Jablotron TM-201A Bedienungsanleitung

JABLOTRON ALARMS a.s.

Pod Skalkou 4567/33 46601 Jablonec n. Nisou

Czech Republic www.jablotron.com

TM-201A multi-functional electronic thermometer, - 1 - MNU51203

TM-201A multi-functional electronic thermometer

The TM-201A multi-functional electronic thermometer can be used in all

installations where one or two temperature values need to be measured with

a subsequent relay closing or opening action. The thermometer is equipped

with warning (optical and acoustic) indication. It can be typically used

as a protective thermometer, bistable thermostat or difference thermostat.

Figure 1: Front view

1. Thermometer installation

Install the thermometer in such a way as to make it well visible to the user. Do not install it in places where it may

be exposed to intensive radiant heat. The thermometer is designed for wall-mounted indoor installation. It can be mounted

directly into a common device installation box or on plaster. The bottom part of the housing is always used for this purpose.

1. Remove the top part of the thermometer from the frame (by pushing a screwdriver into the gap between

the display and frame at the T2 indicator).

2. Release the bottom housing by pressing the four latches in the corners (figure 2).

3. First, mount the bottom housing and then snap the display frame into it.

4. Connect the supply cables of the sensors to the T1 and T2 terminals. Always tighten the terminals with

the terminal boards removed. Remove the terminal boards by pulling them towards yourself.

Both the temperature sensors are the same and they can be connected with either polarity. If just one sensor

is sufficient for the selected function of the thermometer, it should always be connected to the T1 terminals.

5. The contacts of the controlled device should be connected to the OUT terminals. The load capacity of the output

is 1 A/250 V and it has safety isolation characteristics. For higher loads use an auxiliary relay or contactor.

6. Connect the 12 V / 50 mA power supply to the + - terminals (observe the correct polarity). As the power supply

unit you can use:

a) LT-089.06 Jablotron.

b) DE06-12 Jablotron.

7. Switch on the power supply.

8. Use the UPŸand DOWNźcontrol keys to set the operational mode of the thermostat and the required

parameters

(see par. 4, Mode selection, Parameter setting).

9. You can reduce the illumination intensity of the display by connecting the LOW INTENSITY jumper

on the thermometer board.

10. Reinsert the top part of the thermometer into the frame.

Figure 2: Bottom housing Figure 3: Description of the terminals and boards

2. Installation of the sensors

Install the CP-201T temperature sensors (not included in the delivery) in the place to be measured (e.g. accumulation tank,

hot water reservoir etc.). Always ensure sufficient thermal contact (we recommend you to use a commonly available heat-

conductive paste). If no pockets are available, attach the sensors to the pipeline using tying tapes with sufficient strength

and insulate the sensors to prevent the ambient temperature from biasing the measurement (you are not recommended

TM-201A multi-functional electronic thermometer, - 2 - MNU51203

to use thin cable ties – they get loose with increasing temperatures and the sensor loses contact with the pipe; using metallic

tapes or collars is preferred).

Caution - the insulation of the supply cables of the sensors is resistant to a max. of 105 °C. The supply cables of the

sensors can be extended with the use of a common cable with copper conductors with a cross-section of at least 0.35 mm2

(the total length of the supply cable of a sensor should not exceed 30m).

3. Front panel indicators

Figure 4: display description: 1 - LED 1 (indicates status of the T1 sensor); 2 - LED 2 (indicates status of the T2 sensor);

3 - LED 3 (warning / closing / opening in the negative logic setting / relay); 4 – Display

4. Mode selection, Parameter setting

The TM-201A thermometer can be used in one of the preset modes (F1 – F5). The selected mode appears on the display

for 3 seconds after connection of the power supply. The F1 operation mode and the values highlighted with bold type

are set as default (in the mode tables see the Default columns).

In the standby condition the TM-201A thermometer shows the temperature measured by the connected sensors

(or “--.-“ if no sensors are connected). If not, briefly disconnect and reconnect the power supply.

At the terminal-board side the thermometer is equipped with two keys that are used to set the operational modes

and parameters. The keys are identified with the Ÿ(UP)and ź(DOWN) symbols. By pressing a key you make a selection

and browse the settings; simultaneous pressing of both the keys is used to enter the setting mode and to confirm

a selection. There is a functional delay during the parameter setting mode; if no key is pressed for a minute, the setting

mode will be terminated, incl. saving all the parameters.

Selecting and setting an operational mode (F1 – F5)

To set an operation mode, follow the points below:

1) Press and hold both the keys ŸDQGź for 6 seconds.

2) A short beep will sound and the current operational mode will start flashing on the display (F1 in the default

setting).

3) Press the

Ÿor źkeys briefly to select the required operational mode (F1 – F5).

4) Confirm the mode by simultaneously pressing the ŸDQGź keys for a short time (for less than 2 seconds).

5) Saving the selected operational mode is indicated by its flashing (for approx. 3 seconds) and a continuous

acoustic signal (for approx. 2 seconds).

6) Now, the first parameter of the selected operational mode is displayed (the P2.1 parameter in the F2 mode,

the P3.1 parameter in the F3 mode etc.) To set the parameters, follow the procedure below.

Figure 5. Example of setting the F3 mode after activation of the thermometer

F1 F2 F3 F4 F5 rES End

Thermometer

with warning

indication

(1 or 2

sensors)

Heating

thermostat

(1 sensor)

Cooling

thermostat

(1 sensor)

Bistable

thermostat

(2 sensors)

Differential

thermostat

(2 sensors)

Restoration

of the

default

settings

End

without

changing the

mode

JABLOTRON ALARMS a.s.

Pod Skalkou 4567/33 46601 Jablonec n. Nisou

Czech Republic www.jablotron.com

TM-201A multi-functional electronic thermometer, - 3 - MNU51203

Restoring the default settings and exiting without saving the changes

1) If you want to restore the default settings of the thermometer, browse to the rES item and simultaneously press

the ŸDQGź keys to confirm it.

2) You can exit the setting mode without changing the mode any time by selecting and confirming the End item,

or by pressing the ŸDQGź keys simultaneously for a long time (6 seconds).

Selecting and setting individual parameters.

To set the parameters of an operational mode, follow the points below:

1) Briefly press the Ÿor źkey.

2) A short beep will sound and the first parameter of the operational mode will appear on the display

(the P2.1 parameter in the F2 mode etc.).

3) Use the Ÿor źkeys to select the parameter you want to set.

4) Press the Ÿand źkeys simultaneously to enter the parameter setting mode. A short beep will sound

and the currently set value will start flashing. Briefly press (or hold) the Ÿor źkey to set the required

parameter value.

5) Briefly press the Ÿand źkeys simultaneously to confirm the parameter setting. Saving is confirmed

by a short beep and displaying the number of the set parameter.

6) Repeat points 3 - 5 to set the other parameters of the particular mode.

7) Exit the setting mode by selecting and confirming the End item. You can also exit the setting mode any time

by allowing a time-out or by simultaneously pressing the Ÿand źkeys for a long time. After the termination

of the setting mode the TM-201A thermometer will return to the standby condition.

Figure 6. Example of setting the P2.3 parameter after activation of the thermometer and with the F2 operation mode selected

4.1. F1 mode – Thermometer with warning indication

A protective thermometer with a warning indication and relay switching, and protection from overheating or freezing.

Parameter Description Range Default

P1.1 Lower limit - a temperature drop below this limit switches the relay and

warning indication. The hysteresis for relay opening is 3 °C.

-20 °C to +105 °C 5 °C

P1.2 Upper limit - a temperature increase above this limit switches the relay

and warning indication. The hysteresis for relay opening is 3 °C.

-20 °C to +105 °C 90 °C

P1.3 Siren - activation/deactivation of acoustic indication. ON / OFF ON

P1.4 T2 sensor - temperature sensor connected to the T2 terminals. ON / OFF ON

P1.5 LED 3 indication – indicates closing (opening in the negative logic) of

the relay.

ON / OFF ON

P1.6 Negative relay logic - reversed logic of the relay function (permanently

closed in the standby condition).

ON / OFF OFF

P1.7 Minimum relay closing time - used to limit too frequent switching on

and off of the connected device. If this parameter is active, the relay will

be closed for at least this time period, regardless of the measured

temperature.

OFF, 1 to 15 min OFF

P1.8 Minimum pause time - used to limit too frequent switching on and off of

the connected device. If this parameter is active, the relay will only be

closed after expiration of this minimum pause period. It is considered

from the last closing of the relay, it is not applied at the first activation of

the thermometer.

OFF, 1 to 15 min OFF

End Exiting the setting mode

TM-201A multi-functional electronic thermometer, - 4 - MNU51203

Example of using the F1 mode

The thermometer only contains one relay; therefore,

only use the relay switching in the F1 mode for monitoring

of the minimum (P1.1) or maximum temperature (P1.2).

The relay will be closed if the temperature drops below

the minimum value or if it exceeds the maximum value.

The closing of the relay can activate remote notification

of the user via an external device. It may also

be accompanied by an acoustic indication (P1.3).

Only one T1 sensor or both the T1 and T2 sensors

can be used (P1.4). If both the sensors are used, the set limit

is monitored by both the sensors (T1 and T2).

4.2. F2 mode – Thermostat (heating)

Parameter Description Range Default

P2.1 Heating temperature - the required temperature of the heating (T1 sensor) -20 °C to +105 °C 25 °C

P2.2 Hysteresis – the temperature drop for heating reactivation. 0.1 °C to 10 °C 1 °C

P2.3 LED 3 indication – indicates closing (opening in the negative logic) of the

relay.

ON / OFF ON

P2.4 Negative relay logic - reversed logic of the relay function (permanently

closed in the standby condition).

ON / OFF OFF

P2.5 Minimum relay closing time - used to limit too frequent switching on and off

of the connected device. Parameter description, see P1.7.

OFF, 1 to 15 min OFF

P2.6 Minimum pause time - used to limit too frequent switching on and off of the

connected device. Parameter description, see P1.8.

OFF, 1 to 15 min OFF

End Exiting the setting mode

4.3. F3 mode – Thermostat (cooling)

Parameter Description Range Default

P3.1 Cooling temperature - the required temperature of the cooling (T1 sensor) -20 °C to +105 °C 20 °C

P3.2 Hysteresis – the temperature increase for cooling reactivation. 0.1 °C to 10 °C 1 °C

P3.3 LED 3 indication – indicates closing (opening in the negative logic) of the

relay.

ON / OFF ON

P3.4 Negative relay logic - reversed logic of the relay function (permanently

closed in the standby condition).

ON / OFF OFF

P3.5 Minimum relay closing time - used to limit too frequent switching on and off

of the connected device. Parameter description, see P1.7.

OFF, 1 to 15 min OFF

P3.6 Minimum pause time - used to limit too frequent switching on and off of the

connected device. Parameter description, see P1.8.

OFF, 1 to 15 min OFF

End Exiting the setting mode

4.4. F4 mode – Bistable thermostat

In this mode the thermostat can be typically used to control preferential heating from an accumulation tank.

Parameter Description Range Default

P4.1 Relay closing temperature by T1 - The T1 sensor is always used to close

the relay that is closed when the set temperature is exceeded.

-20 °C to +105 °C 65 °C

P4.2 Relay opening temperature by T2 - The T2 sensor is always used to open

the relay that is opened when the temperature drops below the set value.

-20 °C to +105 °C 35 °C

JABLOTRON ALARMS a.s.

Pod Skalkou 4567/33 46601 Jablonec n. Nisou

Czech Republic www.jablotron.com

TM-201A multi-functional electronic thermometer, - 5 - MNU51203

P4.3 LED 3 indication – indicates closing (opening in the negative logic) of the

relay.

ON / OFF ON

P4.4 Negative relay logic - reversed logic of the relay function (permanently

closed in the standby condition).

ON / OFF OFF

P4.5 Minimum relay closing time - used to limit too frequent switching on and off

of the connected device. Parameter description, see P1.7.

OFF, 1 to 15 min OFF

P4.6 Minimum pause time - used to limit too frequent switching on and off of the

connected device. Parameter description, see P1.8.

OFF, 1 to 15 min OFF

End Exiting the setting mode

If an installation requires it, the value of the P4.2 parameter can be higher than that of P4.1.

If both the values (T1 and T2) are achieved, the relay will remain closed (T1 takes priority).

Example of using the F4 mode

The thermometer monitors the priority of the accumulation

tank

- T1 for closing (P4.1) – the tank takes priority

- T2 for opening (P4.2) – the boiler takes priority

The relay is closed when the set temperature is achieved

at the T1 sensor and it is opened on cooling at the T2

sensor.

Auxiliary relay(s) can be used not only to switch a valve

(hydraulic switch), but also to block or switch a gas (electric)

boiler.

The relay logic can be reversed (P4.4) depending of the

type of the valve used (normally closed/open).

4.5. Mode F5 – Differential thermostat

Parameter Description Range Default

P5.1 Closing difference - determines the temperature difference of the T1 –

T2 sensors to close the relay.

1 °C to 30 °C 10 °C

P5.2 Opening difference - determines the temperature difference of the T1 –

T2 sensors to open the relay.

1 °C to 30 °C 3 °C

P5.3 Minimum T1 sensor temperature – determines the temperature at the

T1 sensor at which the relay will be closed if the switching difference

condition of P5.1 is met at the same time.

-20 °C to +105 °C 30 °C

P5.4 Maximum T1 sensor operation temperature – if this temperature is

exceeded, the relay will be opened (protective function).

OFF/

-20 °C to +105 °C

OFF

P5.5 Maximum T2 sensor operation temperature – if this temperature is

exceeded, the relay will be opened (protective function).

OFF/

-20 °C to +105 °C

OFF

P5.6 LED 3 indication – indicates closing (opening in the negative logic) of

the relay.

ON / OFF ON

P5.7 Negative relay logic - reversed logic of the relay function (permanently

closed in the standby condition).

ON / OFF OFF

P5.8 Minimum relay closing time - used to limit too frequent switching on

and off of the connected device. Parameter description, see P1.7.

OFF, 1 to 15 min OFF

P5.9 Minimum pause time - used to limit too frequent switching on and off of

the connected device. Parameter description, see P1.8.

OFF, 1 to 15 min OFF

End Exiting the setting mode

The actual possible range of the differences depends on the settings of the limits. Example: If the closing difference is set

to 15°C, the setting range of the opening difference will be 1 °C – 14 °C.

TM-201A multi-functional electronic thermometer, - 6 - MNU51203

Example of using the F5 mode

The thermometer monitors charging of the hot water

reservoir (e.g. in a circuit with a solid fuel boiler)

The relay will be closed if the T1 temperature

of the heating water is higher than the T2 temperature

in the reservoir by the required number of degrees

(P5.1, switching difference).

The relay will be opened if the difference of the T1 – T2

temperatures decreases to the set value (P5.2, opening

difference), or if the maximum set hot water temperature

in the reservoir (P5.5) is achieved.

Thus, the settings of the closing and opening difference

can be used to control exceeding the heating water

temperature. You can also set the minimum T1 operation

temperature to avoid cooling the boiler during the power

increase stage (P5.3).

5. Warning indication

A missing temperature sensor that is required by the selected function is indicated by flashing of LED 3 and the respective

LED 1 or LED 2. If only one sensor can be connected in a particular mode, it must always be connected to the T1 terminal.

In the F1 mode the warning indication is active on exceeding the limit values. The acoustic indication can be deactivated

with the P1.3 parameter. If in the F1 mode no sensor is connected to the T2 terminals, the P1.4 parameter must be

set to OFF. In the F2 – F5 modes lighting of LED 3 may indicate closing/opening of the relay (if indication of the relay status

is activated by the respective parameter).

6. Technical parameters

TM-201A thermometer

Supply voltage 11 V to 17 V DC

Standby consumption/maximum consumption 20 mA/50 mA

Measuring range -40 °C to 125 °C

Temperature sensor type NTC 10 k:, B25/100 = 3455 K

Operating temperature range -10 °C to +40 °C

Seasonal space heating energy efficiency ڦS= 1 % (acc. Regulation (EU) No. 813/2013)

Temperature control class I. (acc. Regulation (EU) No. 813/2013)

OUT output switching contact, max. 1 A/250 V, resistance load 6 A, protection class II

Acoustic/optical indication Siren/LED

Ingress protection class IP 41 (in accordance with EN 60529)

In conformity with EN 60730-1, EN 61000-6-1, EN 61000-6-3, EN 50581

Recommended temperature sensor

Type CP-201T Jablotron (NTC 10 k:, B25/100 = 3455 K)

Measuring range -25 °C to 105 °C

Sensor accuracy ± 1% at 25 °C, ± 2 °C in the range of -25 °C to 105 °C

Specifications CP-201T Manual (NW) MNC52900

JABLOTRON ALARMS a.s. hereby declares that the TM-201A is in a compliance with the relevant Union

harmonisation legislation: Directives No: 2014/35/EU, 2014/30/EU, 2009/125/ES, 2011/65/EU. The original of the

conformity assessment can be found at www.jablotron.com - Section Downloads.

Note: Although this product does not contain any harmful materials we suggest you return the product

to the dealer or directly to the producer after use.

Inhaltsverzeichnis

Andere jablotron Thermometer Handbücher

jablotron

jablotron JB-EXT-TH-B BUS Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung

Veridian Healthcare

Veridian Healthcare 09-349 Bedienungsanleitung

jablotron TM-201A Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken