ITI Interrogator 200 Bedienungsanleitung

Page 1

Audio Verification Module

nUse a maximum of 500 feet of cable for all

speakers and microphones.

Tools Needed

nPhillips screwdriver

nMounting screws and anchors (included)

nDrill and bits

n3-conductor, 22-gauge shielded stranded wire

n2-conductor, 18-gauge stranded wire

Installation

To mount the AVM:

1. Route both 2 and 3-conductor wire cables from

the module to the panel.

2. Remove the cover screws from the module cover

and rotate it away from the base. Set the cover

and screws aside.

3. Remove the speaker plate screws and lift the

speaker plate off the back box (see Figure 1).

Figure 1. Removing the Speaker Plate

8557113A.DS4

SPEAKER

PLATE

Interrogator®200 Audio

Verification Module (AVM)

Document Number: 466-1621 Rev. A

October 1998

Installation

Instructions

Product Summary

The Interrogator 200 Audio Verification Module

(AVM) gives the central station operator the ability to

hear what’s happening at the premises during an

alarm and speak directly to the system owner. The

operator can determine how serious an alarm is, find

out what kind of help is needed, and dispatch the

appropriate assistance.

Control Panel Compatibility: SIMON ™

Only Version 2 (# 60-776)

Installation Guidelines

Use the following guidelines when installing the

AVM:

nYou can install one AVM per panel.

nWire speakers (voice terminals) in series and the

DC voltage, ground, and microphone wires in

parallel.

nUse separate cables for the speakers and the

power, ground, and microphone wires to prevent

cross talk between the microphone and the

speaker.

nUse 3-conductor, 22-gauge shielded wire from the

AVM power, ground and microphone to the

panel. Shielded cable reduces electrical noise and

cross talk.

nUse 2-conductor, 18-gauge wire from the speakers

to the panel.

60-787

8569G04A.DS4

Audio Verification Module

Page 2

4. Place the back box on the wall at the desired loca-

tion and mark mounting holes (see Figure 2).

Figure 2. Mounting Hole Locations

5. Install anchors if needed and secure the back box

to the wall with the enclosed screws.

6. Feed the cables through one of the cable holes in

the back box (see Figure 3).

Figure 3. Cable Holes and Channels

7. Align the back box mounting screw key holes

with the two mounting screws and slide down.

8. Level the back box and tighten the mounting

screws.

9. Feed the cable through the large hole on the

speaker plate.

10. Replace the speaker plate on the back box.

Wiring the AVM to the Control

Panel

To wire the AVM to the control panel:

1. Unplug the transformer and the battery.

2. Plug the panel cable, supplied with the AVM, into

the back of the control panel.

3. Connect terminals as shown in Figure 4. Use 18-

gauge wire for speakers and 22-gauge for power,

ground, and microphone.

Figure 4. Wiring the AVM to the Control Panel

4. Connect the black speaker wires on the AVM to

the blue wires on the control panel cable using the

18 gauge wire.

5. Connect power on the AVM to the red wire on the

control panel cable using the 22 gauge wire.

6. Connect the shielded cable drain wire (bare wire

shown in Figure 5) to the black wire on the control

panel cable and ground on the AVM.

Figure 5. Shielded Cable Detail

8557114A.DS4

MOUNTING SCREW

KEY HOLES

8557115A.DS4

CABLE

HOLES

8569G01C.DS

SPLICE

BLACK

YELLOW

CABLE

SHIELD

YELLOW

SPLICE

RED

BLUE

CONTROL PANEL CABLE CONNECTOR

(INCLUDED WITH AVM)

3-CONDUCTOR

22-GAUGE

SHIELDED

STRANDED WIRE

2-CONDUCTOR

18-GAUGE

STRANDED

WIRE

SPLICE

–

BLACK

INSULATED WIRE

SHIELDED

CABLE

DRAIN

WIRE

8569G02A.DS4

Audio Verification Module

Page 3

7. Splice the yellow wire on the AVM to one end of

the microphone cable and the other end to the yel-

low wire on the control panel cable.

8. Replace the AVM cover and screws.

Powering Up

To power up the panel and AVM:

1. Make sure all wires are connected correctly and

securely crimped.

2. Apply AC and battery power to the panel.

Programming

Programming the AVM involves entering the

following:

nEnabling AVM

nAVM mode of operation

nFire shutdown

nPanic talk

Enabling the AVM - Option 33

To allow the user or Central Station use of the AVM,

option 33 must be on. To turn option 33 on, follow

these steps:

1. Press Add from the Start Menu on the Control

Panel.

2. Press Option #, 33.

3. Press DONE.

Setting the AVM Mode - Option 47

The following describes the available AVM operating

modes.

Call-back - Option 47 is on

After reporting an alarm, the panel answers on the first

ring. A 5 minute window allows remote access alarm

verification after an alarm is reported.

This window is activated after an alarm has been

reported and allows access to the AVM after one ring

at the alarm site. The 5 minute window is cleared

when the monitoring service operator hangs up using

99.

Instant - Option 47 is off

The central station traps the panel when it reports an

alarm. Monitoring personnel can then initiate anaudio

session from a central station parallel telephone.

Fire Shutdown - Option 46

Shutdown - Option 46 is on

Fire sirens will be shut down at the customer site when

audio access is gained. Instead of sirens, the system

will beep every ten seconds.

Doesn’t Shutdown - Option 46 is off

Fire sirens will continue to sound at the customer site

when audio access is gained.

The default is off.

To turn Option 46 on:

1. Press Add from the control panel’s Start Menu.

2. Press Option #, 46.

3. Press DONE.

Panic Talk- Option 48

Talk - Option 48 is on

The central station operator is able to speak to the

person at the customer site during a silent alarm.

Listen Only - Option 48 is off

The central station operator is only able to listen to the

customer site during a silent alarm. The central station

will not be able to put the system into speak mode.

The defaul is off.

To turn Option 48 on:

1. Press Add from the control panel’s Start Menu.

2. Press Option #, 48.

3. Press DONE.

Testing

The panel must be programmed before testing.

When installation and programming are complete, test

the AVM as follows.

Audio Verification Module

Page 4

Off-Site Testing

You will need a helper and touch-tone phone at an off-

site location to perform this test.

Note: Option 27 (Ring, Hang, Ring) must be on to

perform the test.

To test the module from off-site:

1. The off-site helper calls the panel, lets the phone

ring once or twice, and hangs up.

2. The helper must call the panel again in 10 to 40

seconds. The panel answers.

3. The helper dials the following on the phone:

* CODE 5.

4. The helper should dial 1 and be able to speak to

you through the AVM.

5. The helper should dial 3 and listen to you.

6. Walk through the vicinity of the AVM while

speaking at a normal conversation level.

7. To return to speaking mode, the helper dials 1.

8. When testing is complete, have the helper dial 99

to hang up.

Central Station Testing

You can also use the central station to test the module.

To test the module from the central station:

1. Inform the central station that you will be sending

an alarm and testing an AVM.

2. Give them the programming selections you made

for the panel.

3. Use a touchpad panic button to initiate an auxil-

iary alarm.

4. The central station operator waits for the alarm to

be reported and initiates an audio session.

5. Have the operator speak to you.

6. Tell the operator to press 3 and walk through the

vicinity of the AVM while speaking at a normal

conversation level.

7. When testing is complete, the operator will end

the session by pressing 99.

Sound Volume

The AVM microphone volume is automatically

controlled and is not adjustable. The speaker volume is

preset to full volume.

If It Doesn’t Work

AVM communication failure usually occurs because of

panel programming errors. Check the programming

selections you made at the panel.

Specifications

Power Requirements: 12 VDC, 10 mA (maximum)

Dimensions: 6.9" L x 4.9" H x 2.5" D

Color: Belgian Grey

Notices

This device complies with part 15 of the FCC rules. Operation is subject to the following

two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may

cause undesired operation.

Changes or modifications not expressly approved by Interactive Technologies, Inc. can

void the users’ authority to operate the equipment

ITI, Simon, and Interrogatorare registered trademarksof Interactive Technologies, Inc..

651-777-2690

651-779-4890

Andere ITI Steuereinheit Handbücher

ITI

ITI 60-620 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung