IRIS Energy Smart ES2H40HD045V Betriebsanleitung

Energy Smart®Electric

Water Heater Controller

100261231

Installation, Operation and

Troubleshooting Instructions

Table of Contents

Installation and Setup, 2

Operation, 5

Troubleshooting, 7

Regulatory Notices, 11

INSTALLATION AND SETUP

1Get to know your Energy Smart®

Electric water heater controller.

With your new electric water heater controller, you can:

• Monitor and control your water heater with a smart

phone, tablet, or computer over your home’s wireless

(WiFi) network.

• Receive alerts when you’re low on hot water.

• Create custom water heating schedules that are

controlled by your computer or other device through

your home’s WiFi network.

Reset Button Beeper

Status LED

Figure 1.

MAC

Address

Label

2Review the requirements.

To get started, you will need:

• A working wireless (WiFi) network router with Internet

access.

• A personal computer, smart phone, or tablet computer

connected to your home’s WiFi network.

• One of the following water heater models:

ES2H40HD045V, ES2J40HD045V, ES2H50HD045V,

ES2J50HD045V, ES2J65HD045V, ES2H80HD045V,

ES2J80HD045V, ES40R92-45D, ES40R123-45D,

ES50R92-45D, ES50R123-45D, ES80H123-45D.

• One #2 Phillips screwdriver.

Read and follow all of the instructions, cautions, and

warnings in your water heater’s use and care guide.

WARNING! Even if the water heater’s temperature

control is set to a relatively low temperature, hot

water can scald. Install thermostatic mixing valves at

each point-of-use to reduce the risk of scalding.

3Install the Controller.

WARNING! Working on an energized circuit can result

in severe injury or death from electrical shock. Turn power

off before performing this installation. Check wires with a

non-contact circuit tester to make sure power is off.

tep 2:

Remove access cover.

Discard screws.

Longer screws

provided.

Do NOT remove

junction box covers. Connection Pins

Figure 2.

tep 1: Turn power off at source (circuit breaker).

are installed as described in step 4 above. Screws

must be installed to prevent equipment damage.

Step 4:

Secure controller

with the longer

screws (2). The

longer screws are

provided with the

controller.

Cover

Access

Port

Controller

Step 3: Plug controller

into water heater.

WARNING! Do not turn power on unless screws

Step 5: Turn water heater’s power back on according

to its use and care guide.

Step 6: Watch the water heater’s display screen for

the Grid icon to appear (Figure 3). This may

take a minute or so after power has been

turned on.

Step 7: Activate the screen by touching any button,

then releasing it.

Step 8: If the screen is locked, touch and hold the

Lock button for at least 5 seconds. The Lock

icon will disappear from the screen. This

indicates that the control buttons have been

unlocked. See Figure 3.

Step 9: Touch the Grid Enabled button (top right).

The Grid Enabled button must be lit before

continuing with the set up.

°F/°C

GRID

ENABLED

VACATION

STANDARD

ENERGY

SMART

LOCK

ELEMENT ALERT GRID

Figure 3.

Water Heater User Interface

(located on the front of your Energy Smart®

electric water heater).

Grid Enabled Button

Lock Button

Grid Icon

NOTE: The appearance of the

screen and icons may vary.

4Complete Setup.

Step 1: Check the Status LED on the controller.

The Status LED should brighten gradually, then

dim suddenly. If it does not brighten gradually

and dim suddenly, press the reset button 8

times with a paper clip (about once per second)

until you hear a beep. See Figure 1. The beep

indicates that the controller has been reset.

Step 2: Open a wireless network control panel on your

device (computer, smart phone or tablet).

A list of available wireless networks should be

displayed (Figure 4).

Step 3: Disconnect your device (computer, smart

phone or tablet) from your home’s WiFi

network.

You will connect to a different network during the

next step.

Example: List of SSIDs Displayed in

Available Wireless Networks

Figure 4.

Step 4: Select the “energySmart” network (Figure 5).

Your device (computer, smart phone or tablet)

will connect to it.

Select “energySmart” Network

Figure 5.

Step 5: Once your computer is connected to the

energySmart network,

A. Open a browser window.

B. Type 192.168.10.1 into the browser’s Ad-

dress or Location bar, then press [Enter].

See Figure 6.

NOTE: The page may load automatically when

the browser window is opened.

Browser’s Address/Location Bar

Figure 6.

Step 6: Follow these steps to connect the controller

to your network:

A. Locate your home’s wireless network in the

list (Figure 7).

B. IMPORTANT: If your router is set to hide

its SSID, look for its MAC address instead.

You will be asked to enter its SSID during

the next step.

C. Click the “Join” button next to your home’s

wireless network (Figure 7).

D. If necessary, type your wireless network

password in the dialog box, then click OK.

E. When you have connected successfully, the

Status LED will be on steady (no blinking,

ﬂashing, or dimming). However, if you don’t

get a steady LED status light, repeat all

steps in this section.

Step 7: Reconnect your device (computer, smart

phone or tablet) to your home’s wireless

network.

Step 8: Register and sign in as described in the next

step.

5Get started with Iris®.

Before you try to sign in, check the following:

• The Energy Smart®Electric Water Heater Controller

must be connected to your home’s wireless network.

• Your home’s wireless network must be connected to

the Internet.

• The controller must be enabled before you can

control and monitor your water heater through Iris®.

See “

Install the Controller,” Steps 6 through 9.

For more information about your water heater’s user

interface, see your water heater’s use and care guide.

To get started with Iris®, follow these steps:

Step 1: Register, then sign in to your Iris®account at:

www.lowes.com/iris

Step 2: Click the ‘Add Devices’ button.

Step 3: Follow the on-screen instructions.

Customer Care

If you need assistance, call 855-469-IRIS. Help is also

available at www.lowes.com/iris/support.

{MAC Address}

Your Wireless Network

Figure 7.

OTHER

OPERATION

User Controls and Indicators

Reset Button Beeper

Status LED

Figure 8.

MAC

Address

Label

°F/°C

GRID

ENABLED

VACATION

STANDARD

ENERGY

SMART

LOCK

ELEMENT ALERT GRID

Figure 9.

Water Heater User Interface

(located on the front of your Energy Smart®

electric water heater).

Grid Enabled Button

Lock Button

Grid Icon

NOTE: The appearance of the

screen and icons may vary.

Status LED

The green LED on top of the controller indicates its

connection status or error state as described below. See

Figure 8.

See Troubleshooting for an explanation of each ﬂash

code (page 8).

Beeper

Audible beeps indicate status changes that require your

attention. If you hear a beep, refer to the Troubleshooting

section to determine its meaning.

Reset Button

The reset button is located toward the center of the

electric water heater controller (Figure 1).

To reset the controller and put it in Access Point (AP)

Mode:

1. Press the reset button 8 times with a paper clip

(about once per second) until you hear a beep. See

Figure 8.

The beep means that the controller has been

disconnected from the WiFi network and has been

reset.

2. If you can’t connect to an SSID in the available

networks list, repeat step 1. (See Figures 5 & 7).

This may be necessary in areas with multiple WiFi

signals or when the WiFi signal strength is weak.

To restart the controller without going into Access Point

(AP) Mode:

1. Press and hold the reset button down until you hear a

beep (about 12 seconds).

2. Release the button. The controller will reconnect

to the web server. However, it will not default to AP

Mode.

Enabled / Disabled

Enabled

To control your water heater through Iris®, your controller

must be enabled and connected. It is enabled when the

Grid Enabled button is lit up (backlit). See Figure 9.

To enable the controller:

1. Unlock the water heater’s user interface (if it is

locked). To do so, touch the lock button for at least

5 seconds. The Lock icon will disappear from the

screen.

2. Touch the Grid Enabled button until it lights up

(backlit).

Disabled

While disabled, all water heater parameters can be

viewed through Iris®, but they can only be changed

through the water heater’s user interface. This safety

feature can be used to ensure local control only.

The controller is disabled if:

• The Grid Enabled button is not lit up (not backlit)

• The controller’s LED is ﬂashing “3 seconds ON, 3

seconds OFF.”

IMPORTANT: In the event of a power outage, the Grid

Enabled Button will turn OFF automatically. See Figure 9.

Enable it as described in Enabled above.

To disable the controller so that the water heater can only

be controlled locally:

1. Unlock the water heater’s user interface (if it is

locked). To do so, touch the lock button for at least

5 seconds. The Lock icon will disappear from the

screen.

2. Touch the Grid Enabled button until its light goes out

(no longer back lit).

Parameters

You can monitor and control the following water heater

parameters through Iris®: operating mode, temperature

set point (up to Maximum Set Point), and heating

schedule. Estimated Hot Water Level may be viewed

through Iris®.

For safety reasons, your temperature setting through Iris®

cannot exceed the temperature that is programmed into

your water heater’s user interface.

For example, if the user interface on the water heater is

set at 120°F, the set point range in Iris®would be 80°F to

120°F. 120°F would be the Maximum Set Point.

WARNING! Even if the water heater’s temperature

control is set to a relatively low temperature, hot

water can scald. Install thermostatic mixing valves at

each point-of-use to reduce the risk of scalding.

Read and follow all of the instructions, cautions, and

warnings in your water heater’s use and care guide.

Parameter List

When you change any of the following parameters, the

new values will only display on the web user interface.

The remote settings will not be displayed on the water

heater’s user interface, but this will not effect your

intended settings.

Mode

Standard, Energy Smart and Schedule

Set Point

Temperature setting range: 80°F to 150°F (27°C to 65°C).

NOTE: Your temperature setting through Iris®cannot

exceed the temperature that is programmed into the water

heater’s user interface.

Heating Schedule

This parameter allows you to set water heating schedules

through Iris®.

Estimated Hot Water Level

The estimated hot water level may be viewed through Iris®.

This parameter is not conﬁgurable.

TROUBLESHOOTING

Frequently Asked Questions

Q. The power to my house went out. When it came

back on, I couldn’t control my water heater

through Iris®. What’s wrong?

A. In the event of a power outage, the Grid Enabled

Button will turn OFF automatically. When it does,

the controller is disabled and your water heater

cannot be controlled through Iris®. To restore

functionality, follow the instructions in the Enabled

section, page 6.

Q. I’m trying to increase the water temperature

setting though Iris®. It doesn’t work. Why won’t

it work?

A. For safety reasons, your temperature setting

through Iris®cannot exceed the temperature that

is programmed into your water heater’s user

interface. For example, if your water heater itself is

set to 110°F, then 110°F is the highest temperature

setting allowed in Iris®. Check your water heater’s

temperature setting and adjust as necessary.

Q. One of the parameters shown in Iris®is different

than what is displayed on the water heater’s

user interface. Is this okay?

A. Yes. The controlling parameters are displayed in

Iris®. See Parameters on page 6.

Continued on the next page.

Status LED Flash Codes

Status LED: Brief ﬂash On/Off

Description Power Up

Beeper One Brief Beep

Reset Button Effect N/A

Notes / Remedy This ﬂash code occurs when the controller is powering up. See Note 1 at

the end of the troubleshooting section.

Status LED 3 Seconds On, 3 Seconds Off

Description Controller Disabled

Beeper None

Reset Button Effect A reset will change the controller’s state to Access Point (AP) mode. To

reset the controller, press the reset button 8 times with a paper clip (about

once per second) until the controller beeps.

Notes / Remedy This ﬂash code indicates that the controller is disabled. (This may occur

following a power outage.) To enable the controller, unlock the water

heater’s user interface and touch the Grid Enabled button. The Grid

Enabled button LED will turn on. See Figure 9.

NOTE: When unlocking the user interface, you must touch the lock button

for at least 5 seconds. The Lock icon will disappear from the screen.

The following status LED codes will not display when the wireless

controller is disabled:

• Steady On, Brightens Brieﬂy (Connected & Posting).

• Steady On (Connected & Waiting).

• Brightens Gradually, Dims Gradually (Search Mode).

• Brightens Gradually, Dims suddenly (Access Point [AP] Mode).

• 2 Flashes, PAUSE, 3 Flashes, PAUSE, 3 Seconds On, Off

(No Connectivity).

Continued on the next page.

Status LED: Brightens gradually, dims suddenly.

Description Access Point (AP) Mode

Beeper None

Reset Button Effect A reset will cause the controller to re-scan the WiFi networks.

To reset the controller, press the reset button 8 times with a paper clip (about once per

second) until the controller beeps.

Notes / Remedy This state occurs when a new controller is powered up. It will also occur after the wireless

controller has been reset. In this mode, the wireless controller will operate as an access

point to connect to a WiFi local network. See Note 2 at the end of the troubleshooting

section.

Status LED: Steady on, brightens brieﬂy when posting.

Description Connected & Posting

Beeper None

Button Press Effect To change the controller’s state to Access Point (AP) mode, press the reset button 8 times

with a paper clip (about once per second) until the controller beeps.

To restart the controller, press and hold the reset button down until you hear a beep (about

12 seconds), then release. The controller will reconnect to web server.

Notes / Remedy Normal Operation

Continued on the next page.

Status LED Flash Codes (Continued)

Status LED: Steady On

Description Connected & Waiting (No Internet Connectivity)

Beeper None

Button Press Effect To change the controller’s state to Access Point (AP) mode, press the reset button 8 times

with a paper clip (about once per second) until the controller beeps.

To restart the controller, press and hold the reset button down until you hear a beep (about

12 seconds), then release. The controller will reconnect to web server.

Notes / Remedy This state occurs when the internet connection drops while the controller is Connected &

Posting. The controller is still connected to the local WiFi network. Check your router’s

internet access.

Status LED: 2 Flashes, PAUSE, 3 Flashes, PAUSE, 3 Seconds On, Off. (Repeats.)

Description No Connectivity

Beeper None

Button Press Effect None

Notes / Remedy Call 855-469-IRIS. Help is also available at www.lowes.com/iris/support.

Status LED: Brightens Gradually, Dims Gradually.

Description Search Mode

Beeper None

Button Press Effect To change the controller’s state to Access Point (AP) mode, press the reset button 8 times

with a paper clip (about once per second) until the controller beeps.

Notes / Remedy This state occurs when the WiFi connection drops while the controller is Connected &

Posting. (Example: Router power turned off, etc.)

• Verify that the router is powered.

• Verify that the controller is enabled. See

“Install the Controller” on page 2

(steps

through 9).

Continued on the next page.

Status LED Flash Codes (Continued)

Dieses Handbuch passt für folgende Modelle

Andere IRIS Controller Handbücher

IRIS

IRIS Dragonfly VR IDL-20004 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung