IQRF RC4-01 Bedienungsanleitung

RC4-01

IQRF remote controller

User’s guide

RC4-01

Description

RC4-01 is a universal user-programmable remote controller for IQRF

platform. It is a generic device. Thus, the hardware is fixed and the user-

specific functionality is achieved by the software developed by a user’s

application engineer. The code can be uploaded wirelessly.

Key features

IQRF transceiver TR-76DA inside

Bidirectional RF communication providing high security in comparison

to unidirectional systems

4 pushbuttons

2 LEDs (visible through one peephole)

Ultra low power consumption

Coin battery CR2450

IP66 protection

Programmable via RF (wireless upload). For development and service,

also wired upload is possible.

Applications

Remote controller for arbitrary use

Internet of Things

Block schematics

RC4-01

Electrical specifications Typical values (until otherwise specified)

RF transceiver TR-76DA

Antenna PCB meander built in the transceiver board

RF band 868 MHz or 916 MHz, multiple channels, SW selectable

Effective radiated power Programmable in 8 levels up to the following values:

868 MHz band 6.5 dBm

916 MHz band 2.0 to 6.5 dBm (Depends on the RF channel. See TR-76D datasheet,

diagram ERP vs. channel)

RF range Up to 460 m1, up to 280 m2

Other RF parameters See TR-76D datasheet

Battery CR2450, 3V, 550 mAh, lithium coin cell 24.5 mm x 5 mm

Supply current

TR in Deep sleep mode 100 nA (all TR peripherals inactive, LEDs off, pushbuttons not pressed)

TR in Sleep mode 700 nA (all TR peripherals inactive, LEDs off, pushbuttons not pressed)

Additional supply current

TR not in sleep mode See TR-76D datasheet

LED on 4 mA per LED (rough value for brief guidance only)

Pushbutton pressed 65 µA per pushbutton (rough value for brief guidance only)

Temperature

Operating -10 °C to +50 °C

Storage -10 °C to +30 °C. Higher temperature impacts the battery lifetime.

Size 43 mm x 15.5 mm x 72 mm

Weight 34 g

Note 1: Arrangement: RC4-01 vertically, 1.6 m above the ground. Counterpart: TR-72DA transceiver plugged in

DK-EVAL-04A kit, vertically, 1.6 m abovethe ground. Bidirectional communication, in free space.

Test software: E09-LINK example (STD mode, setRFpower(7), checkRF(0)).

Note 2: Arrangement: RC4-01 held in the hand, horizontally, with the longitudinal axis oriented towards the

counterpart TR, 1.1 m above the ground. Counterpart: TR-72DA transceiver plugged in DK-EVAL-04A kit,

vertically, 1.6 m above the ground. Bidirectional communication, in free space.

Test software: E09-LINK example (STD mode, setRFpower(7), checkRF(0)).

Absolute maximum ratings

Stresses above those values may cause permanent damage to the device. Exposure to maximum rating conditions for

extended periods may affect the device reliability.

Supply voltage 3.5 V

Storage temperature -10 °C to +50 °C. Higher temperature impacts the battery lifetime.

RC4-01

Hardware

Simplified schematics

Power supply

RC4-01 is supplied from the 3 V, 550 mAh lithium non-rechargeable coin 24.5 mm x 5 mm battery CR-2450. It is possible to

use even a battery with higher capacity, e.g. 620 mAh. Exchanging is possible after unscrewing the rear cover. The polarity

must correspond to the silkscreen marking at the bottom PCB side. RC4-01 is protected against damage due to the wrong

polarity.

The power supply can not be switched off at all (unless removing the battery), the TR sleep mode should be used instead of

this. See chapter Sleep mode below.

TR transceiver

The TR-76DA transceiver with built-in PCB antenna is used.

Because the TR is soldered (non-removable), the recommended way

to upload the application code into TR is wireless upload (RFPGM).

Thus, the application engineer should keep a method how to enter

RFPGM during development. See chapter Demo application for details.

However, it is also possible to use wired upload. In this case, the TR

upload interface (with soldering pads only) is intended to connect the

CK-USB-04A programmer by wires. Refer to the CK-USB-04A User’s

guide, chapter In-circuit upload.

Bottom view

RC4-01

Pushbuttons

The functionality of all four pushbuttons S1 to S4 is fully under control of the application software.

All pushbuttons are active at log. high level. To provide log. low level in the inactive state, the pushbutton pins have on-board

pull-down resistors.

The pushbuttons have no hardware protection against contact bouncing when pressed and released. The protection should

be ensured in software.

Arrangement:

LEDs

Green LED and red LED are connected to TR pins dedicated to IQRF OS and DPA indication. Additionally, during normal

operation, the functionality of both LEDs is under control of application software. They are active at log. high level.

Both LEDs are visible through one peephole.

Hardware revision

v1.01 First release.

RC4-01

Operation

Battery low indication

OS function getSupplyVoltage() should be used to check the battery. The Demo example uses approx. 2.6 V as the

threshold voltage.

Sleep mode

To minimize the supply current, it is possible to switch off all functions and peripherals and put the TR into Sleep mode.

Wake-up is possible when any pushbutton is pressed. For the Sleep mode configuration and control, refer to the Demo

example included.

In special cases (e.g. for long-lasting storage), the Deep sleep mode with even less power consumption can be utilized.

Pushbuttons

The protection against contact bouncing should be performed in software. See the Demo example.

Besides of the essential purpose (sending RF packets for remote control), the pushbuttons can also be used for other tasks,

e.g. to switch the RC4-01 to/from the RFPGM mode (wireless TR upload). The Demo example illustrates launching RFPGM

when the pushbuttons S3 and S4 are pressed long at the same time and premature terminating RFPGM by the short press

of any pushbutton.

LEDs

IQRF OS uses both LEDs for RFPGM mode indication. Refer to the IQRF OS User’s guide, chapter RFPGM for description.

The application SW can managed LEDs directly (e.g. LEDG = 1;) or utilizing the appropriate OS functions (e.g.

pulseLEDR()).

RC4-01

Demo application example

The RC4-01 functionality can be designed fully according to the user’s desire. The Demo application example RC4-01_demo

provided with this product can be used for non-networking applications, either as it is or it can freely be adapted as required.

The Demo illustrates transmitting of unidirectional non-networking packets. They can be received e.g. by a TR-72DA

transceiver with the E03-TR example uploaded. Every received packet is indicated by the red LED flash. Received data can

be visualized e.g. when the receiving TR is plugged in the CK-USB-04A development kit connected to PC with the IQRF IDE

Terminal running.

The Demo application can be downloaded from RC4-01 product page and E03-TR is one of IQRF Basic examples, available

in the IQRF Startup package. To upload the Demo .HEX file via RF, see the IQRF OS User's guide, Appendix RFPGM.

Switching to RFPGM mode after reset is enabled by default.

In the idle state, the controller stays in Sleep mode, allowing wake-up by any pushbutton. After wake-up, the battery voltage

is checked and LEDs flashing indicates pressing the button and the accumulator condition. Then the respective command is

performed and the controller gets to sleep again. Besides the information about the pushbutton, every transmitted packet

also reports the battery status.

Buttons Function

S1 Text sent: "S1x" x=0 if battery O.K., otherwise x=1

S2 Text sent: "S2x" -"-

S3 Text sent: "S3x" -"-

S4 Text sent: "S4x" -"-

S3 and S4 for more than 5 s Enter RFPGM mode

Any button for more than 0.7 s Leave RFPGM mode

LED indication

Button S1 to S4 pressed 1 x flash green (battery O.K.) / red (battery exhausted).

RFPGM indication See the IQRF OS User's guide, Appendix RFPGM, indication in RFPGM LP mode.

This Demo can also plug-and-play remotely control the relays on IQRF development kit DDC-RE-01 in the following

configuration:

See the comments in the DDC-RE-01 Demo example source code provided with this kit.

RC4-01

Caution: The Demo software version should correspond to IQRF OS version implemented in RC4-01.

To read out the OS version, catch Module Info which is always sent by this Demo application just before switching to RFPGM

mode in IQRF IDE Terminal. The Data HEX checkbox should be activated for this. OS version is stored in buffer

moduleINFO[4]. See the picture below and IQRF OS Reference guide.

Example:

moduleINFO[0–7]:

[0] [1] [2] [3] [4] [5] [6] [7]

D5 CF 10 81 42 B4 B8 08

moduleINFO[4] = 42 means OS v4.02D

Caution:

The standard way how to upload the user application into the RC4-01 is RFPGM (in-circuit wireless programming). The

Demo application RC4-01_demo.c invokes the enableRFPGM() function first. It ensures that after every reset (due to

reconnecting the battery) the device is switched to RFPGM mode and can possibly be reprogrammed. This feature can

be removed (by disableRFPGM()), but it should not be done unless there is another reliable way how to invoke back the

RFPGM mode using runRFPGM() after pressing a pushbutton. See the Demo application and refer to the IQRF OS User's

guide, Appendix RFPGM for details. If being omitted, the device can not be reprogrammed wirelessly anymore until it is

recovered by wired upload using the PCB pads inside the case only.

Tip: If wired upload via the PCB pads is not comfortable for you, always use enableRFPGM() during the development.

RC4-01

Product information

Ordering code

RC4-01 Generic IQRF remote controller

Supplied contents

RC4-01 Generic IQRF remote controller. TR-76DA inside, with RC4-01_demo uploaded, TR in sleep when

delivered from the factory.

BK-CR2450-1B Lithium coin cell battery CR2450 (550 mAh) inside

Charm chain Not included

Hardware revision

v1.01 First release

Document history

180629 First release

RC4-01

Sales and Service

Corporate office

MICRORISC s.r.o., Prumyslova 1275, 506 01 Jicin, Czech Republic, EU

Tel: +420 493 538 125, Fax: +420 493 538 126, www.microrisc.com

E-mail (commercial matters): sales@microrisc.com

Technology and development

www.iqrf.org

E-mail (technical matters): support@iqrf.org

Partners and distribution

www.iqrf.org/partners

Quality management

ISO 9001 : 2009 certified

Complies with ETSI directives EN 301 489-1 V1.9.2:2011, EN 301 489-3 V1.6.1:2013,

EN 300 220-1 V3.1.1:2017, EN 300 220-2 V3.2.0:2017 and ERC Recommendation

70-03 (2017) and VO-R/10/05.2014-3.

Complies with directives 2011/65/EU (RoHS) and 2012/19/EU (WEEE).

Trademarks

The IQRF name and logo are registered trademarks of IQRF Tech s.r.o.

PIC, SPI, Microchip and all other trademarks mentioned herein are the property of their respective owners.

Legal

All information contained in this publication is intended through suggestion only and may be superseded by updates without

prior notice. No representation or warranty is given and no liability is assumed by IQRF Tech s.r.o. with respect to the

accuracy or use of such information.

Without written permission, it is not allowed to copy or reproduce this information, even partially.

No licenses are conveyed, implicitly or otherwise, under any intellectual property rights.

The IQRF® products utilize several patents (CZ, EU, US).

On-line support: support@iqrf.org

Inhaltsverzeichnis

Andere IQRF Fernbedienung Handbücher

IQRF

IQRF RC-04 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung