ISP Technologies HDDS SM800 Bedienungsanleitung

PRECAUTIONS!

Please read this very carefully before operating this unit

Read ALL instructions carefully before using this unit.

Do not operate this unit near water, in the rain, or where there is

moisture. If this warning is ignored a serious electrical shock or death

may occur.

Do not attempt to service this unit. No user serviceable parts inside.

Refer servicing to qualified, ISP approved service personnel.

Never remove or defeat the ground connection on the power cord of

the Master Control Module that is connected to the HDDS SM800.

Care should be taken to avoid spilling any foreign objects or liquid

into this unit.

Failure to follow these instructions may void the warranty.

CAUTION:

DO NOT CONNECT THE CAT6 INPUT CABLE BETWEEN THE MASTER CONTROL

MODULE AND THE INPUT OF THE HDDS SM800 SPEAKER WHEN THE POWER

ON THE MASTER CONTOL MODULE IS SWITHED ON! THE MASTER CONTROL

MODULE MUST BE SWITCHED OFF PRIOR TO CONNECTION. THE HDDS SM800

MUST BE POWERED ON WITH SYMETTRICAL POWER IN ORDER TO CHARGE

BOTH POSITIVE AND NEGATIVE INTERNAL POWER SUPPLIES. FAILURE TO

POWER DOWN THE MASTER CONTROL MODULE PRIOR TO CONNECTION TO

THE HDDS SM800 MAY CAUSE POSSIBLE DAMMAGE TO THE HDDS SM800 OR

THE CONTACTS PINS OF THE CAT6 CABLE DUE TO LARGE NON-SYMETRICAL

INRUSH CURRENT.

INTRODUCTION

Thank you for your purchase of the ISP Technologies High Definition Distributed System

HDDS SM800 Surface Mount Speaker. This product provides a new level of

performance in distributed audio systems allowing greater system flexibility and easy

installation of distributed sound. All connections are made via CAT6 RJ45 connections

making installation of systems faster and easier using the HDDS SM800.

PRECAUTIONS

NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PROVIDE

YEARS OF TROUBLE FREE USE. THIS UNIT REQUIRES CAREFUL HANDELING.

All warnings on this equipment and in the operation instructions should be adhered to and

all operating instructions should be followed.

Do not use this equipment near water. Care should be taken so that objects do not fall

onto and liquids are not spilled into the unit through any openings.

The power cord should be unplugged from the Master Control Module when the unit is left

unused for an extended period of time.

DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. THIS EQUIPMENT SHOULD BE

SERVICED BY QUALIFIED SERVICE PERSONNELL ONLY. DO NOT MAKE ANY INTERNAL

ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT AT ANY TIME. DO NOT TAMPER

WITH INTERNAL ELECTRONIC COMPONENTS AT ANY TIME. FAILURE TO FOLLOW THESE

INSTRUCTIONS WILL VOID THE WARRANTY OF THIS EQUIPMENT, AND MAY CAUSE A

SHOCK HAZZARD.

OPERATION

The HDDS Master Control Module is the Master control center for distributed sound

systems using the HDDS technology. The Master Control Module includes six zones

that can be used independently or can be linked to work together allowing the system

designer the flexibility to set up any system with the desired configuration. The block

diagram below shows the basic configuration of the HDDS SM800 Surface Mount

Speaker. The speaker receives power and audio over a CAT6 cable connected to the

Master Control Module, internally converts the AC power to plus / minus 15VDC and

30VDC to power the amplifier. The audio signal is fed to a precision differential

amplifier to remove any common mode noise, filtered with a crossover circuit to

produce a low pass and high pass signal, equalized and fed to DAAT Dynamic Adaptive

Amplifier power amplifier circuits to drive both the woofer and tweeter in the speaker.

The woofer section will dynamically increase the positive and negative power supply

rails as required based on the audio signal. The output swing can exceed 120 volts and

can deliver over 220 watt continuous output power. The HDDS SM800 includes a rear

panel level adjustment that allows simple balancing of installed systems.

The HDDS SM800 requires connection to the Master Control Module with CAT6 cable in

order to handle the current of the HDDS SM800. The output connection can be used to

connect to not more than one additional HDDS SM800. Connecting more than one

additional HDDS SM800 can exceed the maximum output current available per output

of the HDDS Master Control Module and may trip the internal resettable fuses in the

output circuit.

DO NOT CONNECT THE CAT6 INPUT CABLE BETWEEN THE MASTER CONTROL MODULE AND

THE INPUT OF THE HDDS SM800 SPEAKER WHEN THE POWER ON THE MASTER CONTOL

MODULE IS SWITHED ON! THE MASTER CONTROL MODULE MUST BE SWITCHED OFF PRIOR

TO CONNECTION. THE HDDS SM800 MUST BE POWERED ON WITH SYMETTRICAL POWER IN

ORDER TO CHARGE BOTH POSITIVE AND NEGATIVE INTERNAL POWER SUPPLIES. FAILURE TO

POWER DOWN THE MASTER CONTROL MODULE PRIOR TO CONNECTION TO THE HDDS SM800

MAY CAUSE POSSIBLE DAMMAGE TO THE HDDS SM800 OR THE CONTACTS PINS OF THE CAT6

CABLE DUE TO LARGE NON-SYMETRICAL INRUSH CURRENT.

Rear Panel

The rear panel of the HDDS SM800 includes two RJ45 connectors, connect the INPUT

to the output of the HDDS Master Control Module and the output can be used to

connect to not more than one additional SM800 speaker. The maximum CAT6 cable

length should not exceed 300 feed. The level control allows individual speakers to be

balanced in a given system. The HDDS SM800 will typically pull less than 2 amps of

current from the output of the Master Control Module at average listening levels. At

maximum or peak level the HDDS SM800 can pull in excess of 3 amps of current.

Longer runs of CAT6 cable will reduce the maximum output power of the HDDS SM800.

Connect the HDDS SM800 to any of the A, B or C outputs on the rear of the HDDS

Master Control Module as shown below. Do not connect more than two HDDS SM800

speakers per output on the Master Control Module.

SPEAKER POWER:

The HDDS system distributes low voltage Alternating Current over the CAT6 cable plus

high level balanced audio and is capable of greater than 150 watts continuous power

per HDDS SM800 speaker. Each of the three outputs A, B and C are capable of

delivering up to 7 amps of output current.

CAT6 Connections

The figure below shows the connections for each output A, B and C of each zone output

on the Master Control Module and also connections between each HDDS SM800

speaker. Connections are done via standard CAT6 cables where pins 1 through 8 are

connected common to the same pins 1 through 8 at each end. As shown below two

wires in the Cable are used for balanced audio and 6 wires are used for power with two

providing ground and two for each of two 22VAC power signals fed down the cable.

The HDDS SM800 is a wall mountable Speaker The SM800 works excellently for

foreground and background music plus music-plus-paging systems. Low frequency

output can be augmented with the addition of the HDDS SB112subwoofer. The SM800

loudspeaker is packaged with a bracket for easy wall mounting.

Mounting the HDDS SM800

Refer installation to a qualified installer to ensure proper mounting to overhead

structures. The HDDS SM800 includes a wall mounting bracket for easy install. The

HDDS SM800 weighs 14.5 lbs, make sure to use mounting hardware in accordance with

local safety standards for suspending 14.5 lbs.

HDDS SM800 SPECIFICATIONS

Speaker Type: 2-way active

Low Frequency: 8″ cone

High Frequency: 1″ Silk Dome Tweeter

Crossover: 4th order LR high pass and low pass

Maximum SPL: 118 dB peak, 112 dB long-term

Nominal Coverage Angle: 100 deg. H x 80 deg. V

Frequency Range (-10 dB): 45 Hz –20 kHz

Frequency Response (+-3 dB): 60 Hz –19 kHz

Audio Input: Balanced 30k input impedance

Amplifier Power: 115 WRMS continuous LF, 35 WRMS continuous HF

Backplate: INPUT / OUTPUT RJ45 Connectors, Remote level control

Size: 16.5″ H x 10.8″ W x 10″ D

Weight: 14.5 lbs

Enclosure: ABS Plastic

Grille: Powder Coated Steel

Mounting Hardware: Included wall mounting bracket

WARRANTY AND SERVICE

The unit, parts and workmanship are fully guaranteed to be free of defects under

normal use and service for a period of 3 years from the date of purchase.

Any damage resulting from the misuse or the failure to follow the precautions and

instructions will void the warranty.

In the event that the unit needs to be repaired, please return the unit to ISP

Technologies directly. Simply repack the unit, send a copy of the original receipt, a

note stating the problem, and send it to:

ISP Technologies, LLC

5479 Perry Drive Unit B

Waterford, MI 48329

Attn: Repair Dept.

All shipping charges must be fully prepaid.

ISP will not be responsible for any damages incurred in shipping of any unit. Any claim

will need to be settled with the shipping company.

The warranty will be voided if the serial number has been tampered with in any way.

The warranty card must also be filled out and returned in order to activate the

warranty.

Should you have any questions for the repair department prior to returning the product

please call 1-(248)-673-7790

NOTE: This Product is covered under multiple patents pending.

ISP TECHNOLOGIES, LLC

5479 PERRY DRIVE SUITE B

WATERFORD, MI. 48329

248-673-7790

FAX: 248-673-7696

WWW.ISPTECHNOLOGIES.COM

Inhaltsverzeichnis

Andere iSP Technologies Sprecher Handbücher

iSP Technologies

iSP Technologies HDDS SM652-B Bedienungsanleitung

iSP Technologies

iSP Technologies HIGH DEFINITION LINE 2208Active Series Bedienungsanleitung

iSP Technologies

iSP Technologies VECTOR FS Bedienungsanleitung

iSP Technologies

iSP Technologies HDDS SM 650W Bedienungsanleitung

iSP Technologies

iSP Technologies HDDS Series Bedienungsanleitung

iSP Technologies

iSP Technologies HDDS CS651 Bedienungsanleitung

iSP Technologies

iSP Technologies VMAX 1500 Bedienungsanleitung

iSP Technologies

iSP Technologies HDDS CS650 Bedienungsanleitung

iSP Technologies

iSP Technologies ACTIVE 3112 Bedienungsanleitung

iSP Technologies

iSP Technologies VT110 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung

iSP Technologies HDDS SM800 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken