IPGARD SDVN-1S-P Bedienungsanleitung

Document ID: USM-0S0-001 Revision: 1.12

Made in U.S.A. www.iPGARD.com 1-800-284-2131

USER MANUAL

Advanced Single Port DVI-I Secure KVM

SDVN-1S-P 1-Port Secure DVI-I KVM with Audio and CAC Support

Release Date: July 3rd, 2018

TABLE OF CONTENTS

TECHNICAL SPECIFICATIONS___________________________________________________________

WHAT’S IN THE BOX?_________________________________________________________________

SECURITY FEATURES_________________________________________________________________

SDVN FRONT AND REAR______________________________________________________________

INSTALLATION_______________________________________________________________________

CAC INSTALLATION: COMMON ACCESS CARD, SMART CARD READER__________________________

CAC PORT CONFIGURATION____________________________________________________________

AUDITING: Dumping the Event Log via User Menu Options___________________________________

RESET: Restore Factory Default_________________________________________________________

LED’s BEHAVIOR_____________________________________________________________________

TROUBLESHOOTING__________________________________________________________________

TECHNICAL SUPPORT_________________________________________________________________

LIMITED WARRANTY STATEMENT_______________________________________________________

Advanced Single Port DVI-I Secure KVM 2

TECHNICAL SPECIFICATIONS

Advanced Single Port DVI-I Secure KVM 3

VIDEO

Format DVI-D Single Link, DVI 1.0

Host Interface (1) DVI-D 23-pin

User Console Interface (1) DVI-I 23-pin

Max Resolution 2560 x 1600 @ 60Hz; 3840x2160 @ 30Hz (w/HDMI-to-DVI adapter)

DDC 5 volts p-p (TTL)

Input Equalization Automatic

Input Cable Length Up to 20 ft.

Output Cable Length Up to 20 ft.

USB

Signal Type USB 1.1 and 1.0 Keyboard and Mouse only. USB 2.0 for CAC connection.

Type A to B (2)

User Console Interface (2) USB Type-A for keyboard and mouse connection only

(1) USB Type-A for CAC connection

AUDIO

Input (1) Connector Stereo 3.5mm Female

Output (1) Connector Stereo 3.5mm Female

POWER

Power Requirements 12V DC, 2A (minimum) power adapter with center-pin positive polarity.

ENVIRONMENT

Operating Temp 32° to 104° F (0° to 40° C)

Storage Temp -4° to 140° F (-20° to 60° C)

Humidity 0-80% RH, non-condensing

CERTIFICATIONS

Security Accreditation Common Criteria Validated To NIAP, Protection Prole PSS Ver. 3.0

OTHER

Emulation USB 1.1 and USB 2.0 Compatible

CONSOLE

INPUT

K/M

Audio DVI-I OUT

CAC

SDVN-1S-P

12VDC2.0A AUDIO

SLPW K/M CAC

DVI-D IN

CONSOLE

INPUT

K/M

Audio DVI-I OUT

CAC

SDVN-1S-P

12VDC2.0A AUDIO

SLPW K/M CAC

DVI-D IN

WHAT’S IN THE BOX?

SECURITY FEATURES

Advanced Single Port DVI-I Secure KVM 4

Anti-Tamper Switches

Each model is equipped with internal Anti-Tamper switches, which sense attempts to open the device

enclosure. Once the system identies such an attempt, all the front panel LED’s will ash rapidly and the

unit will become useless by shutting off connection with all attached PCs and peripherals disabling any

functionality.

Tamper-Evident Seal

The enclosure of the unit is protected with a tamper-evident seal to provide a visual evidence if the unit has

been opened.

Protected Firmware

The controller of the unit has a special protection feature that prevents reprogramming or reading the

rmware.

High Isolation on USB Channels

Opto-isolators are used in the unit to keep USB data paths electrically isolated from each other, providing

high isolation and preventing data leakage between ports.

Secure EDID Emulation

The unit prevents unwanted and unsecure data to be transmitted through the DDC lines by means of

secure EDID learning and emulation.

SDVN Unit 1 port Secure DVI-I KVM

PS12VDC2A 12V DC, 2A (minimum) power adapter with center-pin positive polarity.

User Manual

Figure 4-1: SDVN-1S-P Front panel

Figure 4-2: SDVN-1S-P Rear panel

INSTALLATION

Advanced Single Port DVI-I Secure KVM 5

SYSTEM REQUIREMENTS

Table 5-1

Console Port Authorized Devices

Keyboard

Wired keyboard and keypad without internal USB hub or composite device

functions, unless the connected device has at least one endpoint which is a

keyboard or mouse HID class, KVM/KM extender;

Audio out Analog amplied speakers, Analog headphones, Digital audio appliance.

Mouse/Pointing Device Any wired mouse or trackball without internal USB hub or composite device

functions, Touch-screen, Multi-touch or digitizer, KVM/KM extender.

User Authentication

Device Smart-card reader, PIV/CAC reader, Token or Biometric reader.

1. iPGARD Secure PSS is compatible with standard personal/portable computers, servers or thin-clients,

running operating systems such as Windows or Linux.

2. The peripheral devices that are supported by the KVM are listed in the following table:

SDVN-1S-P

DVI-D IN

AUDIO OUT

DVI-I OUT

USB IN

USB OUT

CAC IN

CAC OUT

AUDIO IN

CONSOLE K/M

Audio DVI-I OUT

CAC

SDVN-1S-P

INSTALLATION

Single-Head Units:

1. Ensure that power is turned off or disconnected from the unit and the computer.

2. Use a DVI cable to connect the DVI output port from the computer to the DVI-I IN port of the

unit.

3. Use a USB cable (Type-A to Type-B) to connect a USB port on the computer to the USB port of

the unit.

4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of the

computer to the AUDIO IN port of the unit.

5. Connect a monitor to the DVI-I OUT console port of the unit using a DVI cable.

6. Connect a USB keyboard and mouse in the two USB console ports.

7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.

8. Optionally connect CAC (COMMON ACCESS CARD, SMART CARD READER) to the CAC port in

the user console interface.

9. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and

then turn on the computer.

Figure 6-1: SDVN-1S-P

Note:

You can connect 1 computer to the single port KVM.

Note:

VGA-to-DVI adapter must be used if video input source is analog. Also, if the monitor connected to

the output is dual-link DVI monitors, then DVI-I cable must be used from the computer.

Advanced Single Port DVI-I Secure KVM 6

IMPORTANT WARNINGS - For security reasons:

• This product does not support wireless devices. Do not attempt to use a wireless keyboard or a

wireless mouse with this product.

• This product does not support keyboards with integrated USB hubs or USB ports. Only use

standard (HID) USB keyboards with this device.

• This product does not support microphone audio input or line input. Do not connect any

microphones or headsets with microphones to this device.

• Connection of authentication devices (CAC) with external power sources is prohibited.

Advanced Single Port DVI-I Secure KVM 7

INSTALLATION (Continued)

EDID Learn:

The KVM is designed to learn the connected monitor’s EDID upon power up. In the event of connecting a

new monitor to the KVM, a power recycle is required.

The KVM will indicate to the user the EDID learn process by ashing the front panel’s LEDs. Port one green

LED will begin to ash for about 10 seconds. When the LED stops ashing, the EDID learn process is done.

The monitor must be connected to the video output connector located in the console space at the back of

the KVM during the EDID learn process.

If the read EDID from the connected monitor is identical to the current stored EDID in the KVM then the

EDID learn function will be skipped.

Advanced Single Port DVI-I Secure KVM 8

CAC (COMMON ACCESS CARD, SMART CARD READER) INSTALLATION

CAC PORT CONFIGURATION

The following steps are intended for the system administrator or IT manager only.

CAC connection to the computer requires a USB cable connection separate from the keyboard and mouse.

This allows the CAC to be connected independently from the keyboard and mouse. It also allows the user to

select whether CAC is supported or not.

1. Ensure that power is turned off or disconnected from the unit and the computer.

2. Use a USB cable (Type-A to Type-B) to connect a USB port on a computer to its respective CAC USB

ports on the KVM. Do not connect the USB cable if CAC functionality is not needed for that computer.

3. Connect a CAC (smart card reader) to the CAC port in the user console interface.

4. Power on the KVM by connecting a 12VDC power supply to the power connector, and then turn on the

computer.

The following steps are intended for the system administrator and operators (users).

Note: Only one computer connected to port 1 is required for this operation

CAC port Conguration is an optional feature, allowing registration of any USB peripheral to operate with

the KVM. Only one peripheral can be registered and only the registered peripheral will operate with the

KVM. By default, when no peripheral is registered, the KVM will operate with any Smart Card Reader.

Congure the CAC Port via User Menu Options

1. Open the Administration and Security Management Program.

2. Using the keyboard, press the Alt key twice and type “cnfg”.

3. At this stage the mouse connected to the KVM/KM will stop functioning.

4. Enter the default username “user” and press Enter.

5. Enter the default password “12345” and press Enter.

6. Select option 2 from the menu on your screen and press Enter.

7. Connect the peripheral device to be registered to the CAC USB port in the console side of the KVM/KM

and wait until the KVM /KM is reading the new peripheral information.

8. The KVM/KM will list the information of the connected peripheral on the screen and buzz 3 times when

registration is completed.

Figure 8-1: User Menu

Advanced Single Port DVI-I Secure KVM 9

AUDITING: Dumping the Event Log via User Menu Options

RESET: Restore Factory Defaults

The following steps are intended for the system administrator.

Note: Only one computer connected to port 1 is required for this operation

The Event Log is a detailed report of critical activities stored in the KVM or KVM memory. A comprehensive

feature list and guidance for Administration and Security Management Tools can be found in the

Administrator’s Guide available for download from: http://ipgard.com/documentation/

To view or dump the Event Log:

1. Open the Administration and Security

Management Program

2. Using the keyboard, press the Alt key twice and

type “cnfg”.

3. Enter the default admin name “admin” and press

Enter.

4. Enter the default password “12345” and press

Enter.

5. Request a Log Dump by selecting option 5 in the

menu. (Shown in Figure 9-1)

* See Administration and Security Management Tool Guidance

for detailed information.

* See Administration and Security Management Tool Guidance for detailed information.

The following steps are intended for the system administrator.

Note: Only one computer connected to port 1 is required for this operation

Restore Factory Defaults will reset all settings on the KVM to their original state

To Restore Factory Defaults via User Menu Options:

KVM mode

CAC port registration will be removed

KVM settings will be reset to factory defaults

1. Open the Administration and Security Management Program

2. Using the keyboard, press the Alt key twice and type “cnfg”

3. Enter the default admin name “admin” and press Enter.

4. Enter the default password “12345” and press Enter.

5. Select option 7 from the menu on your screen and press enter. (Menu shown in Figure 9-1)

Figure 9-1

Advanced Single Port DVI-I Secure KVM 10

LED’s BEHAVIOR

User Console Interface – Display LED:

User Console Interface – CAC LED:

Front Panel – Port LED:

Front Panel – CAC LED:

Front Panel - Port and CAC LED:

IMPORTANT!

# Status Description

1 Off Monitor is not connected

2 On Monitor is connected

3 Flashing EDID problem – Learn EDID to x the problem

# Status Description

1 Off CAC is not connected

2 On Authorized and functional CAC is connected

3 Flashing Non-CAC peripheral is connected

# Status Description

1 Off Non-selected port

2 On Selected port

3 Flashing EDID learn in process

# Status Description

1 Off CAC port is disabled or non-selected port

2 On CAC port is enabled

3 Flashing EDID learn in process

# Status Description

1 All Flashing Connected peripheral to keyboard or mouse

console ports is rejected

If all the Front Panel LED’s

are ashing and the buzzer is

beeping, the KVM has been

TAMPERED with and all

functions are permanently

disabled. Please contact

iPGARD technical support at

suppor[email protected].

If all Front Panel LED’s are on

and not ashing, the POWER

UP SELF TEST has failed and

all functions are disabled.

Check if any of the front

panel port selection buttons

are jammed. In this case,

release the jammed button

and recycle the power. If

power up self test is still

failing, please contact iPGARD

technical support at

suppor[email protected].

EDID Learn - Front Panel LED’s:

All LED’s are turned on for 1 second. Then:

• Port 1 LED’s will ash until the end of the process.

Andere Handbücher für SDVN-1S-P

Inhaltsverzeichnis

Andere IPGARD Schalten Handbücher

IPGARD

IPGARD SA-HDN-4D Bedienungsanleitung

IPGARD

IPGARD SDPN-2S Bedienungsanleitung

IPGARD

IPGARD SDMN-4S-P Bedienungsanleitung

IPGARD

IPGARD SA-HDN-4S Bedienungsanleitung

IPGARD

IPGARD USM-0S0-1M4 Bedienungsanleitung

IPGARD

IPGARD SA-DMN-DP-P Bedienungsanleitung

IPGARD

IPGARD SA-DVN-8S Bedienungsanleitung

IPGARD

IPGARD SA-DVN-2D-P Bedienungsanleitung

IPGARD

IPGARD DPMST-4S Bedienungsanleitung

IPGARD

IPGARD SA-HDN-4S Bedienungsanleitung

IPGARD

IPGARD SDVN-2S Bedienungsanleitung

IPGARD

IPGARD SDPN-2S-P Bedienungsanleitung

IPGARD

IPGARD DPMST-2S-P Bedienungsanleitung

IPGARD

IPGARD SA-KMN-4S-P Bedienungsanleitung

IPGARD

IPGARD SKMN-8S Bedienungsanleitung

IPGARD

IPGARD SDPN-2D Bedienungsanleitung

IPGARD

IPGARD SDVN-8D Bedienungsanleitung

IPGARD

IPGARD SA-DMN-DP-P Bedienungsanleitung

IPGARD

IPGARD SDHN-4D-P Bedienungsanleitung

IPGARD

IPGARD SDVN-8S Bedienungsanleitung

IPGARD

IPGARD Smart-AVI SM-MST-2D Bedienungsanleitung

IPGARD

IPGARD SMART-AVI SM-MST-2S Bedienungsanleitung

IPGARD

IPGARD DPMST-4S-P Bedienungsanleitung

IPGARD

IPGARD SA-DVN-2S Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung