ION Total PA Live Bedienungsanleitung

TOTAL PA™LIVE

Quickstart Guide English ( 3 – 11 )

Guía del usuario Español ( 12 – 21 )

Guide d’utilisation Français ( 22 – 31 )

Appendix English ( 32 )

User Guide (English)

Introduction

Thank you for purchasing the Total PA™Live. At ION, your entertainment is as important to

us as it is to you. That’s why we design our products with one thing in mind—to make

your life more fun and more convenient.

Box Contents

Total PA™Live

Power Cable (5 ft. / 150 cm)

Microphone with cable (15 ft. / 450 cm)

Speaker Stand

Quickstart Guide

Support

For the latest information about this product (documentation, technical specifications,

system requirements, compatibility information, etc.) and product registration, visit

ionaudio.com.

For additional product support, visit ionaudio.com/support.

Setup

1. Make sure all items listed in the Box Contents are included in the box. Look in the box

under the foam sheet for the power cable and microphone.

2. Read the Safety & Warranty Manual before using the product.

3. Study the Connection Diagram.

4. Make sure all input devices (such as microphones, CD players, or digital media players) are

turned off with their volume settings set to “zero.”

5. Connect all devices as shown in the Connection Diagram.

6. Switch everything on in the following order:

a. Audio input devices (e.g. microphones, instruments, CD players)

b. Total PA™Live

7. When you are finished using Total PA™Live, switch everything off in the following order:

a. Total PA™Live

b. Audio input devices

Connection Diagram

Items not listed under the Box Contents are sold separately.

Microphones

SD Card

(16 GB limit and only

MP3

files supported)

USB drive (16 GB limit and

only MP3

files supported)

Smartphone

Tablet

Power

Smartphone

Features

Rear Panel

1. Media Panel Buttons: Controls for the

USB/SD, FM radio, and Bluetooth®audio

sources. These controls include mode

selection and music playback options. See

Media Panel for more information.

2. USB Port: Connect your USB flash drive

here to play music. You can also use this

port for charging the USB device, such as a

tablet or smartphone. To charge a device

that is streaming music via Bluetooth,

pause the music first and then wait for it to

reconnect after the USB cable (not

included) is inserted.

3. SD Card Slot: Insert your SD card here to

play music.

4. Display: This screen shows information

relevant to Total PA™Live’s current

operation.

Note: The Display comes with a plastic

protector on it. Remove this for optimal

viewing.

5. Mic Inputs (1/4”/6.35 mm & XLR):Connect

a microphone or mic-level source to these

inputs.

6. Aux Inputs (1/8” &XLR): These inputs can

be used to connect a CD player, MP3

player, or other audio source.

7. Mix Out (XLR):Connect this output to a

speaker, mixer, or recorder.

8. Control Knob: Turn this knob to adjust the

main volume (overall output) of the

loudspeaker. Push this knob to select and

make adjustments to the mic 1 volume, the

mic 2 volume, source volume (radio, USB,

SD, Bluetooth signal, and aux input), echo

effect, high EQ, and low EQ. The volume of

Total PA™Live does not affect your

Bluetooth device volume. For the best

sound quality, set your input source volume

to 100% and use the Source and Main

Volume control of the speaker to adjust the

volume.

9. Repeat/Link: In USB or SD mode, press this button to repeat a single track, folder, or

all tracks. Press and hold this button to start stereo linking to another Total PA™Live.

10. Mode: Press this button to select the audio source to use: USB, SD, FM radio, Aux

(available to select when the USB port and SD card slot are empty), or Bluetooth.

MIC IN 2 XLR IN MIX OUTMIC IN 1

PRESETS

LINK

11. Clip LED: The Clip LED will flash red if the signal from the input jacks or Media Panel

audio source is clipping (distortion from an overly loud signal). If this happens,

decrease the setting of the Main Volume knob or the volume for the Aux/Mic Input (if

a loud device is plugged into either).

12. Light Mode Button: Press and hold this button to turn the Party Starter™lights off or

on. Press and release this button to toggle between one of these five modes for the

lights on the front panel.

• Color Cycle: The lights slowly glow and cycle through colors. This is the default

mode when Total PA™Live is first powered on.

• Beat Sync: The lights flash and change colors according to the tempo of the music

playing on the speaker. For the best lighting effect, you may need to adjust the

volume of your device, the source volume, and/or the main volume.

• Color Wheel: The lights rotate in a wheel of all colors.

• Color Beat Sync: The lights rotate in a wheel of all colors and change direction and

speed according to the tempo of the music playing on the speaker. For the best

lighting effect, you may need to adjust the volume of your device, the source

volume, and/or the main volume.

• Off: The lights turn off.

13. Power Cable Input (IEC):Insert the included power cable here to charge the unit.

14. Power Switch: Flip this switch to toggle the speaker’s power on or off. Your previous

settings will be remembered when powering off and on again.

Note: Total PA™Live will power off after 15 minutes with no audio playing.

Media Panel

Use the following buttons on the Media Panel to control the USB/SD, FM Radio, and

Bluetooth audio sources.

Mode: Press this button to switch the audio source between USB/SD, FM radio, Aux

(available to select when the USB port and SD card slot are empty) and Bluetooth. The

default mode when powering on Total PA™Live is Bluetooth. The USB/SD mode is only

selectable if a USB drive or SD card is plugged into Total PA™Live; otherwise, the Mode

button will toggle between Bluetooth, Aux, and FM radio only.

Note: Your USB drive or SD card cannot be more than 16 GB and it must contain playable

files in order for its data to appear properly in the Display. It can have MP3 files. When you

connect a USB drive or SD card with playable files, Total PA™ Live will order the files

alphabetically by folder on the root directory and then by track name in the folder.

Play/Pause: When USB/SD is selected as the audio source, press this button to

play/pause the currently selected track. Double press this button to stop playback and

return to the beginning of the track list.

In Radio mode, press and hold Play/Pause to set a preset. Select which preset number to

set the station to using the <and >buttons and press Play/Pause to confirm. Press and

release Play/Pause when in Radio mode to toggle through the saved radio presets. The

display will show the selected the preset number (P 1-30).

When Bluetooth is selected as the audio source, press this button to play/pause the

currently selected track or press and hold this button to turn voice prompts on/off.

Repeat: Press this button to cycle through the five repeat/shuffle options:

• Play the USB/SD folder’s tracks in order with repeat/shuffle off (OFF).

• Play the tracks in random order (Rd0).

• Play the current USB/SD track on repeat (ONE).

• Play all the tracks on the USB drive or SD card on repeat (ALL).

• Play the current folder’s tracklist on repeat (F0d). The folder used is based on what

song is playing when it is activated. For instance, if a song playing is on the root level,

selecting F0d will repeat only songs at the root level. If a song is in folder “A”, then

only songs in folder “A” will be repeated.

Previous: When USB/SD or Bluetooth is selected as the audio source, press this button to

go to the previous track in the playlist.

Next: When USB/SD or Bluetooth is selected as the audio source, press this button to go

to the next track in the playlist.

Note: In some apps on Bluetooth devices, pressing the <(Previous) or >(Next) buttons

may change the playlist or music genre rather than the track.

Lights: Press to toggle through the light modes: Color Cycle, Color Wheel, Color Wheel

Beat Sync, Beat Sync, Off. Press and hold when the Party Starter™lights are on to turn the

Party Starter™lights off and keep the woofer lights on.

Operation

Using the Control Knob

The Control Knob defaults to controlling the Main Volume for all channels. Press the

Control Knob to toggle through different functions: Mic Channel, Source, Echo effect level,

and EQ.

• Press the Control Knob to select the Mic channel 1 or 2. Rotate the Control Knob to

raise or lower the volume of the Mic input independently of the other channels.

• Press the Control Knob again to select Source. Rotate the Control Knob to raise or

lower the volume of the Aux/BT/USB/Radio signal independently of the Mic channels.

• Press the Control Knob again to control the Echo effect level for the Mic channel.

• Press the Control Knob again to select Low EQ adjustment. Rotate the Control Knob

to raise or lower the low frequencies on all channels.

• Press the Control Knob again to select High EQ adjustment. Rotate the Control Knob

to raise or lower the high frequencies on all channels.

Note: The mid EQ frequencies can change based on use of the app and/or certain

Acoustic Optimization settings, but cannot be controlled on the speaker. Therefore, if the

hi or low EQ is adjustment manually, via the push encoder, the mid EQ should return to 0.

• Press the Control Knob again to return to Main Volume adjustment.

If there is no activity on the Control Knob for 5 seconds, the function will go back to Main

Volume.

Pairing with a Bluetooth Device

1. Power on the Total PA™Live by flipping the on/off switch.

2. Use the Mode button to select Bluetooth mode (unless it is the first power on or Bluetooth mode

was the mode it was in when it was powered down) and Total PA™Live will automatically enter

Bluetooth pairing mode.

3. Total PA™Live will automatically enter Bluetooth pairing mode.

4. Navigate to your device’s Bluetooth setup screen, find Total PA Live, and connect. Do not

connect to Total PA Live_BLE; this is reserved exclusively for connecting to the ION Sound XP™

app. When connected, the Bluetooth icon on the display will flash and you will hear “Connected”.

Note: If you experience trouble in connecting, select “Forget this Device” on your Bluetooth device

and try to connect again.

5. To disconnect, turn off Bluetooth from your device’s Bluetooth settings.

Linking Two Speakers (Stereo-Link™):

1. Power on both Total PA™Live speakers by flipping their on/off switches. Make sure they are in

Bluetooth pairing mode and not connected to a device.

2. Press and hold the Repeat/Link button on one speaker (the primary “Left” speaker which will

control both) to enter Stereo Link mode. Once a link has been established, the word LINK will

appear on both speaker displays.

3. Connect to the primary speaker via Bluetooth.

To disconnect, double press the Repeat/Link button.

Note: The speakers should be within 65.6’ (20 m) of each other to properly link.

Note: Total PA™Live is not compatible with previous ION PA models. To link to a previous model, use

an XLR cable (not included) and link from the newer PA to the previous one via the XLR Out on Total

PA™Live and the XLR Aux In on the previous model.

Once connected, use the Source Volume adjustment to affect the output of BOTH the Primary Speaker

and the Secondary Speaker.

You can also adjust the Main volume, Mic volume, and EQ separately on each speaker. Echo effect

adjustment affects only the mic input on the Primary Speaker. The Secondary Speaker will have no

echo effect.

Pairing a Bluetooth Device Using NFC

NFC (near-field communication) allows data exchange from devices, such as pairing, by gently

bumping them together. Check in your device’s manual to see if this feature is supported.

To use NFC to pair with Total PA™ Live:

1. In order to use NFC, your device must be turned on and unlocked.

2. Enter your device’s Settings menu and check that NFC is turned On (one-time step).

3. Power on Total PA™ Live.

4. Touch and briefly hold your device to the NFC logo located on Total PA™ Live’s top panel.

5. Follow the pairing instructions that appear on your phone. If a passcode is required, enter

“0000”.

To unpair, gently bump your device against the NFC logo.

SD/USB Mode

Press the Mode button to toggle through to select SD or USB mode. Total PA™Live will

automatically play the first compatible file. Files are played in alphabetical order of what is

on the root level, then alphabetical by folder, and then alphabetical by track name. Media

playback will stop when all media has been played on the SD card or USB drive. Press

and hold the Next and Previous buttons to fast forward or rewind within the song.

Note: The SD card or USB drive must have playable files for it to appear on the media

panel’s display. If there is no USB drive or SD card inserted into the media panel, pressing

and releasing the Mode button will toggle through Bluetooth, Aux, and radio.

Repeat settings (abbreviations will show on the display):

• ALL: Repeat all of the tracks in the folder.

• FOLd: Repeat all of the tracks in the folder.

• OnE: Repeat the current playing USB track.

• rAn: Shuffle the track order.

App Control

IMPORTANT: To ensure the best possible experience with the app, use the most

current Android OS or iOS on your device.

Follow these steps to download the free app on your device:

1. Open the Apple App Store or Google Play on your device. Then, search for the ION

Sound XP app.

2. Follow the on-screen instructions to download and install the app. Once

downloaded, the ION Sound XP app will appear on your device's home screen.

3. Connect your device to Total PA™Live via Bluetooth. See the Pairing with a

Bluetooth Device to learn how to do this.

4. Open the ION Sound XPTM app. If prompted, allow the app to access your device's

Bluetooth and Location Services.

5. Tap to select Add A Product on the screen. The app will scan and find Total PA™Live.

If you are having issues connecting, tap Help with setting up? for additional tips.

6. Select the Total PA™Live icon to go to the next screen, where you can use the app to

control various functions of the speaker such as:

• Radio: Play the radio, change stations, and edit presets.

• EQ: Adjust the speaker's equalization.

• Mic Volume: Adjust the volume for the microphone inputs.

• Source Volume: Adjust the volume for Bluetooth, Aux input, and the FM radio.

• Main Volume: Adjust the source volume together.

• Echo Effect: Adjust the amount of echo effect.

• Lighting Effects: Select the lighting effect or turn the lighting effects on/off.

• Voice Prompts: Enable or disable the voice prompts.

• Support: Visit ionaudio.com, contact Technical Support, and view Warranty

information and Frequently Asked Questions.

Andere Handbücher für Total PA Live

Inhaltsverzeichnis

Sprachen:

Andere ION Lautsprechersystem Handbücher

ION

ION TAILGATER BLUETOOTH Bedienungsanleitung

ION

ION ANYROOM Bedienungsanleitung

ION

ION TOTAL PA GLOW 3 Bedienungsanleitung

ION

ION BLOCK ROCKER BLUETOOTH Bedienungsanleitung

ION

ION TOTAL PA PRIME Bedienungsanleitung

ION

ION Game Day Lights Bedienungsanleitung

ION

ION TOTAL PA TITAN Bedienungsanleitung

ION

ION TAILGATER BLUETOOTH Bedienungsanleitung

ION

ION WATER ROCKER Bedienungsanleitung

ION

ION TOTAL PA GLOW Bedienungsanleitung

ION

ION Sport XL Bedienungsanleitung

ION

ION Block Party Live Bedienungsanleitung

ION

ION Offroad Bedienungsanleitung

ION

ION Pro Glo Duo Bedienungsanleitung

ION

ION Mega Party Express Bedienungsanleitung

ION

ION BLOCK PARTY Bedienungsanleitung

ION

ION PROJECT ROCKER Bedienungsanleitung

ION

ION TOTAL PA TITAN Bedienungsanleitung

ION

ION EXPLORER EXTREME Bedienungsanleitung

ION

ION Game Day Lights Bedienungsanleitung

ION

ION BLOCK ROCKER BLUETOOTH Bedienungsanleitung

ION

ION Explorer Outback Bedienungsanleitung

ION

ION Pathfinder Bedienungsanleitung

ION

ION Total PA Premier Bedienungsanleitung

Beliebte Lautsprechersystem Handbücher anderer Marken

JVC

JVC CA-MXK5R Bedienungsanleitung

LG NB4532B Bedienungsanleitung

JVC

JVC CA-FSH100 Bedienungsanleitung

5Core

5Core Pro Series Bedienungsanleitung

EAW

EAW MQV1394e Bedienungsanleitung

Lynx

Lynx GXR-LA10A Bedienungsanleitung

iLive

iLive ITB066B Bedienungsanleitung

RDX

RDX QuickStation 4 Bedienungsanleitung

Electro-Voice

Electro-Voice S-122 Bedienungsanleitung

Sven

Sven SPS-619 GOLD Bedienungsanleitung

Pioneer

Pioneer CS-7070 Bedienungsanleitung

EAW

EAW UB82e Bedienungsanleitung

Sondpex

Sondpex Active Speaker System and Digital Music... Bedienungsanleitung

JVC

JVC NX-PN7 Bedienungsanleitung

Yamaha

Yamaha NX-A01 - Speaker Sys Bedienungsanleitung

SE Audiotechnik

SE Audiotechnik I-LINE Bedienungsanleitung

Gemini

Gemini WRX-843 Series Bedienungsanleitung

TCL

TCL 6100 Series Bedienungsanleitung