrical conditions can be present on/in
power supply units and their cables. Disconnect the power cord and any other devices attached to the
server before opening the case. Failing to follow safety procedures will increase the risk of personal
injury or equipment damage.
System Power On/Off: The power button DOES NOT totally turn off the system AC power. To remove
the power of the system, you must unplug the AC power cord from the outlet or the system’s power
supply units. Make sure the power cord is unplugged before you open the chassis, add or remove any
components.
3
IW-PLG Tower
Home
4
4
To avoid damage and maintain your safety, please read the following terms listed below:
Installing or Re moving Jumpers: A jumper is a short length conductor used to close, open or bypass
part of an electronic circuit. Jumpers on InWin backplanes have a small tab on top that you can pick
up with your fingertips. Grip the jumper carefully and plug the jumper to cover the jumper pins on the
backplane. Once you need to remove the jumper, grip the jumper and carefully pull without squeezing.
Electrostatic Discharge (ESD) and ESD Protection: In most cases, ESD may damage disk drives,
electronic boards and other parts. We recommend that you conduct installation only at an ESD free
space. If not possible, perform ESD protection protocol by wearing anti-static wrist straps attached to
the ground on any unpainted metal surface on your server during operation.
CAUTION
Do not populate hard drives and turn on the power until the system has stabilized. Make
sure hard drives and other components are properly connected before turning on the
system.
Tighten or loosen all screws with a screwdriver.
Apply the correct screws packed in the accessories box.
For your safety, please have at least two people lift and install the unit in its
designated area.
Before mounting the unit to the cabinet, make sure the rail is installed correctly.
When installing and removing any module or part, please use the handles.
1
2
3
4
5
6
User Manual
Home
5
IW-PLG Tower
Home
SPECIFICATIONS
Model Name IW-PLG Tower
Industry Standard EIA-RS310D
M/B Form Factor ATX (12" x 9.6"), CEB (12" x 10.5"), EEB (12" x 13")
Drive Bay • External 2.5"/3.5" hot-swap trays x 12 (pre-installed x 8), 5.25" x 1
• Internal 2.5" x 2 or 3.5" x 1
Power Supply
Supports:
•Form factor: 80 Plus Platinum CRPS with PDB cable management
• Watt: 800W/1200W/1600W(200-240V)
Indicator Power status, HDD LED, LAN1/LAN2/LAN3/LAN4 LED, ID LED, system
fail activity LED
Front Control Panel Power switch, ID switch, system reset, NMI, USB 3.0 x 2
Backplane Mini-SAS (SFF-8643), 12Gb/s supported x 3 (pre-installed x 2)
Cooling Fan •Middle: 92 x 25mm PWM fans x 3
•Rear: 120 x 25mm PWM fan x 1
Expansion Slot Full-height PCIe slots x 9
Material •Material: SGCC
•Thickness: 1.0mm
Rail Kit Supports 28" tool-less & ball-bearing slide rail
Product Dimensions
(DxWxH; Chassis Only)
589.7 x 200 x 430mm
(23.22" x 7.87" x 16.93")
Package Dimensions
(DxWxH) 860 x 610 x 360mm
Weight Net weight: 16.95kg
Gross weight: 21.28kg
Cubic Feet 6.67
Container Information
Single packing with pallets:
•20': 100pcs
•40': 220pcsw
• 40' HQ: 264pcs
The actual product is subject to change without prior notice. InWin Development Inc. reserves the
right to make any final modifications.
The adjacent image is for reference only. All hardware components and optional parts are not included.
•
•
9
IW-PLG Tower
Home
When you open the side cover, it should reflect the diagram’s image.
General Information
1
No Item No Item No Item
1 PSU mounting area 4 2.5" x 2 or 3.5" x 1 7 Foot stands
2 MB mounting area 5 120 x 25mm PWM rear fan x 1 8 92 x 25mm PWM middle fan x 3
3 GPU holder 6 Full-height PCIe slot x 9 9 Front panel with lock
No Item
10 2.5"/3.5" hot-swap tray x 12
(pre-installed x 8)
11 5.25" x 1
12 Side panel lock
13 Indicator & front control panel
7
6
4 9
8
5
2 3
5
6
7
1 4
8
1313
1212
1111
1010
Inhaltsverzeichnis
Andere InWin Server Handbücher
InWin
InWin IW-RN212-04 Bedienungsanleitung
InWin
InWin IW-RS112-08 Bedienungsanleitung
InWin
InWin IW-RN424-04 Bedienungsanleitung
InWin
InWin IW-RS208-07 Bedienungsanleitung
InWin
InWin IW-RN316-04 Bedienungsanleitung
InWin
InWin IW-RS208-04 Bedienungsanleitung
InWin
InWin IW-RS216-07 Bedienungsanleitung
InWin
InWin IW-RS212-04 Bedienungsanleitung
InWin
InWin IW-RS448-05 Bedienungsanleitung
InWin
InWin Cobra IW-RS316-07 Bedienungsanleitung
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung