ION Shawcity ARA DOCK4 Bedienungsanleitung

Pioneering Gas Sensing Technology.

ionscience.com Part No: 908225 V1.0

Power

The ION ARA DOCK4 bump test and calibration station has two power sources. A 12V DC

mains power supply and an internal rechargeable battery.

The internal rechargeable battery provides approximately 5 hours of continuous

operation when fully charged (based on 4 x ARA’s inserted).

The ION ARA DOCK4 will automatically switch itself o between tests if inactive for

2 minutes. This can be adjusted via ION ARA Dock4Manager software.

The power LED is green when it has sucient charge or connected to mains power.

Setup and Installation

1. Loosen the lid cover bolts with a 3mm hexagonal wrench and open the lid to gain

access to the calibration gas compartment.

2. Insert the calibration gas into the housing and screw clockwise until seated.

Secure the cylinder with the bottle strap. Close the lid and fasten the cover bolts.

3. The calibration pressure gauge will indicate the amount of gas available.

4. Press the power button. The ION ARA DOCK4 bump test and calibration station is now

ready to use.

NOTE: These can be adjusted via ION ARA DOCK4 Manager and IR Link

Battery low Normal operation No USB

Default Gas Concentrations

The recommended default calibration gas concentrations are below:

ION ARA Models: Gas Type: Gas Concentrations:

ARA100, ARA100H Hydrogen Sulﬁde (H2S) 25 ppm

ARA200, ARA200H Carbon Monoxide (CO) 100 ppm

ARA300 Oxygen (O2) 18% Vol

ARA400 Sulfur Dioxide (SO2) 10 ppm

Power Button and Status Colours

Powers up the ION ARA DOCK4 bump test and calibration station.

ARA DOCK4 Bump Test &

Calibration Station

Quick start guide

ARA DOCK4 Bump Test &

Calibration Station

Quick start guide

Pioneering Gas Sensing Technology.

ionscience.com Part No: 908225 V1.0

Operation

1. Firmly place between 1 and 4 ION ARA single gas detectors face-down into the

bays.

2. To conduct a bump test, press the blue button labelled ‘bump test’. The bay LED

status will illuminate amber during the test. Upon completion, the bay LED will

indicate green if passed and red if failed.

3. To conduct a calibration, press the green button labelled ‘calibration’. The bay LED

status will illuminate amber during the test. Upon completion, the bay LED will

indicate green if passed and red if failed.

Brieﬂy applies gas to test the sensor response, downloads logged events

and tests the audible and visual alarms

Adjusts the sensor settings to match the gas applied, downloads logged

events and test the audible and visual alarms

Troubleshooting

• Check the built-in pressure gauge to ensure there is sucient calibration gas

(34L & 57L are full at 500psi). Inspect the ARA inlet port. Clear any obstructions and

replace clogged or dirty ﬁlters.

• Clean ARA IR communication window with a non-alcohol-based cleaner.

• Bright sources of light may interfere with the ION ARA DOCK4 IR communication ports,

try relocating.

Test passed

Test in progress

Test failed

ARA Status LEDs

NOTE: The gas is only supplied to the bays where a detector is present.

If you are still expeiencing problems after troubleshooting, please email

technical.support@ionscience.com or call 01763 208 503.

Andere Handbücher für shawcity ARA DOCK4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ION Gaswarngerät Handbücher

ION

ION TVOC 2 Bedienungsanleitung

ION

ION SF6 LEAKMATE Bedienungsanleitung

ION

ION ARA H2S-H Bedienungsanleitung

ION

ION GasCheck Tesla Bedienungsanleitung

ION

ION FALCO Bedienungsanleitung

ION

ION ARA Series Bedienungsanleitung

ION

ION GasClam Bedienungsanleitung

ION

ION SF6 P2 Bedienungsanleitung

ION

ION Panther Bedienungsanleitung

ION

ION TIGER LT Bedienungsanleitung

ION

ION GasCheck G Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung

ION shawcity ARA DOCK4 Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken