Isotech IPS1820D Bedienungsanleitung

DC POWER SUPPLY

(Switching mode)

ISO-TECH IPS1820D RS Stock No. 357-0760

ISO-TECH IPS3610D RS Stock No. 357-0776

ISO-TECH IPS606D RS Stock No. 357-0782

82IP-3610DMB

SAFETY TERMS AND SYMBOLS

These terms may appear in this manual or on the product:

WARNING. Warning statements identify condition or practices that could result in

injury or loss of life.

CAUTION. Caution statements identify conditions or practice that could result in

damage to this product or other property.

The following symbols may appear in this manual or on the product:

DANGER

High Voltage

DANGER

Hot Surface

ATTENTION

refer to Manual

Protective

Conductor

Terminal

Equipotentialit

Eii

FOR UNITED KINGDOM ONLY

NOTE

This lead/appliance must only

be wired by competent persons

WARNING

THIS APPLIANCE MUST BE

EARTHED

IMPORTANT

The wires in this lead are

coloured in accordance with

the following code:

Green/

Yellow: Earth

Blue : Neutral

Brown: Live (Phase)

As the colours of the wires in main leads may not correspond with the colours marking

identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth terminal marked

with the letter E or by the earth symbol or coloured Green or Green & Yellow.

The wire which is coloured Blue must be connected to the terminal which is marked with the

Letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal marked with the letter L

or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact the supplier.

This cable/appliance should be protected by a suitably rated and approved HBC mains fuse;

refer to the rating information on the equipment and/or user instructions for details. As a guide,

cable of 0.75mm ²should be protected by a 3A or 5A fuse. Larger conductors would normally

require 13A types, depending on the connection method used.

Any moulded mains connector that requires removal/replacement must be destroyed by removal

of any fuse & fuse carrier and disposed of immediately, as a plug with bared wires is hazardous

if a engaged in live socket. Any re-wiring must be carried out in accordance with the information

detailed on this label.

Eiii

Statement of Compliance

IPS-1820D, IPS-3610D, IPS-606D

are herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Law of Member States relating to Electromagnetic Compatibility

(89/336/EEC,92/31/EEC,93/68/EEC) and Low Voltage Equipment Directive(73/23/EEC).

For the evaluation regarding the Electromagnetic Compatibility and Low Voltage Equipment Directive,

the following standards were applied:

EN 61326-1: Electrical equipment for measurement, control and laboratory use—EMC requirements (1997+A1:1998 )

Conducted Emission EN 55022 Class A Electrostatic Discharge EN 61000-4-2 (1995)

Radiated Emission (1994)+A1(1995)+A2(1997) Radiated Immunity EN 61000-4-3 (1996)

Current Harmonic EN61000-3-2 Class A Electrical Fast Transients EN 61000-4-4 (1995)

(1995)/A12(1996)/A13(1997)/A1(1998)/A2(1998)/prA14(2000) Surge Immunity EN 61000-4-5 (1995)

Conducted RF Immunity EN 61000-4-6 (1996)

Voltage Fluctuation EN61000-3-3 (1995) Voltage Dip/Interruption EN 61000-4-11 (1994)

Low Voltage Equipment Directive 73/23/EEC

Low Voltage Directive EN 61010-1:(1993)+A2:(1995)

Eiv

CONTENTS

SECTION PAGE

1. INTRODUCTION…………………………………………………………………………….……………………… 1

2. SPECIFICATIONS…………………………………………………………………………………………………… 2

2-1 General…………………………………………………………………………………….……………………. 2

2-2 Constant Voltage Operation…………………………………………………………………………………… 3

2-3 Constant Current Operation…………………………………………………………………………………... 3

2-4 Indicator Meter…………………………………………………………………………………………………. 3

2-5 Insulation………………………………………………………………………………………………………... 3

3. PRECAUTIONS BEFORE OPERATION………………………………………………………………………….. 4

3-1 Unpacking the Switching Power Supply……………………………………………………………………… 4

3-2 Checking the line voltage………………………………………………………………………………………. 4

3-3 Environment……………………………………………………………………………………………………. 5

3-4 Equipment installation and operation………………………………………………………………………… 5

4. THEORY OF OPERATION………………………………………………………………………………………… 6

5. PANEL CONTROLS AND INDICATORS………………………………………………………………………… 9

5-1 Front Panel……………………………………………………………………………………………………… 9

5-2 Real Panel………………………………………………………………………………….……………………. 9

6. OPERATION INSTRUCTIONS……………………………………………………………………………………. 12

6-1 Precaution………………………………………………………………………………….……………………. 12

6-2 Setting Current Limit…………………………………………………………………………………………... 12

6-3 Constant Voltage/Constant Current Characteristic…………………………………………………………. 13

6-4 Operation Mode………………………………………………………………………………………………… 14

7. MAINTENANCE…………………………………………………………………………………………………… 15

7-1 Fuse Replacement………………………………………………………………………………………………. 15

7-2 Line voltage Conversion………………………………………………………………………………………... 15

7-3 Adjustment……………………………………………………………………………………………………… 16

7-4 Cleaning…………………………………………………………………………………………………………. 18

1. INTRODUCTION

This series of switched mode power supplies have removed the inconvenience of big volumes and heavyweight

associated with traditional power supplies.

The output voltage and current are controlled by two variable resistors with coarse and fine regulation for simple and

precise adjustment.

Features:

lWide input voltage range— 97V~133V (for 115V) and 195V~265V (for 230V).

lWith high frequency operation the size of power the transformer is reduced

lWith small size, light weight and high power density.

lEntire efficiency rate up to 70%.

lConstant current and constant voltage modes.

lZero adjustment for the voltage and current output.

2.SPECIFICATION

2-1. General

Mains supply : 115V/230V±15% 50/60Hz(Switch selectable).

Rating, dimension and weight : See Table 2-1.

Table 2-1

MAX. RATING INPUT RATING FUSE STYLE & RATING WEIGHT

Model Voltage Current Watts VA 115V 230V kg

IPS-1820D 18V 20A 500 900 T 10A 250V T 6.3A 250V 3.3

IPS-3610D 36V 10A 500 900 T 10A 250V T 6.3A 250V 3.3

IPS-606D 60V 6A 500 900 T 10A 250V T 6.3A 250V 3.3

Dimensions：128(W) ×145(H) ×285(D) mm.

WARNING: Voltage over 60V DC is a lethal shock hazard to the user. Be careful when

connecting power supplies in series to achieve voltage higher than 60V DC totally or 60V

DC between any connection and earth ground.

Operation Environment : Indoor use,

Altitude up to 2000m,

Installation Category II,

Pollution degree 2.

Operation Temperature &Humidity : 0℃to 40℃, <80%.

Storage Temperature & Humidity : -10℃to 70℃, <70%.

Accessories : Test Lead (current < 4A)…………………………………………… × 1

Operation Manual ..………………………………………………………… × 1

2-2.Constant Voltage Operation

(1) Output Voltage ranges from 0 to rated voltage with continuous adjustment.

(2) Voltage regulation

line regulation≦5mV.

load regulation≦5mV.

(3) Recovery time≦500µs(50% Load change, minimum load 0.5A).

(4) Ripple & Noise≦5mVrms, 100mVp-p (tested by 20MHz oscilloscope.)

(5) Temperature coefficient≦100ppm/℃.

2-3.Constant Current Operation

(1) Output current ranges from 0 to rated current with continuous adjustment.

(2) Current regulation

line regulation≦3mA.

load regulation≦3mA.

(3) Ripple & Noise≦3mArms (IPS-606D).

≦5mArms (IPS-3610D).

≦10mArms (IPS-1820D).

2-4.Indicator Meter

1)Voltage:

Display : 3 1/2 Digits 0.39” Green LED display.

Accuracy : ±(0.5% of reading + 2 digits).

2)Current:

Display : 3 1/2 Digits 0.39” Red LED display.

Accuracy : ±(0.5% of reading + 2 digits).

2-5.Over Voltage Protection

(1) Over Voltage Protection ranges from 5% rating to rating +5.5%.

(2) OVP Accuracy ±(Vset 1%+0.6V)

2-6.Insulation

Between Chassis and Output Terminal : ≧20MΩ(DC500V).

Between Chassis and AC Cord : ≧30MΩ(DC500V).

3. PRECAUTIONS BEFORE OPERATION

3.1 Unpacking the Switched ModePower Supply

The instrument has been fully inspected and tested before shipping from the factory. Upon receiving the instrument,

please unpack and inspect it to check if there is any damages caused during transportation. If any sign of damage is

found, notify the bearer and/or the dealer immediately.

3.2 Checking the Line Voltage

The instrument can be connected to any of the line voltages shown in the table below. Before connecting the power

plug to an AC line outlet, make sure the voltage selector on the rear panel is set to the correct position corresponding to

the line voltage. The instrument might be damaged if connected to the wrong AC line voltage.

WARNING: To avoid electrical shock the power cord protective grounding conductor must be

connected to ground.

When line voltages are changed, replace the required fuses shown below.

Line voltage Range Fuse Line voltage Range Fuse

115V 97-133V T 10A 250V 230V 195-265V T 6.3A 250V

WARNING: To avoid personal injury, disconnect the power cord before removing the fuse

holder.

3.3 Environment

The normal ambient temperature range of this instrument is from 0°to 40°C (32°to 104°F). Operation of the

instrument above this temperature range may cause damage to the circuits.

Do not use the instrument in a place where strong magnetic or electric fields exist as they may disturb the

measurement.

3.4 Equipment Installation, and Operation

Ensure there is proper ventilation for the vents in the IPS power supplies case. If this equipment is used in a manner

not according to the specification, the protection provided by the equipment may be impaired.

WARNING: This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Isotech Stromversorgung Handbücher

Isotech

Isotech IPS 3303D Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung