Iron-A-Way UD-42 Kurzanleitung

Installation

Manual

MODEL: UD-42

Tools Needed: Supplied Parts:

Recessed Mounting:

- Two #10 x 1 1/2” wood screws for top

portion of cabinet

- Two #14 x 2 1/2” Phillips screws for top

side brackets

Surface Mounting:

- Two #14 x 4” wood screws

GET TO KNOW YOUR UNIT

1. CROSS BRACES

2. ELECTRICAL RACEWAY

3. SIDE BRACKETS

4. ELECTRICAL OUTLET

5. HOT IRON REST

(BOTTOM OF RACEWAY)

- Stud Finder

- 12-14” Level

- Tape Measure

- Small Flathead

Screwdriver

- Electric Drill

(with 1/4” & 1/8” drill bit)

- 1/4” Nut Driver

(optional)

- Safety Glasses

- Utility Knife

PRE-INSTALLATION

2. LOCATE STUDS & UTILITIES

Using a stud nder, locate the wall

studs to be used for mounting.

Locate the existing wiring or other

utilities in the wall to prevent drilling

into/severing a wire and/or other utility

during installation.

1. DETERMINE MOUNTING HEIGHT

Using the charts provided, determine

the mounting height above oor (the

distance between the oor and the

bottom of the cabinet). First choose

your desired ironing board height

from the left column, then locate the

corresponding mounting height in the

right column.

Mounting

Height

Above Floor

Desired Ironing

Board Height

Desired Ironing

Board Height

Mounting

Height Above

Floor

16”

15”

14”

13”

32”

31”

30”

29”

Refer to provided chart to ensure adequate

clearance for ironing. The cabinet door opens

at 180 degrees; allow 16” from side of cabinet

for door to fully open.

3. ENSURE ADEQUATE SPACE

2. Distance from wall to tip of ironing board

4. Standing area clearance (not shown)

The suggested distance from the side of the ironing where the user

typically stands to ensure adequate space for ironing.

1. Distance needed on either side of unit to fully swivel the board

3. Distance from wall to board when in full swivel position

501/4”

167/8”

321/4”

24”

RECESSED INSTALLATION

Cut an opening into the wall based

on dimensions given below.

Attach a 2” x 4” cross support

cleat between the studs so it

is level with the bottom of the

opening. This will give support to

the drywall during installation and

to the cabinet once installed in

the wall.

Your unit will be attached to the studs by

screws in the upper and lower sides of

the cabinet.

Remove electrical raceway by

unscrewing the top and bottom screws.

Using a 1/8” drill bit, pre-drill holes into

the sides of the cabinet, 14” from the top

and 21/2” from the back.

1. CUT WALL OPENING

2. ATTACH CLEATS

3. PRE-DRILL HOLES

Example shown with exposed

studs & unit to illustrate mounting.

14” from top of cabinet

21/2” from back

of cabinet

Note: Instructions assume wall studs are spaced 16” on center.

CLEAT

14 3/8” x 59 7/8” x 3 7/8”

7. ATTACH CABINET TO STUDS

Using the pre-drilled holes in top

of cabinet, attach unit to studs

with two #10 x 11/2” screws for top

installation.

Example shown with studs

to illustrate mounting.

6. INSTALL UNIT IN WALL

Begin installation by carefully lifting unit

into the wall opening. Make sure the

cabinet is plumb and level. If needed,

add shims to help unit t snug in place.

Ensure that power is

disconnected at service

entrance before proceeding.

4. REMOVE ELECTRICAL KNOCKOUT

Open the front cover of the raceway

by removing the screw at the top and

bottom of the raceway.

Locate the electrical knockout, as

specied on diagram provided.

Install a 3/8” romex connector where

the knockout was removed.

21/2”

21/4”

11/4”

DIA. VENT

HOLE FOR

WIREWAY

DOOR

CABINET

EXTERIOR

5. INSTALL ELECTRICAL WIRING

Verify that there is ample supply wire

available to run from the top of the

ironing center to the approximate

location of electrical pigtails.

Note: A free wire length of 48” is

recommended.

Begin to place the ironing center into

its location while feeding the supply

wire through electrical knockout, and

the 3/8” romex connector through the

back of the raceway.

Locate side ironing board brackets

that are secured to cabinet with

three screws. Then remove the

top screw from each bracket. This

is where the bottom part of your

cabinet will be secured to the

studs.

Pre-drill holes into the cabinet using

the holes in side brackets where

screws were just removed.

Finish installation by inserting the

two #14 x 21/2” screws into the

pre-drilled holes to secure bottom

part of cabinet.

8. REMOVE BRACKET SCREW

9. PRE-DRILL HOLES IN SIDES

10. CONNECT WIRES

Connect all power supply wires and

ground wires in accordance with all

electrical codes. Trim supply wire as

necessary.

11. REPLACE RACEWAY COVER

Place the raceway cover into

position, ensuring that no wires

are pinched. Reinstall the top and

bottom screw to secure in place.

Reconnect power supply.

12. INSTALLATION COMPLETE!

Cabinet is now fully installed! If desired,

decorative trim or molding may be

added to cover an irregularities in the

wall.

SURFACE MOUNT INSTALLATION

2. PRE-DRILL PILOT HOLES

Using a 1/4” drill bit, pre-drill holes in

the upper and lower cross braces

inside the cabinet as determined in

previous step. Ensure that the holes in

both braces are drilled to the same

measurement.

1. PREPARE CABINET

Screws will be drilled through the upper

and lower cross braces (see illustration

on pg.3) inside the cabinet. Determine

location of screws, ensuring that the

location of the mounting screw is as

close to the center of the cabinet as

possible.

Example shown

with studs & unit to

illustrate mounting.

Partially insert a #14 x 4” screw

in the upper cross brace.

4. PARTIALLY INSERT SCREW

3. LOCATE & MARK STUD

Using a stud nder, locate stud in

wall and mark the wall according

to the pre-drilled holes in cabinet.

Setting cabinet aside, pre-drill holes

using a 1/4” drill bit. Do not attempt

to drill into hard board of cabinet.

5. REMOVE ELECTRICAL KNOCKOUT

Open the front cover of the raceway

by removing the screw at the top

and bottom of the raceway.

Locate the electrical knockout, as

specied on diagram provided.

Install a 3/8” romex connector where

the knockout was removed.

Ensure that power is

disconnected at service

entrance before proceeding.

241/2”

213/16”

13. INSTALLATION COMPLETE

Cabinet is now fully installed!

9. ADD TRIM

Add decorative trim or molding to

make cabinet sides ush with the face

frame.

Locate side ironing board brackets

that are secured to cabinet with

three screws. Then remove the top

screw from each bracket. Replace

with a #14 x 3/4” Phillips screw. This

will add stability long-term.

10. REMOVE BRACKET SCREW

7. INSTALL UNIT

Begin installation by carefully lifting

unit into position. Then, attach the

cabinet to the wall by fully inserting

the screw in the upper cross brace

into the wall stud.

Make sure the unit is plumb and

level. Shim if necessary. Fully tighten

installation screw.

8. INSERT SECOND SCREW

Insert the second #14 x 4” screw into

the pre-drilled hole in the bottom

brace of the cabinet and attach to

wall making sure cabinet remains

square and level.

6. INSTALL ELECTRICAL WIRING

Verify that there is ample supply wire

available to run from the top of the

ironing center to the approximate

location of electrical pigtails.

Note: A free wire length of 48” is

recommended.

Begin to place the ironing center into

its location while feeding the supply

wire through electrical knockout,

and the 3/8” romex connector

through the back of the raceway.

11. CONNECT WIRES

Connect all power supply wires and

ground wires in accordance with all

electrical codes. Trim supply wire as

necessary.

12. REPLACE RACEWAY COVER

Place the raceway cover into

position, ensuring that no wires

are pinched. Reinstall the top and

bottom screw to secure in place.

Reconnect power supply.

Andere Handbücher für UD-42

Inhaltsverzeichnis

Andere Iron-A-Way Bügelzentrum Handbücher

Iron-A-Way

Iron-A-Way NE-242 Bedienungsanleitung

Iron-A-Way

Iron-A-Way A-46 Bedienungsanleitung

Iron-A-Way

Iron-A-Way E-342 Bedienungsanleitung

Iron-A-Way

Iron-A-Way A-42 Bedienungsanleitung

Iron-A-Way

Iron-A-Way A-46 Bedienungsanleitung

Iron-A-Way

Iron-A-Way UD-42 Bedienungsanleitung

Iron-A-Way

Iron-A-Way UD-42 Bedienungsanleitung

Beliebte Bügelzentrum Handbücher anderer Marken

TEFAL

TEFAL IXEO + Bedienungsanleitung

LauraStar

LauraStar Magic S4 Bedienungsanleitung

UFESA

UFESA PL1445 Bedienungsanleitung

Cissell

Cissell VSBMAN61 Bedienungsanleitung

DOMENA

DOMENA Xecutive 1 Bedienungsanleitung

Kärcher

Kärcher AB 1000 Bedienungsanleitung

Cissell

Cissell SFBMAN99 Bedienungsanleitung

POLTI

POLTI VAPORELLA NEXT VN18.10 Bedienungsanleitung

Kleenmaid

Kleenmaid LWK300 Bedienungsanleitung

Bosch

Bosch TN20 Bedienungsanleitung

Miele

Miele PRI318 G Bedienungsanleitung

LauraStar

LauraStar S PURE Bedienerhandbuch

Advanced Solutions

Advanced Solutions MOBILMAX Bedienungsanleitung

battistella

battistella VAPORSPRINT Gebrauchsanweisung

battistella

battistella SATURNO MAX L.24 Gebrauchsanweisung

battistella

battistella ANDROMEDA MAX VAP 2009 Gebrauchsanweisung

Bieffe

Bieffe JOLLY BF091 Bedienungsanleitung

Siemens

Siemens TN20350 Bedienungsanleitung